Merge tag 'qcom-dts-for-6.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt

More Qualcomm DTS updates for 6.2

This introduces support for the OnePlus One, on MSM8974Pro, and properly
marks other Pro devices as compatible thereof. Also on MSM8974, the
description of USB devices and their PHYs are cleaned up.

On the binding side compatibles for recently added ARM and ARM64 boards
are added.

* tag 'qcom-dts-for-6.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (102 commits)
  dt-bindings: arm: qcom: Add zombie
  ARM: dts: qcom: msm8974: Add OnePlus One
  dt-bindings: arm: qcom: Document oneplus,bacon device
  ARM: dts: qcom: msm8974: clean up USB nodes
  arm: dts: qcom: use qcom,msm8974pro for pro devices
  dt-bindings: arm: qcom: split MSM8974 Pro and MSM8974
  ARM: dts: qcom: align LED node names with dtschema
  dt-bindings: arm: qcom: Document additional sa8540p device
  dt-bindings: arm: qcom: Add Xperia 5 IV (PDX224)
  dt-bindings: arm: qcom: Document msm8956 and msm8976 SoC and devices
  dt-bindings: arm: add xiaomi,sagit board based on msm8998 chip
  dt-bindings: arm: qcom: add sdm670 and pixel 3a compatible
  dt-bindings: arm: cpus: add qcom kryo 360 compatible
  ARM: dts: qcom-msm8960-cdp: align TLMM pin configuration with DT schema
  ARM: dts: qcom-msm8960: use define for interrupt constants
  dt-bindings: arm: qcom: Document SM6375 & Xperia 10 IV
  ARM: dts: qcom-apq8060: align TLMM pin configuration with DT schema
  ARM: dts: qcom: msm8226: Add MMCC node
  dt-bindings: arm: qcom: Separate LTE/WIFI SKU for sc7280-evoker
  dt-bindings: arm: qcom: Document QDU1000/QRU1000 SoCs and boards
  ...

Link: https://lore.kernel.org/r/20221207153201.3233015-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

44 files changed, 3856 insertions, 2700 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 621cda54eac1..d08a3c450ce7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1033,7 +1033,9 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
 dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8016-sbc.dtb \
 	qcom-apq8026-asus-sparrow.dtb \
+	qcom-apq8026-huawei-sturgeon.dtb \
 	qcom-apq8026-lg-lenok.dtb \
+	qcom-apq8026-samsung-matisse-wifi.dtb \
 	qcom-apq8060-dragonboard.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
@@ -1063,6 +1065,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-rhine-amami.dtb \
 	qcom-msm8974-sony-xperia-rhine-honami.dtb \
 	qcom-msm8974pro-fairphone-fp2.dtb \
+	qcom-msm8974pro-oneplus-bacon.dtb \
 	qcom-msm8974pro-samsung-klte.dtb \
 	qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
index 215613c65250..7a80e1c9f126 100644
--- a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
@@ -87,7 +87,7 @@
 };
 
 &rpm_requests {
-	pm8226-regulators {
+	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
 
 		pm8226_s3: s3 {
diff --git a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
new file mode 100644
index 000000000000..d64096028ab1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "Huawei Watch";
+	compatible = "huawei,sturgeon", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 4>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c5 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vio-supply = <&pm8226_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_3 {
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-voltage = <4370000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,minimum-input-voltage = <4350000>;
+	qcom,fast-charge-current-limit = <300000>;
+	qcom,fast-charge-safe-current = <600000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio63", "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	touch_default_state: touch-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
index 193569f0ca5f..de2fb1c01b6e 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
@@ -13,6 +13,7 @@
 / {
 	model = "LG G Watch R";
 	compatible = "lg,lenok", "qcom,apq8026";
+	chassis-type = "watch";
 	qcom,board-id = <132 0x0a>;
 	qcom,msm-id = <199 0x20000>;
 
@@ -115,7 +116,7 @@
 };
 
 &rpm_requests {
-	pm8226-regulators {
+	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
 
 		pm8226_s3: s3 {
@@ -299,8 +300,8 @@
 		input-enable;
 	};
 
-	touch_pins: touch {
-		irq {
+	touch_pins: touch-state {
+		irq-pins {
 			pins = "gpio17";
 			function = "gpio";
 
@@ -309,7 +310,7 @@
 			input-enable;
 		};
 
-		reset {
+		reset-pins {
 			pins = "gpio16";
 			function = "gpio";
 
diff --git a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..1c52337af560
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1";
+	compatible = "samsung,matisse-wifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <1280>;
+			height = <800>;
+			stride = <(1280 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+			interrupts = <&tlmm 110 IRQ_TYPE_EDGE_FALLING>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en_default_state>;
+	};
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		/delete-node/ smem@3000000;
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default_state>;
+
+		st,drdy-int-pin = <1>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&muic_int_default_state>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+
+		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&reg_tsp_1p8v>;
+		vdda-supply = <&reg_tsp_3p3v>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio73";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 573e4dc66bb0..7a4c59e04af6 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -81,931 +81,899 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
 	};
+};
 
-	soc {
-		pinctrl@800000 {
-			/* eMMC pins, all 8 data lines connected */
-			dragon_sdcc1_pins: sdcc1 {
-				mux {
-					pins = "gpio159", "gpio160", "gpio161",
-					     "gpio162", "gpio163", "gpio164",
-					     "gpio165", "gpio166", "gpio167",
-					     "gpio168";
-					     function = "sdc1";
-				};
-				clk {
-					pins = "gpio167"; /* SDC1 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio168"; /* SDC1 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC1 D0 to D7 */
-					pins = "gpio159", "gpio160", "gpio161", "gpio162",
-					     "gpio163", "gpio164", "gpio165", "gpio166";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
+&ebi2 {
+	/* The EBI2 will instantiate first, then populate its children */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_ebi2_pins>;
+	status = "okay";
 
