Merge tag 'qcom-arm64-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm ARM64 Updates for v4.18

* Add support for SDM845 and associated peripherals
* Fix gic_irq_domain_translation warnings on Qualcomm platforms
* Add binding for GENI SE, Qualcomm bluetooth, and Command DB
* Add support for SDHCI and ramoops on MSM8992
* Fixup qcom,pcie devices to pcie
* Add wlan, bluetooth, and micro SD supplies on db820c
* Add UFS related nodes on MSM8996

* tag 'qcom-arm64-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: qcom: msm8996: Add ufs related nodes
  arm64: dts: msm8996: fix gic_irq_domain_translate warnings
  arm64: dts: qcom: sdm845: Sort nodes in the soc by address
  arm64: dts: qcom: sdm845: Sort nodes in the reserved mem by address
  arm64: dts: sdm845: Add command DB node
  arm64: dts: sdm845: Fix xo_board clock name and speed
  arm64: dts: qcom: Add SDM845 SMEM nodes
  arm64: dts: qcom: Add APSS shared mailbox node to SDM845
  arm64: dts: msm8916: fix gic_irq_domain_translate warnings
  dt-bindings: introduce Command DB for QCOM SoCs
  arm64: dts: apq8096-db820c: Add micro sd card supplies
  dt-bindings: soc: qcom: Add device tree binding for GENI SE
  dt-bindings: net: bluetooth: Add qualcomm-bluetooth
  arm64: dts: apq8096-db820c: enable bluetooth node
  arm64: dts: apq8096-db820c: Enable wlan and bt en pins
  arm64: dts: qcom: rename qcom,pcie devices to pcie
  arm64: dts: msm8992: add pstore-ramoops support
  arm64: dts: sdm845: Add minimal dts/dtsi files for sdm845 SoC and MTP
  arm64: dts: Enable onboard SDHCI on msm8992

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 186 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
new file mode 100644
index 000000000000..0ea18a53cc29
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
@@ -0,0 +1,30 @@
+Qualcomm Bluetooth Chips
+---------------------
+
+This documents the binding structure and common properties for serial
+attached Qualcomm devices.
+
+Serial attached Qualcomm devices shall be a child node of the host UART
+device the slave device is attached to.
+
+Required properties:
+ - compatible: should contain one of the following:
+   * "qcom,qca6174-bt"
+
+Optional properties:
+ - enable-gpios: gpio specifier used to enable chip
+ - clocks: clock provided to the controller (SUSCLK_32KHZ)
+
+Example:
+
+serial@7570000 {
+	label = "BT-UART";
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,qca6174-bt";
+
+		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+		clocks = <&divclk4>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt b/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt
new file mode 100644
index 000000000000..68395530c0a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/reserved-memory/qcom,cmd-db.txt
@@ -0,0 +1,37 @@
+Command DB
+---------
+
+Command DB is a database that provides a mapping between resource key and the
+resource address for a system resource managed by a remote processor. The data
+is stored in a shared memory region and is loaded by the remote processor.
+
+Some of the Qualcomm Technologies Inc SoC's have hardware accelerators for
+controlling shared resources. Depending on the board configuration the shared
+resource properties may change. These properties are dynamically probed by the
+remote processor and made available in the shared memory.
+
+The bindings for Command DB is specified in the reserved-memory section in
+devicetree. The devicetree representation of the command DB driver should be:
+
+Properties:
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: Should be "qcom,cmd-db"
+
+- reg:
+	Usage: required
+	Value type: <prop encoded array>
+	Definition: The register address that points to the actual location of
+		    the Command DB in memory.
+
+Example:
+
+	reserved-memory {
+		[...]
+		reserved-memory@85fe0000 {
+			reg = <0x0 0x85fe0000 0x0 0x20000>;
+			compatible = "qcom,cmd-db";
+			no-map;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
new file mode 100644
index 000000000000..d330c73de9a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -0,0 +1,119 @@
+Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
+
+Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
+is a programmable module for supporting a wide range of serial interfaces
+like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
+Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
+Wrapper controller is modeled as a node with zero or more child nodes each
+representing a serial engine.
+
+Required properties:
+- compatible:		Must be "qcom,geni-se-qup".
+- reg:			Must contain QUP register address and length.
+- clock-names:		Must contain "m-ahb" and "s-ahb".
+- clocks:		AHB clocks needed by the device.
+
+Required properties if child node exists:
+- #address-cells: 	Must be <1> for Serial Engine Address
+- #size-cells: 		Must be <1> for Serial Engine Address Size
+- ranges: 		Must be present
+
+Properties for children:
+
+A GENI based QUP wrapper controller node can contain 0 or more child nodes
+representing serial devices.  These serial devices can be a QCOM UART, I2C
+controller, SPI controller, or some combination of aforementioned devices.
+Please refer below the child node definitions for the supported serial
+interface protocols.
+
+Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller
+
+Required properties:
+- compatible:		Must be "qcom,geni-i2c".
+- reg: 			Must contain QUP register address and length.
+- interrupts: 		Must contain I2C interrupt.
+- clock-names: 		Must contain "se".
+- clocks: 		Serial engine core clock needed by the device.
+- #address-cells:	Must be <1> for I2C device address.
+- #size-cells:		Must be <0> as I2C addresses have no size component.
+
+Optional property:
+- clock-frequency:	Desired I2C bus clock frequency in Hz.
+			When missing default to 400000Hz.
+
+Child nodes should conform to I2C bus binding as described in i2c.txt.
+
+Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
+
+Required properties:
+- compatible:		Must be "qcom,geni-debug-uart".
+- reg: 			Must contain UART register location and length.
+- interrupts: 		Must contain UART core interrupts.
+- clock-names:		Must contain "se".
+- clocks:		Serial engine core clock needed by the device.
+
+Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller
+
+Required properties:
+- compatible:		Must contain "qcom,geni-spi".
+- reg:			Must contain SPI register location and length.
+- interrupts:		Must contain SPI controller interrupts.
+- clock-names:		Must contain "se".
+- clocks:		Serial engine core clock needed by the device.
+- spi-max-frequency:	Specifies maximum SPI clock frequency, units - Hz.
+- #address-cells:	Must be <1> to define a chip select address on
+			the SPI bus.
+- #size-cells:		Must be <0>.
+
+SPI slave nodes must be children of the SPI master node and conform to SPI bus
+binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+	geniqup@8c0000 {
+		compatible = "qcom,geni-se-qup";
+		reg = <0x8c0000 0x6000>;
+		clock-names = "m-ahb", "s-ahb";
+		clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+			<&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		i2c0: i2c@a94000 {
+			compatible = "qcom,geni-i2c";
+			reg = <0xa94000 0x4000>;
+			interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "se";
+			clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&qup_1_i2c_5_active>;
+			pinctrl-1 = <&qup_1_i2c_5_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@a88000 {
+			compatible = "qcom,geni-debug-uart";
+			reg = <0xa88000 0x7000>;
+			interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "se";
+			clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&qup_1_uart_3_active>;
+			pinctrl-1 = <&qup_1_uart_3_sleep>;
+		};
+
+		spi0: spi@a84000 {
+			compatible = "qcom,geni-spi";
+			reg = <0xa84000 0x4000>;
+			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "se";
+			clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&qup_1_spi_2_active>;
+			pinctrl-1 = <&qup_1_spi_2_sleep>;
+			spi-max-frequency = <19200000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	}