Merge 5.16-rc8 into usb-next

We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8 files changed, 53 insertions, 14 deletions

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 9725c546a0d4..2fba82431efb 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -1689,6 +1689,8 @@
 			architectures force reset to be always executed
 	i8042.unlock	[HW] Unlock (ignore) the keylock
 	i8042.kbdreset	[HW] Reset device connected to KBD port
+	i8042.probe_defer
+			[HW] Allow deferred probing upon i8042 probe errors
 
 	i810=		[HW,DRM]
 
@@ -2413,8 +2415,12 @@
 			Default is 1 (enabled)
 
 	kvm-intel.emulate_invalid_guest_state=
-			[KVM,Intel] Enable emulation of invalid guest states
-			Default is 0 (disabled)
+			[KVM,Intel] Disable emulation of invalid guest state.
+			Ignored if kvm-intel.enable_unrestricted_guest=1, as
+			guest state is never invalid for unrestricted guests.
+			This param doesn't apply to nested guests (L2), as KVM
+			never emulates invalid L2 guest state.
+			Default is 1 (enabled)
 
 	kvm-intel.flexpriority=
 			[KVM,Intel] Disable FlexPriority feature (TPR shadow).
diff --git a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.yaml b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.yaml
index 80a63d47790a..c98929a213e9 100644
--- a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.yaml
+++ b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.yaml
@@ -51,6 +51,19 @@ patternProperties:
     description:
       Properties for single BUCK regulator.
 
+    properties:
+      op_mode:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 1
+        description: |
+          Describes the different operating modes of the regulator with power
+          mode change in SOC. The different possible values are:
+            0 - always off mode
+            1 - on in normal mode
+            2 - low power mode
+            3 - suspend mode
+
     required:
       - regulator-name
 
@@ -63,6 +76,18 @@ patternProperties:
       Properties for single BUCK regulator.
 
     properties:
+      op_mode:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [0, 1, 2, 3]
+        default: 1
+        description: |
+          Describes the different operating modes of the regulator with power
+          mode change in SOC. The different possible values are:
+            0 - always off mode
+            1 - on in normal mode
+            2 - low power mode
+            3 - suspend mode
+
       s5m8767,pmic-ext-control-gpios:
         maxItems: 1
         description: |
diff --git a/Documentation/i2c/summary.rst b/Documentation/i2c/summary.rst
index 136c4e333be7..786c618ba3be 100644
--- a/Documentation/i2c/summary.rst
+++ b/Documentation/i2c/summary.rst
@@ -11,9 +11,11 @@ systems.  Some systems use variants that don't meet branding requirements,
 and so are not advertised as being I2C but come under different names,
 e.g. TWI (Two Wire Interface), IIC.
 
-The official I2C specification is the `"I2C-bus specification and user
-manual" (UM10204) <https://www.nxp.com/docs/en/user-guide/UM10204.pdf>`_
-published by NXP Semiconductors.
+The latest official I2C specification is the `"I2C-bus specification and user
+manual" (UM10204) <https://www.nxp.com/webapp/Download?colCode=UM10204>`_
+published by NXP Semiconductors. However, you need to log-in to the site to
+access the PDF. An older version of the specification (revision 6) is archived
+`here <https://web.archive.org/web/20210813122132/https://www.nxp.com/docs/en/user-guide/UM10204.pdf>`_.
 
 SMBus (System Management Bus) is based on the I2C protocol, and is mostly
 a subset of I2C protocols and signaling.  Many I2C devices will work on an
diff --git a/Documentation/networking/bonding.rst b/Documentation/networking/bonding.rst
index 31cfd7d674a6..c0a789b00806 100644
--- a/Documentation/networking/bonding.rst
+++ b/Documentation/networking/bonding.rst
@@ -196,11 +196,12 @@ ad_actor_sys_prio
 ad_actor_system
 
 	In an AD system, this specifies the mac-address for the actor in
-	protocol packet exchanges (LACPDUs). The value cannot be NULL or
-	multicast. It is preferred to have the local-admin bit set for this
-	mac but driver does not enforce it. If the value is not given then
-	system defaults to using the masters' mac address as actors' system
-	address.
+	protocol packet exchanges (LACPDUs). The value cannot be a multicast
+	address. If the all-zeroes MAC is specified, bonding will internally
+	use the MAC of the bond itself. It is preferred to have the
+	local-admin bit set for this mac but driver does not enforce it. If
+	the value is not given then system defaults to using the masters'
+	mac address as actors' system address.
 
