Merge branch 'tegra/clk' into next/dt2

This is a dependency for the tegra/dt branch.

Conflicts:
	drivers/clocksource/tegra20_timer.c

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

7 files changed, 495 insertions, 5 deletions

diff --git a/Documentation/arm/sunxi/clocks.txt b/Documentation/arm/sunxi/clocks.txt
new file mode 100644
index 000000000000..e09a88aa3136
--- /dev/null
+++ b/Documentation/arm/sunxi/clocks.txt
@@ -0,0 +1,56 @@
+Frequently asked questions about the sunxi clock system
+=======================================================
+
+This document contains useful bits of information that people tend to ask
+about the sunxi clock system, as well as accompanying ASCII art when adequate.
+
+Q: Why is the main 24MHz oscillator gatable? Wouldn't that break the
+   system?
+
+A: The 24MHz oscillator allows gating to save power. Indeed, if gated
+   carelessly the system would stop functioning, but with the right
+   steps, one can gate it and keep the system running. Consider this
+   simplified suspend example:
+
+   While the system is operational, you would see something like
+
+      24MHz         32kHz
+       |
+      PLL1
+       \
+        \_ CPU Mux
+             |
+           [CPU]
+
+   When you are about to suspend, you switch the CPU Mux to the 32kHz
+   oscillator:
+
+      24Mhz         32kHz
+       |              |
+      PLL1            |
+                     /
+           CPU Mux _/
+             |
+           [CPU]
+
+    Finally you can gate the main oscillator
+
+                    32kHz
+                      |
+                      |
+                     /
+           CPU Mux _/
+             |
+           [CPU]
+
+Q: Were can I learn more about the sunxi clocks?
+
+A: The linux-sunxi wiki contains a page documenting the clock registers,
+   you can find it at
+
+        http://linux-sunxi.org/A10/CCM
+
+   The authoritative source for information at this time is the ccmu driver
+   released by Allwinner, you can find it at
+
+        https://github.com/linux-sunxi/linux-sunxi/tree/sunxi-3.0/arch/arm/mach-sun4i/clock/ccmu
diff --git a/Documentation/clk.txt b/Documentation/clk.txt
index 1943fae014fd..4274a546eb57 100644
--- a/Documentation/clk.txt
+++ b/Documentation/clk.txt
@@ -174,9 +174,9 @@ int clk_foo_enable(struct clk_hw *hw)
 };
 
 Below is a matrix detailing which clk_ops are mandatory based upon the
-hardware capbilities of that clock.  A cell marked as "y" means
+hardware capabilities of that clock.  A cell marked as "y" means
 mandatory, a cell marked as "n" implies that either including that
-callback is invalid or otherwise uneccesary.  Empty cells are either
+callback is invalid or otherwise unnecessary.  Empty cells are either
 optional or must be evaluated on a case-by-case basis.
 
                            clock hardware characteristics
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
index b5846e21cc2e..1608a54e90e1 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -1,19 +1,84 @@
 NVIDIA Tegra Power Management Controller (PMC)
 