-			/*
-			 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
-			 * configuration.
-			 */
-			dragon_sdcc3_pins: sdcc3 {
-				clk {
-					pins = "sdc3_clk";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				cmd {
-					pins = "sdc3_cmd";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-				data {
-					pins = "sdc3_data";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-			};
+	/*
+	 * An on-board SMSC LAN9221 chip for "debug ethernet",
+	 * which is actually just an ordinary ethernet on the
+	 * EBI2. This has a 25MHz chrystal next to it, so no
+	 * clocking is needed.
+	 */
+	ethernet@2,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <2 0x0 0x100>;
+		/*
+		 * The second interrupt is the PME interrupt
+		 * for network wakeup, connected to the TLMM.
+		 */
+		interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+				    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		vdd33a-supply = <&dragon_veth>;
+		vddvario-supply = <&dragon_vario>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ethernet_gpios>;
+		phy-mode = "mii";
+		reg-io-width = <2>;
+		smsc,force-external-phy;
+		smsc,irq-push-pull;
+
+		/*
+		 * SLOW chipselect config
+		 * Delay 9 cycles (140ns@64MHz) between SMSC
+		 * LAN9221 Ethernet controller reads and writes
+		 * on CS2.
+		 */
+		qcom,xmem-recovery-cycles = <0>;
+		qcom,xmem-write-hold-cycles = <3>;
+		qcom,xmem-write-delta-cycles = <31>;
+		qcom,xmem-read-delta-cycles = <28>;
+		qcom,xmem-write-wait-cycles = <9>;
+		qcom,xmem-read-wait-cycles = <9>;
+	};
+};
 
-			/* Second SD card slot pins */
-			dragon_sdcc5_pins: sdcc5 {
-				mux {
-					pins = "gpio95", "gpio96", "gpio97",
-					    "gpio98", "gpio99", "gpio100";
-					function = "sdc5";
-				};
-				clk {
-					pins = "gpio97"; /* SDC5 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio95"; /* SDC5 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC5 D0 to D3 */
-					pins = "gpio96", "gpio98", "gpio99", "gpio100";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-			dragon_gsbi3_i2c_pins: gsbi3_i2c {
-				mux {
-					pins = "gpio43", "gpio44";
-					function = "gsbi3";
-				};
-				pinconf {
-					pins = "gpio43", "gpio44";
-					drive-strength = <8>;
-					/* These have external pull-up 2.2kOhm to 1.8V */
-					bias-disable;
-				};
-			};
+&gsbi3_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,cy8ctma340";
+		reg = <0x24>;
+		/* Certainly we can do at least 400 kHz */
+		clock-frequency = <400000>;
+		/* IRQ on GPIO61 called /CTP_INT */
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * The I2C bus is using a PCA9306 level translator from L16A
+		 * to L2B so these two voltages are needed and L16A is
+		 * kind of the IO voltage, however L16Aisn't really fed to
+		 * the TMA340, which relies entirely on L2B (PM8901 L2).
+		 */
+		vcpin-supply = <&pm8058_l16>;
+		vdd-supply = <&pm8901_l2>;
+		/* GPIO58, called WAKE_CTP */
+		reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		active-interval-ms = <0>;
+		touch-timeout-ms = <255>;
+		lowpower-interval-ms = <10>;
+		bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_tma340_gpios>;
+	};
+};
 
-			dragon_gsbi8_i2c_pins: gsbi8_i2c {
-				mux {
-					pins = "gpio64", "gpio65";
-					function = "gsbi8";
-				};
-				pinconf {
-					pins = "gpio64", "gpio65";
-					drive-strength = <16>;
-					/* These have external pull-up 2.2kOhm to 1.8V */
-					bias-disable;
-				};
-			};
+&gsbi8 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-			dragon_gsbi12_i2c_pins: gsbi12_i2c {
-				mux {
-					pins = "gpio115", "gpio116";
-					function = "gsbi12";
-				};
-				pinconf {
-					pins = "gpio115", "gpio116";
-					drive-strength = <16>;
-					/* These have external pull-up 4.7kOhm to 1.8V */
-					bias-disable;
-				};
-			};
+&gsbi8_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+	status = "okay";
+
+	eeprom@52 {
+		/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		vcc-supply = <&pm8058_s3>;
+		pagesize = <64>;
+	};
+	wm8903: wm8903@1a {
+		/* This Woolfson Micro device has an unrouted interrupt line */
+		compatible = "wlf,wm8903";
+		reg = <0x1a>;
+
+		AVDD-supply = <&pm8058_l16>;
+		CPVDD-supply = <&pm8058_l16>;
+		DBVDD-supply = <&pm8058_s3>;
+		DCVDD-supply = <&pm8058_l0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		micdet-cfg = <0>;
+		micdet-delay = <100>;
+		gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+	};
+};
 
-			/* Primary serial port uart 0 pins */
-			dragon_gsbi12_serial_pins: gsbi12_serial {
-				mux {
-					pins = "gpio117", "gpio118";
-					function = "gsbi12";
-				};
-				tx {
-					pins = "gpio117";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				rx {
-					pins = "gpio118";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-			};
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
 
