Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt

Merge "First batch of AT91 DT material for 3.15" from Nicolas Ferre:

- activate DMA for NAND flash controller
- some binding documentation update for usba and ADC (iio) drivers
- removal of some deprecated ADC (iio) properties

* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: at91-cosino: remove useless adc properties
  ARM: at91/dt: sama5d3: remove useless adc properties
  ARM: at91/dt: at91sam9x5: remove useless adc properties
  ARM: at91/dt: at91sam9g45: remove useless adc properties
  ARM: at91/dt: at91sam9260: remove useless adc properties
  ARM: at91/dt: at91-ariag25: remove useless adc properties
  Documentation: dt: iio: move arm/atmel-adc.txt to iio/adc/at91_adc.txt
  Documentation: dt: iio: improve atmel-adc documentation
  ARM: at91: sama5d3: get rid of atmel_tsadcc driver
  ARM: at91/DT: atmel_usba correct atmel,vbus-gpio meaning
  ARM: at91/DT: add NAND + DMA property

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

2 files changed, 19 insertions, 18 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt
index d1061469f63d..82061c7e4fea 100644
--- a/Documentation/devicetree/bindings/arm/atmel-adc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt
@@ -5,32 +5,32 @@ Required properties:
     <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
   - reg: Should contain ADC registers location and length
   - interrupts: Should contain the IRQ line for the ADC
-  - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
-  - atmel,adc-res: List of resolution in bits supported by the ADC. List size
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
 		   must be two at least.
   - atmel,adc-res-names: Contains one identifier string for each resolution
 			 in atmel,adc-res property. "lowres" and "highres"
 			 identifiers are required.
 
 Optional properties:
-  - atmel,adc-use-external: Boolean to enable of external triggers
+  - atmel,adc-use-external-triggers: Boolean to enable the external triggers
   - atmel,adc-use-res: String corresponding to an identifier from
 		       atmel,adc-res-names property. If not specified, the highest
 		       resolution will be used.
   - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
   - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
-  - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
-                        value is set, then adc driver will enable touch screen
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
                         support.
-    NOTE: when adc touch screen enabled, the adc hardware trigger will be
-          disabled. Since touch screen will occupied the trigger register.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
   - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
-                                     make touch detect more precision.
- 
+                                     makes touch detection more precise.
+
 Optional trigger Nodes:
   - Required properties:
     * trigger-name: Name of the trigger exposed to the user
@@ -41,40 +41,41 @@ Optional trigger Nodes:
 
 Examples:
 adc0: adc@fffb0000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
-	interrupts = <20 4>;
-	atmel,adc-channel-base = <0x30>;
+	interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 	atmel,adc-channels-used = <0xff>;
-	atmel,adc-drdy-mask = <0x10000>;
-	atmel,adc-num-channels = <8>;
 	atmel,adc-startup-time = <40>;
-	atmel,adc-status-register = <0x1c>;
-	atmel,adc-trigger-register = <0x08>;
-	atmel,adc-use-external;
+	atmel,adc-use-external-triggers;
 	atmel,adc-vref = <3300>;
 	atmel,adc-res = <8 10>;
 	atmel,adc-res-names = "lowres", "highres";
 	atmel,adc-use-res = "lowres";
 
 	trigger@0 {
+		reg = <0>;
 		trigger-name = "external-rising";
 		trigger-value = <0x1>;
 		trigger-external;
 	};
 	trigger@1 {
+		reg = <1>;
 		trigger-name = "external-falling";
 		trigger-value = <0x2>;
 		trigger-external;
 	};
 
 	trigger@2 {
+		reg = <2>;
 		trigger-name = "external-any";
 		trigger-value = <0x3>;
 		trigger-external;
 	};
 
 	trigger@3 {
+		reg = <3>;
 		trigger-name = "continuous";
 		trigger-value = <0x6>;
 	};
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index 55f51af08bc7..bc2222ca3f2a 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -57,8 +57,8 @@ Required properties:
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
- - atmel,vbus-gpio: If present, specifies a gpio that needs to be
-   activated for the bus to be powered.
+ - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether
+   vbus is present (USB is connected).
 
 Required child node properties:
  - name: Name of the endpoint.