-Properties:
+The PMC block interacts with an external Power Management Unit. The PMC
+mostly controls the entry and exit of the system from different sleep
+modes. It provides power-gating controllers for SoC and CPU power-islands.
+
+Required properties:
 - name : Should be pmc
 - compatible : Should contain "nvidia,tegra<chip>-pmc".
 - reg : Offset and length of the register set for the device
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pclk" (The Tegra clock of that name),
+  "clk32k_in" (The 32KHz clock input to Tegra).
+
+Optional properties:
 - nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
   The PMU is an external Power Management Unit, whose interrupt output
   signal is fed into the PMC. This signal is optionally inverted, and then
   fed into the ARM GIC. The PMC is not involved in the detection or
   handling of this interrupt signal, merely its inversion.
+- nvidia,suspend-mode : The suspend mode that the platform should use.
+  Valid values are 0, 1 and 2:
+  0 (LP0): CPU + Core voltage off and DRAM in self-refresh
+  1 (LP1): CPU voltage off and DRAM in self-refresh
+  2 (LP2): CPU voltage off
+- nvidia,core-power-req-active-high : Boolean, core power request active-high
+- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high
+- nvidia,combined-power-req : Boolean, combined power request for CPU & Core
+- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC)
+			   is enabled.
+
+Required properties when nvidia,suspend-mode is specified:
+- nvidia,cpu-pwr-good-time : CPU power good time in uS.
+- nvidia,cpu-pwr-off-time : CPU power off time in uS.
+- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time>
+			      Core power good time in uS.
+- nvidia,core-pwr-off-time : Core power off time in uS.
+
+Required properties when nvidia,suspend-mode=<0>:
+- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector
+  The LP0 vector contains the warm boot code that is executed by AVP when
+  resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7
+  processor and always being the first boot processor when chip is power on
+  or resume from deep sleep mode. When the system is resumed from the deep
+  sleep mode, the warm boot code will restore some PLLs, clocks and then
+  bring up CPU0 for resuming the system.
 
 Example:
 