-			dragon_ebi2_pins: ebi2 {
-				/*
-				 * Pins used by EBI2 on the Dragonboard, actually only
-				 * CS2 is used by a real peripheral. CS0 is just
-				 * routed to a test point.
-				 */
-				mux0 {
-					pins =
-					    /* "gpio39", CS1A_N this is not good to mux */
-					    "gpio40", /* CS2A_N */
-					    "gpio134"; /* CS0_N testpoint TP29 */
-					function = "ebi2cs";
-				};
-				mux1 {
-					pins =
-					    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
-					    "gpio123", "gpio124", "gpio125", "gpio126",
-					    "gpio127", "gpio128", "gpio129", "gpio130",
-					    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
-					    "gpio135", "gpio136", "gpio137", "gpio138",
-					    "gpio139", "gpio140", "gpio141", "gpio142",
-					    "gpio143", "gpio144", "gpio145", "gpio146",
-					    "gpio147", "gpio148", "gpio149", "gpio150",
-					    "gpio151", /* EBI2_OE_N */
-					    "gpio153", /* EBI2_ADV */
-					    "gpio157"; /* EBI2_WE_N */
-					function = "ebi2";
-				};
-			};
+&gsbi12_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+	status = "okay";
+};
 
-			/* Interrupt line for the KXSD9 accelerometer */
-			dragon_kxsd9_gpios: kxsd9 {
-				irq {
-					pins = "gpio57"; /* IRQ line */
-					bias-pull-up;
-				};
-			};
+&gsbi12_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+	status = "okay";
+
+	ak8975@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ak8975_gpios>;
+		vid-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+	};
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_bmp085_gpios>;
+		vddd-supply = <&pm8058_lvs0>; // 1.8V
+		vdda-supply = <&pm8058_l14>; // 2.85V
+	};
+	mpu3050@68 {
+		compatible = "invensense,mpu3050";
+		reg = <0x68>;
+		/*
+		 * GPIO17 is pulled high by a 10k
+		 * resistor to VLOGIC so needs to be
+		 * active low/falling edge.
+		 */
+		interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_mpu3050_gpios>;
+		vlogic-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
 
-			dragon_tma340_gpios: tma340 {
-				reset {
-					/* RESET line, TS_ATTN, WAKE_CTP */
-					pins = "gpio58";
-					function = "gpio";
-					drive-strength = <6>;
-					bias-disable;
-				};
-				irq {
-					pins = "gpio61"; /* IRQ line */
-					function = "gpio";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
+		/*
+		 * The MPU-3050 acts as a hub for the
+		 * accelerometer.
+		 */
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			kxsd9@18 {
+				compatible = "kionix,kxsd9";
+				reg = <0x18>;
+				interrupt-parent = <&tlmm>;
+				interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_kxsd9_gpios>;
+				iovdd-supply = <&pm8058_lvs0>; // 1.8V
+				vdd-supply = <&pm8058_l14>; // 2.85V
 			};
 		};
+	};
+};
 