 	This parameter has effect only in 802.3ad mode and is available through
 	SysFs interface.
diff --git a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst
index d638b5a8aadd..199647729251 100644
--- a/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst
+++ b/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/overview.rst
@@ -183,6 +183,7 @@ PHY and allows physical transmission and reception of Ethernet frames.
   IRQ config, enable, reset
 
 DPNI (Datapath Network Interface)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 Contains TX/RX queues, network interface configuration, and RX buffer pool
 configuration mechanisms.  The TX/RX queues are in memory and are identified
 by queue number.
diff --git a/Documentation/networking/ip-sysctl.rst b/Documentation/networking/ip-sysctl.rst
index c04431144f7a..2572eecc3e86 100644
--- a/Documentation/networking/ip-sysctl.rst
+++ b/Documentation/networking/ip-sysctl.rst
@@ -25,7 +25,8 @@ ip_default_ttl - INTEGER
 ip_no_pmtu_disc - INTEGER
 	Disable Path MTU Discovery. If enabled in mode 1 and a
 	fragmentation-required ICMP is received, the PMTU to this
-	destination will be set to min_pmtu (see below). You will need
+	destination will be set to the smallest of the old MTU to
+	this destination and min_pmtu (see below). You will need
 	to raise min_pmtu to the smallest interface MTU on your system
 	manually if you want to avoid locally generated fragments.
 
@@ -49,7 +50,8 @@ ip_no_pmtu_disc - INTEGER
 	Default: FALSE
 
 min_pmtu - INTEGER
-	default 552 - minimum discovered Path MTU
+	default 552 - minimum Path MTU. Unless this is changed mannually,
+	each cached pmtu will never be lower than this setting.
 
 ip_forward_use_pmtu - BOOLEAN
 	By default we don't trust protocol path MTUs while forwarding
diff --git a/Documentation/networking/timestamping.rst b/Documentation/networking/timestamping.rst
index 80b13353254a..f5809206eb93 100644
--- a/Documentation/networking/timestamping.rst
+++ b/Documentation/networking/timestamping.rst
@@ -582,8 +582,8 @@ Time stamps for outgoing packets are to be generated as follows:
   and hardware timestamping is not possible (SKBTX_IN_PROGRESS not set).
 - As soon as the driver has sent the packet and/or obtained a
   hardware time stamp for it, it passes the time stamp back by
-  calling skb_hwtstamp_tx() with the original skb, the raw
-  hardware time stamp. skb_hwtstamp_tx() clones the original skb and
+  calling skb_tstamp_tx() with the original skb, the raw
+  hardware time stamp. skb_tstamp_tx() clones the original skb and
   adds the timestamps, therefore the original skb has to be freed now.
   If obtaining the hardware time stamp somehow fails, then the driver
   should not fall back to software time stamping. The rationale is that
diff --git a/Documentation/sound/hd-audio/models.rst b/Documentation/sound/hd-audio/models.rst
index 0ea967d34583..d25335993e55 100644
--- a/Documentation/sound/hd-audio/models.rst
+++ b/Documentation/sound/hd-audio/models.rst
@@ -326,6 +326,8 @@ usi-headset
     Headset support on USI machines
 dual-codecs
     Lenovo laptops with dual codecs
+alc285-hp-amp-init
+    HP laptops which require speaker amplifier initialization (ALC285)
 
 ALC680
 ======