+/ SoC dts including file
 pmc@7000f400 {
 	compatible = "nvidia,tegra20-pmc";
 	reg = <0x7000e400 0x400>;
+	clocks = <&tegra_car 110>, <&clk32k_in>;
+	clock-names = "pclk", "clk32k_in";
 	nvidia,invert-interrupt;
+	nvidia,suspend-mode = <1>;
+	nvidia,cpu-pwr-good-time = <2000>;
+	nvidia,cpu-pwr-off-time = <100>;
+	nvidia,core-pwr-good-time = <3845 3845>;
+	nvidia,core-pwr-off-time = <458>;
+	nvidia,core-power-req-active-high;
+	nvidia,sys-clock-req-active-high;
+	nvidia,lp0-vec = <0xbdffd000 0x2000>;
+};
+
+/ Tegra board dts file
+{
+	...
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk32k_in: clock {
+			compatible = "fixed-clock";
+			reg=<0>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+	...
 };
diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt
new file mode 100644
index 000000000000..028b493e97ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt
@@ -0,0 +1,22 @@
+Binding for the axi-clkgen clock generator
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "adi,axi-clkgen".
+- #clock-cells : from common clock binding; Should always be set to 0.
+- reg : Address and length of the axi-clkgen register set.
+- clocks : Phandle and clock specifier for the parent clock.
+
+Optional properties:
+- clock-output-names : From common clock binding.
+
+Example:
+	clock@0xff000000 {
+		compatible = "adi,axi-clkgen";
+		#clock-cells = <0>;
+		reg = <0xff000000 0x1000>;
+		clocks = <&osc 1>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt
new file mode 100644
index 000000000000..d6cb083b90a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt
@@ -0,0 +1,303 @@
+NVIDIA Tegra114 Clock And Reset Controller
+
+This binding uses the common clock binding:
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The CAR (Clock And Reset) Controller on Tegra is the HW module responsible
+for muxing and gating Tegra's clocks, and setting their rates.
+
+Required properties :
+- compatible : Should be "nvidia,tegra114-car"
+- reg : Should contain CAR registers location and length
+- clocks : Should contain phandle and clock specifiers for two clocks:
+  the 32 KHz "32k_in", and the board-specific oscillator "osc".
+- #clock-cells : Should be 1.
+  In clock consumers, this cell represents the clock ID exposed by the CAR.
+
+  The first 160 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB
+  registers. These IDs often match those in the CAR's RST_DEVICES registers,
+  but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In
+  this case, those clocks are assigned IDs above 160 in order to highlight
+  this issue. Implementations that interpret these clock IDs as bit values
+  within the CLK_OUT_ENB or RST_DEVICES registers should be careful to
+  explicitly handle these special cases.
+
+  The balance of the clocks controlled by the CAR are assigned IDs of 160 and
+  above.
+
+  0	unassigned
+  1	unassigned
+  2	unassigned
+  3	unassigned
+  4	rtc
+  5	timer
+  6	uarta
+  7	unassigned	(register bit affects uartb and vfir)
+  8	unassigned
+  9	sdmmc2
+  10	unassigned	(register bit affects spdif_in and spdif_out)
+  11	i2s1
+  12	i2c1
+  13	ndflash
+  14	sdmmc1
+  15	sdmmc4
+  16	unassigned
+  17	pwm
+  18	i2s2
+  19	epp
+  20	unassigned	(register bit affects vi and vi_sensor)
+  21	2d
+  22	usbd
+  23	isp
+  24	3d
+  25	unassigned
+  26	disp2
+  27	disp1
+  28	host1x
+  29	vcp
+  30	i2s0
+  31	unassigned
+
+  32	unassigned
+  33	unassigned
+  34	apbdma
+  35	unassigned
+  36	kbc
+  37	unassigned
+  38	unassigned
+  39	unassigned	(register bit affects fuse and fuse_burn)
+  40	kfuse
+  41	sbc1
+  42	nor
+  43	unassigned
+  44	sbc2
+  45	unassigned
+  46	sbc3
+  47	i2c5
+  48	dsia
+  49	unassigned
+  50	mipi
+  51	hdmi
+  52	csi
+  53	unassigned
+  54	i2c2
+  55	uartc
+  56	mipi-cal
+  57	emc
+  58	usb2
+  59	usb3
+  60	msenc
+  61	vde
+  62	bsea
+  63	bsev
+
+  64	unassigned
+  65	uartd
+  66	unassigned
+  67	i2c3
+  68	sbc4
+  69	sdmmc3
+  70	unassigned
+  71	owr
+  72	afi
+  73	csite
+  74	unassigned
+  75	unassigned
+  76	la
+  77	trace
+  78	soc_therm
+  79	dtv
+  80	ndspeed
+  81	i2cslow
+  82	dsib
+  83	tsec
+  84	unassigned
+  85	unassigned
+  86	unassigned
+  87	unassigned
+  88	unassigned
+  89	xusb_host
+  90	unassigned
+  91	msenc
+  92	csus
+  93	unassigned
+  94	unassigned
+  95	unassigned	(bit affects xusb_dev and xusb_dev_src)
+
+  96	unassigned
+  97	unassigned
+  98	unassigned
+  99	mselect
+  100	tsensor
+  101	i2s3
+  102	i2s4
+  103	i2c4
+  104	sbc5
+  105	sbc6
+  106	d_audio
+  107	apbif
+  108	dam0
+  109	dam1
+  110	dam2
+  111	hda2codec_2x
+  112	unassigned
+  113	audio0_2x
+  114	audio1_2x
+  115	audio2_2x
+  116	audio3_2x
+  117	audio4_2x
+  118	spdif_2x
+  119	actmon
+  120	extern1
+  121	extern2
+  122	extern3
+  123	unassigned
+  124	unassigned
+  125	hda
+  126	unassigned
+  127	se
+
+  128	hda2hdmi
+  129	unassigned
+  130	unassigned
+  131	unassigned
+  132	unassigned
+  133	unassigned
+  134	unassigned
+  135	unassigned
+  136	unassigned
+  137	unassigned
+  138	unassigned
+  139	unassigned
+  140	unassigned
+  141	unassigned
+  142	unassigned
+  143	unassigned	(bit affects xusb_falcon_src, xusb_fs_src,
+			 xusb_host_src and xusb_ss_src)
+  144	cilab
+  145	cilcd
+  146	cile
+  147	dsialp
+  148	dsiblp
+  149	unassigned
+  150	dds
+  151	unassigned
+  152	dp2
+  153	amx
+  154	adx
+  155	unassigned	(bit affects dfll_ref and dfll_soc)
+  156	xusb_ss
+
+  192	uartb
+  193	vfir
+  194	spdif_in
+  195	spdif_out
+  196	vi
+  197	vi_sensor
+  198	fuse
+  199	fuse_burn
+  200	clk_32k
+  201	clk_m
+  202	clk_m_div2
+  203	clk_m_div4
+  204	pll_ref
+  205	pll_c
+  206	pll_c_out1
+  207	pll_c2
+  208	pll_c3
+  209	pll_m
+  210	pll_m_out1
+  211	pll_p
+  212	pll_p_out1
+  213	pll_p_out2
+  214	pll_p_out3
+  215	pll_p_out4
+  216	pll_a
+  217	pll_a_out0
+  218	pll_d
+  219	pll_d_out0
+  220	pll_d2
+  221	pll_d2_out0
+  222	pll_u
+  223	pll_u_480M
+  224	pll_u_60M
+  225	pll_u_48M
+  226	pll_u_12M
+  227	pll_x
+  228	pll_x_out0
+  229	pll_re_vco
+  230	pll_re_out
+  231	pll_e_out0
+  232	spdif_in_sync
+  233	i2s0_sync
+  234	i2s1_sync
+  235	i2s2_sync
+  236	i2s3_sync
+  237	i2s4_sync
+  238	vimclk_sync
+  239	audio0
+  240	audio1
+  241	audio2
+  242	audio3
+  243	audio4
+  244	spdif
+  245	clk_out_1
+  246	clk_out_2
+  247	clk_out_3
+  248	blink
+  252	xusb_host_src
+  253	xusb_falcon_src
+  254	xusb_fs_src
+  255	xusb_ss_src
+  256	xusb_dev_src
+  257	xusb_dev
+  258	xusb_hs_src
+  259	sclk
+  260	hclk
+  261	pclk
+  262	cclk_g
+  263	cclk_lp
+  264	dfll_ref
+  265	dfll_soc
+
+Example SoC include file:
+
+/ {
+	tegra_car: clock {
+		compatible = "nvidia,tegra114-car";
+		reg = <0x60006000 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	usb@c5004000 {
+		clocks = <&tegra_car 58>; /* usb2 */
+	};
+};
+
+Example board file:
+
+/ {
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		osc: clock@0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <12000000>;
+		};
+
+		clk_32k: clock@1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	&tegra_car {
+		clocks = <&clk_32k> <&osc>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt
index 0921fac73528..e885680f6b45 100644
--- a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt
@@ -120,8 +120,8 @@ Required properties :
   90	clk_d
   91	unassigned
   92	sus
-  93	cdev1
-  94	cdev2
+  93	cdev2
+  94	cdev1
   95	unassigned
 