-		qcom,ssbi@500000 {
-			pmic@0 {
-				keypad@148 {
-					linux,keymap = <
-					MATRIX_KEY(0, 0, KEY_MENU)
-					MATRIX_KEY(0, 2, KEY_1)
-					MATRIX_KEY(0, 3, KEY_4)
-					MATRIX_KEY(0, 4, KEY_7)
-					MATRIX_KEY(1, 0, KEY_UP)
-					MATRIX_KEY(1, 1, KEY_LEFT)
-					MATRIX_KEY(1, 2, KEY_DOWN)
-					MATRIX_KEY(1, 3, KEY_5)
-					MATRIX_KEY(1, 3, KEY_8)
-					MATRIX_KEY(2, 0, KEY_HOME)
-					MATRIX_KEY(2, 1, KEY_REPLY)
-					MATRIX_KEY(2, 2, KEY_2)
-					MATRIX_KEY(2, 3, KEY_6)
-					MATRIX_KEY(3, 0, KEY_VOLUMEUP)
-					MATRIX_KEY(3, 1, KEY_RIGHT)
-					MATRIX_KEY(3, 2, KEY_3)
-					MATRIX_KEY(3, 3, KEY_9)
-					MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
-					MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
-					MATRIX_KEY(4, 1, KEY_BACK)
-					MATRIX_KEY(4, 2, KEY_CAMERA)
-					MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
-					>;
-					keypad,num-rows = <6>;
-					keypad,num-columns = <5>;
-				};
-
-				gpio@150 {
-					dragon_ethernet_gpios: ethernet-state {
-						pinconf {
-							pins = "gpio7";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_bmp085_gpios: bmp085-state {
-						pinconf {
-							pins = "gpio16";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_mpu3050_gpios: mpu3050-state {
-						pinconf {
-							pins = "gpio17";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc3_gpios: sdcc3-state {
-						pinconf {
-							pins = "gpio22";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc5_gpios: sdcc5-state {
-						pinconf {
-							pins = "gpio26";
-							function = "normal";
-							input-enable;
-							bias-pull-up;
-							qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_ak8975_gpios: ak8975-state {
-						pinconf {
-							pins = "gpio33";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_cm3605_gpios: cm3605-state {
-						/* Pin 34 connected to the proxy IRQ */
-						gpio34-pins {
-							pins = "gpio34";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-						/* Pin 35 connected to ASET */
-						gpio35-pins {
-							pins = "gpio35";
-							function = "normal";
-							output-high;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_veth_gpios: veth-state {
-						pinconf {
-							pins = "gpio40";
-							function = "normal";
-							bias-disable;
-							drive-push-pull;
-						};
-					};
-				};
-
-				mpps@50 {
-					dragon_cm3605_mpps: cm3605-mpps-state {
-						mpp5 {
-							pins = "mpp5";
-							function = "analog";
-							input-enable;
-							bias-high-impedance;
-							/* Let's use channel 5 */
-							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-				};
-
-				xoadc@197 {
-					/* Reference voltage 2.2 V */
-					xoadc-ref-supply = <&pm8058_l18>;
-
-					/* Board-specific channels */
-					mpp5@5 {
-						/* Connected to AOUT of ALS sensor */
-						reg = <0x00 0x05>;
-					};
-					mpp6@6 {
-						/* Connected to test point TP43 */
-						reg = <0x00 0x06>;
-					};
-					mpp7@7 {
-						/* Connected to battery thermistor */
-						reg = <0x00 0x07>;
-					};
-					mpp8@8 {
-						/* Connected to battery ID detector */
-						reg = <0x00 0x08>;
-					};
-					mpp9@9 {
-						/* Connected to XO thermistor */
-						reg = <0x00 0x09>;
-					};
-				};
-
-				led@48 {
-					/*
-					 * The keypad LED @0x48 is routed to
-					 * the sensor board where it is
-					 * connected to an infrared LED
-					 * SFH4650 (60mW, @850nm) next to the
-					 * ambient light and proximity sensor
-					 * Capella Microsystems CM3605.
-					 */
-					compatible = "qcom,pm8058-keypad-led";
-					reg = <0x48>;
-					label = "pm8058:infrared:proximitysensor";
-					default-state = "off";
-					linux,default-trigger = "cm3605";
-				};
-				led@131 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x131>;
-					label = "pm8058:red";
-					color = <LED_COLOR_ID_RED>;
-					default-state = "off";
-				};
-				led@132 {
-					/*
-					 * This is actually green too on my
-					 * board, but documented as yellow.
-					 */
-					compatible = "qcom,pm8058-led";
-					reg = <0x132>;
-					label = "pm8058:yellow";
-					color = <LED_COLOR_ID_YELLOW>;
-					default-state = "off";
-					linux,default-trigger = "mmc0";
-				};
-				led@133 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x133>;
-					label = "pm8058:green";
-					function = LED_FUNCTION_HEARTBEAT;
-					color = <LED_COLOR_ID_GREEN>;
-					default-state = "on";
-					linux,default-trigger = "heartbeat";
-				};
-			};
+&pm8058_gpio {
+	dragon_ethernet_gpios: ethernet-state {
+		pinconf {
+			pins = "gpio7";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_bmp085_gpios: bmp085-state {
+		pinconf {
+			pins = "gpio16";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_mpu3050_gpios: mpu3050-state {
+		pinconf {
+			pins = "gpio17";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc3_gpios: sdcc3-state {
+		pinconf {
+			pins = "gpio22";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc5_gpios: sdcc5-state {
+		pinconf {
+			pins = "gpio26";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_ak8975_gpios: ak8975-state {
+		pinconf {
+			pins = "gpio33";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_cm3605_gpios: cm3605-state {
+		/* Pin 34 connected to the proxy IRQ */
+		gpio34-pins {
+			pins = "gpio34";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+		/* Pin 35 connected to ASET */
+		gpio35-pins {
+			pins = "gpio35";
+			function = "normal";
+			output-high;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_veth_gpios: veth-state {
+		pinconf {
+			pins = "gpio40";
+			function = "normal";
+			bias-disable;
+			drive-push-pull;
 		};
+	};
+};
 
-		gsbi@16200000 {
-			qcom,mode = <GSBI_PROT_I2C>;
-			status = "okay";
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_MENU)
+		MATRIX_KEY(0, 2, KEY_1)
+		MATRIX_KEY(0, 3, KEY_4)
+		MATRIX_KEY(0, 4, KEY_7)
+		MATRIX_KEY(1, 0, KEY_UP)
+		MATRIX_KEY(1, 1, KEY_LEFT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_5)
+		MATRIX_KEY(1, 3, KEY_8)
+		MATRIX_KEY(2, 0, KEY_HOME)
+		MATRIX_KEY(2, 1, KEY_REPLY)
+		MATRIX_KEY(2, 2, KEY_2)
+		MATRIX_KEY(2, 3, KEY_6)
+		MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(3, 1, KEY_RIGHT)
+		MATRIX_KEY(3, 2, KEY_3)
+		MATRIX_KEY(3, 3, KEY_9)
+		MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+		MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+		MATRIX_KEY(4, 1, KEY_BACK)
+		MATRIX_KEY(4, 2, KEY_CAMERA)
+		MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+	>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
 
-			gsbi3_i2c: i2c@16280000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
-				status = "okay";
-
-				touchscreen@24 {
-					compatible = "cypress,cy8ctma340";
-					reg = <0x24>;
-					/* Certainly we can do at least 400 kHz */
-					clock-frequency = <400000>;
-					/* IRQ on GPIO61 called /CTP_INT */
-					interrupt-parent = <&tlmm>;
-					interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
-					/*
-					 * The I2C bus is using a PCA9306 level translator from L16A
-					 * to L2B so these two voltages are needed and L16A is
-					 * kind of the IO voltage, however L16Aisn't really fed to
-					 * the TMA340, which relies entirely on L2B (PM8901 L2).
-					 */
-					vcpin-supply = <&pm8058_l16>;
-					vdd-supply = <&pm8901_l2>;
-					/* GPIO58, called WAKE_CTP */
-					reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
-					touchscreen-size-x = <480>;
-					touchscreen-size-y = <800>;
-					active-interval-ms = <0>;
-					touch-timeout-ms = <255>;
-					lowpower-interval-ms = <10>;
-					bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_tma340_gpios>;
-				};
-			};
+&pm8058_led48 {
+	/*
+	 * The keypad LED @0x48 is routed to
+	 * the sensor board where it is
+	 * connected to an infrared LED
+	 * SFH4650 (60mW, @850nm) next to the
+	 * ambient light and proximity sensor
+	 * Capella Microsystems CM3605.
+	 */
+	label = "pm8058:infrared:proximitysensor";
+	default-state = "off";
+	linux,default-trigger = "cm3605";
+	status = "okay";
+};
+
+&pm8058_led131 {
+	label = "pm8058:red";
+	color = <LED_COLOR_ID_RED>;
+	default-state = "off";
+	status = "okay";
+};
+
+&pm8058_led132 {
+	/*
+	 * This is actually green too on my
+	 * board, but documented as yellow.
+	 */
+	label = "pm8058:yellow";
+	color = <LED_COLOR_ID_YELLOW>;
+	default-state = "off";
+	linux,default-trigger = "mmc0";
+	status = "okay";
+};
+
+&pm8058_led133 {
+	label = "pm8058:green";
+	function = LED_FUNCTION_HEARTBEAT;
+	color = <LED_COLOR_ID_GREEN>;
+	default-state = "on";
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pm8058_mpps {
+	dragon_cm3605_mpps: cm3605-mpps-state {
+		mpp5 {
+			pins = "mpp5";
+			function = "analog";
+			input-enable;
+			bias-high-impedance;
+			/* Let's use channel 5 */
+			qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+			power-source = <PM8058_GPIO_S3>;
 		};
+	};
+};
 
-		gsbi@19800000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
+&rpm {
+	/*
+	 * Set up of the PMIC RPM regulators for this board
+	 * PM8901 supplies "preliminary regulators" whatever
+	 * that means
+	 */
+	pm8901-regulators {
+		vdd_l0-supply = <&pm8901_s4>;
+		vdd_l1-supply = <&vph>;
+		vdd_l2-supply = <&vph>;
+		vdd_l3-supply = <&vph>;
+		vdd_l4-supply = <&vph>;
+		vdd_l5-supply = <&vph>;
+		vdd_l6-supply = <&vph>;
+		/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		lvs0_in-supply = <&pm8058_s3>;
+		lvs1_in-supply = <&pm8901_s4>;
+		lvs2_in-supply = <&pm8058_l0>;
+		lvs3_in-supply = <&pm8058_s2>;
+		mvs_in-supply = <&pm8058_s3>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l2 {
+			/* TMA340 requires strictly 3.3V */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
 
-			i2c@19880000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
-
-				eeprom@52 {
-					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					vcc-supply = <&pm8058_s3>;
-					pagesize = <64>;
-				};
-				wm8903: wm8903@1a {
-					/* This Woolfson Micro device has an unrouted interrupt line */
-					compatible = "wlf,wm8903";
-					reg = <0x1a>;
-
-					AVDD-supply = <&pm8058_l16>;
-					CPVDD-supply = <&pm8058_l16>;
-					DBVDD-supply = <&pm8058_s3>;
-					DCVDD-supply = <&pm8058_l0>;
-
-					gpio-controller;
-					#gpio-cells = <2>;
-
-					micdet-cfg = <0>;
-					micdet-delay = <100>;
-					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
-				};
-			};
+		/* s0 and s1 are SAW regulators controlled over SPM */
+		s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
 		};
 
-		gsbi@19c00000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
+		/* LVS0 thru 3 and mvs are just switches */
+		lvs0 {
+			regulator-always-on;
+		};
+		lvs1 { };
+		lvs2 { };
+		lvs3 { };
+		mvs { };
 
-			serial@19c40000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_serial_pins>;
-			};
+	};
 
-			i2c@19c80000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
-
-				ak8975@c {
-					compatible = "asahi-kasei,ak8975";
-					reg = <0x0c>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <33 IRQ_TYPE_EDGE_RISING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_ak8975_gpios>;
-					vid-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-				};
-				bmp085@77 {
-					compatible = "bosch,bmp085";
-					reg = <0x77>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <16 IRQ_TYPE_EDGE_RISING>;
-					reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_bmp085_gpios>;
-					vddd-supply = <&pm8058_lvs0>; // 1.8V
-					vdda-supply = <&pm8058_l14>; // 2.85V
-				};
-				mpu3050@68 {
-					compatible = "invensense,mpu3050";
-					reg = <0x68>;
-					/*
-					 * GPIO17 is pulled high by a 10k
-					 * resistor to VLOGIC so needs to be
-					 * active low/falling edge.
-					 */
-					interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_mpu3050_gpios>;
-					vlogic-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-
-					/*
-					 * The MPU-3050 acts as a hub for the
-					 * accelerometer.
-					 */
-					i2c-gate {
-						#address-cells = <1>;
-						#size-cells = <0>;
-
-						kxsd9@18 {
-							compatible = "kionix,kxsd9";
-							reg = <0x18>;
-							interrupt-parent = <&tlmm>;
-							interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
-							pinctrl-names = "default";
-							pinctrl-0 = <&dragon_kxsd9_gpios>;
-							iovdd-supply = <&pm8058_lvs0>; // 1.8V
-							vdd-supply = <&pm8058_l14>; // 2.85V
-						};
-					};
-				};
-			};
+	pm8058-regulators {
+		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+		vdd_l2_l11_l12-supply = <&vph>;
+		vdd_l3_l4_l5-supply = <&vph>;
+		vdd_l6_l7-supply = <&vph>;
+		vdd_l8-supply = <&vph>;
+		vdd_l9-supply = <&vph>;
+		vdd_l10-supply = <&vph>;
+		vdd_l13_l16-supply = <&pm8058_s4>;
+		vdd_l14_l15-supply = <&vph>;
+		vdd_l17_l18-supply = <&vph>;
+		vdd_l19_l20-supply = <&vph>;
+		vdd_l21-supply = <&pm8058_s3>;
+		vdd_l22-supply = <&pm8058_s3>;
+		vdd_l23_l24_l25-supply = <&pm8058_s3>;
+		vdd_s0-supply = <&vph>;
+		vdd_s1-supply = <&vph>;
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		vdd_ncp-supply = <&vph>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3600000>;
+			bias-pull-down;
+		};
+		l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3050000>;
+			bias-pull-down;
+		};
+		l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l10 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l11 {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+		l12 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+		l13 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			bias-pull-down;
+		};
+		l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l17 {
+			// 1.5V according to schematic
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l18 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+		l19 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			bias-pull-down;
+		};
+		l20 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l21 {
+			// 1.1 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l22 {
+			// 1.2 V according to schematic
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+		l23 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l24 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l25 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
 		};
 