   96	uart2
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
new file mode 100644
index 000000000000..20b8479c2760
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -0,0 +1,44 @@
+Device Tree Clock bindings for arch-sunxi
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of the following:
+	"allwinner,sun4i-osc-clk" - for a gatable oscillator
+	"allwinner,sun4i-pll1-clk" - for the main PLL clock
+	"allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock
+	"allwinner,sun4i-axi-clk" - for the AXI clock
+	"allwinner,sun4i-ahb-clk" - for the AHB clock
+	"allwinner,sun4i-apb0-clk" - for the APB0 clock
+	"allwinner,sun4i-apb1-clk" - for the APB1 clock
+	"allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing
+
+Required properties for all clocks:
+- reg : shall be the control register address for the clock.
+- clocks : shall be the input parent clock(s) phandle for the clock
+- #clock-cells : from common clock binding; shall be set to 0.
+
+For example:
+
+osc24M: osc24M@01c20050 {
+	#clock-cells = <0>;
+	compatible = "allwinner,sun4i-osc-clk";
+	reg = <0x01c20050 0x4>;
+	clocks = <&osc24M_fixed>;
+};
+
+pll1: pll1@01c20000 {
+	#clock-cells = <0>;
+	compatible = "allwinner,sun4i-pll1-clk";
+	reg = <0x01c20000 0x4>;
+	clocks = <&osc24M>;
+};
+
+cpu: cpu@01c20054 {
+	#clock-cells = <0>;
+	compatible = "allwinner,sun4i-cpu-clk";
+	reg = <0x01c20054 0x4>;
+	clocks = <&osc32k>, <&osc24M>, <&pll1>;
+};