-		external-bus@1a100000 {
-			/* The EBI2 will instantiate first, then populate its children */
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&dragon_ebi2_pins>;
-
-			/*
-			 * An on-board SMSC LAN9221 chip for "debug ethernet",
-			 * which is actually just an ordinary ethernet on the
-			 * EBI2. This has a 25MHz chrystal next to it, so no
-			 * clocking is needed.
-			 */
-			ethernet@2,0 {
-				compatible = "smsc,lan9221", "smsc,lan9115";
-				reg = <2 0x0 0x100>;
-				/*
-				 * The second interrupt is the PME interrupt
-				 * for network wakeup, connected to the TLMM.
-				 */
-				interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
-						    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
-				reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
-				vdd33a-supply = <&dragon_veth>;
-				vddvario-supply = <&dragon_vario>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_ethernet_gpios>;
-				phy-mode = "mii";
-				reg-io-width = <2>;
-				smsc,force-external-phy;
-				smsc,irq-push-pull;
-
-				/*
-				 * SLOW chipselect config
-				 * Delay 9 cycles (140ns@64MHz) between SMSC
-				 * LAN9221 Ethernet controller reads and writes
-				 * on CS2.
-				 */
-				qcom,xmem-recovery-cycles = <0>;
-				qcom,xmem-write-hold-cycles = <3>;
-				qcom,xmem-write-delta-cycles = <31>;
-				qcom,xmem-read-delta-cycles = <28>;
-				qcom,xmem-write-wait-cycles = <9>;
-				qcom,xmem-read-wait-cycles = <9>;
-			};
+		s0 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1325000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s1 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1250000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s2 {
+			// 1.3 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
 		};
 
-		rpm@104000 {
-			/*
-			 * Set up of the PMIC RPM regulators for this board
-			 * PM8901 supplies "preliminary regulators" whatever
-			 * that means
-			 */
-			pm8901-regulators {
-				vdd_l0-supply = <&pm8901_s4>;
-				vdd_l1-supply = <&vph>;
-				vdd_l2-supply = <&vph>;
-				vdd_l3-supply = <&vph>;
-				vdd_l4-supply = <&vph>;
-				vdd_l5-supply = <&vph>;
-				vdd_l6-supply = <&vph>;
-				/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				lvs0_in-supply = <&pm8058_s3>;
-				lvs1_in-supply = <&pm8901_s4>;
-				lvs2_in-supply = <&pm8058_l0>;
-				lvs3_in-supply = <&pm8058_s2>;
-				mvs_in-supply = <&pm8058_s3>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l2 {
-					/* TMA340 requires strictly 3.3V */
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-
-				/* s0 and s1 are SAW regulators controlled over SPM */
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* LVS0 thru 3 and mvs are just switches */
-				lvs0 {
-					regulator-always-on;
-				};
-				lvs1 { };
-				lvs2 { };
-				lvs3 { };
-				mvs { };
+		/* LVS0 and LVS1 are just switches */
+		lvs0 {
+			bias-pull-down;
+		};
+		lvs1 {
+			bias-pull-down;
+		};
 
-			};
+		ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
 
-			pm8058-regulators {
-				vdd_l0_l1_lvs-supply = <&pm8058_s3>;
-				vdd_l2_l11_l12-supply = <&vph>;
-				vdd_l3_l4_l5-supply = <&vph>;
-				vdd_l6_l7-supply = <&vph>;
-				vdd_l8-supply = <&vph>;
-				vdd_l9-supply = <&vph>;
-				vdd_l10-supply = <&vph>;
-				vdd_l13_l16-supply = <&pm8058_s4>;
-				vdd_l14_l15-supply = <&vph>;
-				vdd_l17_l18-supply = <&vph>;
-				vdd_l19_l20-supply = <&vph>;
-				vdd_l21-supply = <&pm8058_s3>;
-				vdd_l22-supply = <&pm8058_s3>;
-				vdd_l23_l24_l25-supply = <&pm8058_s3>;
-				vdd_s0-supply = <&vph>;
-				vdd_s1-supply = <&vph>;
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				vdd_ncp-supply = <&vph>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l2 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3600000>;
-					bias-pull-down;
-				};
-				l7 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l8 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <3050000>;
-					bias-pull-down;
-				};
-				l9 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l10 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l11 {
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					bias-pull-down;
-				};
-				l12 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-				l13 {
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					bias-pull-down;
-				};
-				l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-				};
-				l15 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l16 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l17 {
-					// 1.5V according to schematic
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l18 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-				l19 {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <2500000>;
-					bias-pull-down;
-				};
-				l20 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l21 {
-					// 1.1 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l22 {
-					// 1.2 V according to schematic
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-				l23 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l24 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l25 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				s0 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1325000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s1 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1250000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s2 {
-					// 1.3 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				/* LVS0 and LVS1 are just switches */
-				lvs0 {
-					bias-pull-down;
-				};
-				lvs1 {
-					bias-pull-down;
-				};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
+/* Internal 3.69 GiB eMMC */
+&sdcc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc1_pins>;
+	vmmc-supply = <&pm8901_l5>;
+	vqmmc-supply = <&pm8901_lvs0>;
+	status = "okay";
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+	/* Enable SSBI GPIO 22 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+	cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	status = "okay";
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+	/* Enable SSBI GPIO 26 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+	cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	vqmmc-supply = <&dragon_vio_txb>;
+	status = "okay";
+};
+
+&tlmm {
+	/* eMMC pins, all 8 data lines connected */
+	dragon_sdcc1_pins: sdcc1-state {
+		clk-pins {
+			pins = "gpio167"; /* SDC1 CLK */
+			function = "sdc1";
+			drive-strength = <16>;
+			bias-disable;
 		};
-		amba {
-			/* Internal 3.69 GiB eMMC */
-			mmc@12400000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc1_pins>;
-				vmmc-supply = <&pm8901_l5>;
-				vqmmc-supply = <&pm8901_lvs0>;
-			};
+		cmd-pins {
+			pins = "gpio168"; /* SDC1 CMD */
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC1 D0 to D7 */
+			pins = "gpio159", "gpio160", "gpio161", "gpio162",
+			     "gpio163", "gpio164", "gpio165", "gpio166";
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
 
-			/* External micro SD card, directly connected, pulled up to 2.85 V */
-			mmc@12180000 {
-				status = "okay";
-				/* Enable SSBI GPIO 22 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
-				cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-			};
+	/*
+	 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+	 * configuration.
+	 */
+	dragon_sdcc3_pins: sdcc3-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
 
-			/*
-			 * Second external micro SD card, using two TXB104RGYR levelshifters
-			 * to lift from 1.8 V to 2.85 V
-			 */
-			mmc@12200000 {
-				status = "okay";
-				/* Enable SSBI GPIO 26 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
-				cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-				vqmmc-supply = <&dragon_vio_txb>;
-			};
+	/* Second SD card slot pins */
+	dragon_sdcc5_pins: sdcc5-state {
+		clk-pins {
+			pins = "gpio97"; /* SDC5 CLK */
+			function = "sdc5";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio95"; /* SDC5 CMD */
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC5 D0 to D3 */
+			pins = "gpio96", "gpio98", "gpio99", "gpio100";
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
 		};
 	};
+
+	dragon_gsbi3_i2c_pins: gsbi3-i2c-state {
+		pins = "gpio43", "gpio44";
+		function = "gsbi3";
+		drive-strength = <8>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi8_i2c_pins: gsbi8-i2c-state {
+		pins = "gpio64", "gpio65";
+		function = "gsbi8";
+		drive-strength = <16>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi12_i2c_pins: gsbi12-i2c-state {
+		pins = "gpio115", "gpio116";
+		function = "gsbi12";
+		drive-strength = <16>;
+		/* These have external pull-up 4.7kOhm to 1.8V */
+		bias-disable;
+	};
+
+	/* Primary serial port uart 0 pins */
+	dragon_gsbi12_serial_pins: gsbi12-serial-state {
+		tx-pins {
+			pins = "gpio117";
+			function = "gsbi12";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		rx-pins {
+			pins = "gpio118";
+			function = "gsbi12";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_ebi2_pins: ebi2-state {
+		/*
+		 * Pins used by EBI2 on the Dragonboard, actually only
+		 * CS2 is used by a real peripheral. CS0 is just
+		 * routed to a test point.
+		 */
+		mux0-pins {
+			pins =
+			    /* "gpio39", CS1A_N this is not good to mux */
+			    "gpio40", /* CS2A_N */
+			    "gpio134"; /* CS0_N testpoint TP29 */
+			function = "ebi2cs";
+		};
+		mux1-pins {
+			pins =
+			    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+			    "gpio123", "gpio124", "gpio125", "gpio126",
+			    "gpio127", "gpio128", "gpio129", "gpio130",
+			    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+			    "gpio135", "gpio136", "gpio137", "gpio138",
+			    "gpio139", "gpio140", "gpio141", "gpio142",
+			    "gpio143", "gpio144", "gpio145", "gpio146",
+			    "gpio147", "gpio148", "gpio149", "gpio150",
+			    "gpio151", /* EBI2_OE_N */
+			    "gpio153", /* EBI2_ADV */
+			    "gpio157"; /* EBI2_WE_N */
+			function = "ebi2";
+		};
+	};
+
+	/* Interrupt line for the KXSD9 accelerometer */
+	dragon_kxsd9_gpios: kxsd9-state {
+		pins = "gpio57"; /* IRQ line */
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	dragon_tma340_gpios: tma340-state {
+		reset-pins {
+			/* RESET line, TS_ATTN, WAKE_CTP */
+			pins = "gpio58";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-disable;
+		};
+		irq-pins {
+			pins = "gpio61"; /* IRQ line */
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&xoadc {
+	/* Reference voltage 2.2 V */
+	xoadc-ref-supply = <&pm8058_l18>;
+
+	/* Board-specific channels */
+	mpp5@5 {
+		/* Connected to AOUT of ALS sensor */
+		reg = <0x00 0x05>;
+	};
+	mpp6@6 {
+		/* Connected to test point TP43 */
+		reg = <0x00 0x06>;
+	};
+	mpp7@7 {
+		/* Connected to battery thermistor */
+		reg = <0x00 0x07>;
+	};
+	mpp8@8 {
+		/* Connected to battery ID detector */
+		reg = <0x00 0x08>;
+	};
+	mpp9@9 {
+		/* Connected to XO thermistor */
+		reg = <0x00 0x09>;
+	};
 };
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index fee278e32cb6..bf2fb0f70fe4 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -6,6 +6,7 @@
 / {
 	model = "Asus Nexus7(flo)";
 	compatible = "asus,nexus7-flo", "qcom,apq8064";
+	chassis-type = "tablet";
 
 	aliases {
 		serial0 = &gsbi7_serial;
@@ -30,7 +31,7 @@
 		};
 	};
 
-	ext_3p3v: regulator-fixed@1 {
+	ext_3p3v: regulator-ext-3p3v {
 		compatible = "regulator-fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -57,302 +58,291 @@
 	};
 
 	soc {
-		rpm@108000 {
-			regulators {
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vin_lvs2-supply = <&pm8921_s1>;
-
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				vdd_ncp-supply = <&pm8921_l6>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				/* msm otg HSUSB_VDDCX */
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				/*
-				 * msm_sdcc.1-sdc-vdd_io
-				 * tabla2x-slim-CDC_VDDA_RX
-				 * tabla2x-slim-CDC_VDDA_TX
-				 * tabla2x-slim-CDC_VDD_CP
-				 * tabla2x-slim-VDDIO_CDC
-				 */
-				s4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-					regulator-always-on;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				/* mipi_dsi.1-dsi1_pll_vdda */
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-				};
-
-				/* msm_otg-HSUSB_3p3 */
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				/* msm_otg-HSUSB_1p8 */
-				l4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/* msm_sdcc.1-sdc_vdd */
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				/* mipi_dsi.1-dsi1_avdd */
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				/* pwm_power for backlight */
-				l17 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				/* camera, qdsp6 */
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/*
-				 * tabla2x-slim-CDC_VDDA_A_1P2V
-				 * tabla2x-slim-VDDD_CDC_D
-				 */
-				l25 {
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-				/*
-				 * mipi_dsi.1-dsi1_vddio
-				 * pil_riva-pll_vdd
-				 */
-				lvs7 {
-					bias-pull-down;
-				};
-			};
-		};
+		sram@2a03f000 {
+			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
+			reg = <0x2a03f000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
 
-		mdp@5100000 {
-			status = "okay";
-			ports {
-				port@1 {
-					mdp_dsi1_out: endpoint {
-						remote-endpoint = <&dsi0_in>;
-					};
-				};
+				mode-normal = <0x77665501>;
+				mode-bootloader = <0x77665500>;
+				mode-recovery = <0x77665502>;
 			};
 		};
+	};
+};
 
-		dsi0: dsi@4700000 {
-			status = "okay";
-			vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
-			vdd-supply = <&pm8921_l8>;
-			vddio-supply = <&pm8921_lvs7>;
-			avdd-supply = <&pm8921_l11>;
-
-			panel@0 {
-				reg = <0>;
-				compatible = "jdi,lt070me05000";
-
-				vddp-supply = <&pm8921_l17>;
-				iovcc-supply = <&pm8921_lvs7>;
-
-				enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
-				reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
-				dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-			ports {
-				port@0 {
-					dsi0_in: endpoint {
-						remote-endpoint = <&mdp_dsi1_out>;
-					};
-				};
-
-				port@1 {
-					dsi0_out: endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
+&dsi0 {
+	vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+	vdd-supply = <&pm8921_l8>;
+	vddio-supply = <&pm8921_lvs7>;
+	avdd-supply = <&pm8921_l11>;
+	status = "okay";
+
+	panel@0 {
+		reg = <0>;
+		compatible = "jdi,lt070me05000";
+
+		vddp-supply = <&pm8921_l17>;
+		iovcc-supply = <&pm8921_lvs7>;
+
+		enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
+		dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
 			};
 		};
+	};
+};
+
+&dsi0_in {
+	remote-endpoint = <&mdp_dsi1_out>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+
+	bq27541@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+	};
+
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	trackpad@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		interrupt-parent = <&tlmm_pinmux>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
 
-		dsi-phy@4700200 {
-			status = "okay";
-			vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&mdp {
+	status = "okay";
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&mdp_dsi1_out {
+	remote-endpoint = <&dsi0_in>;
+};
+
+&rpm {
+	regulators {
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vin_lvs2-supply = <&pm8921_s1>;
+
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		vdd_ncp-supply = <&pm8921_l6>;
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
 		};
 
-		gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c3_pins>;
-				pinctrl-names = "default";
-
-				trackpad@10 {
-					compatible = "elan,ekth3500";
-					reg = <0x10>;
-					interrupt-parent = <&tlmm_pinmux>;
-					interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
-				};
-			};
+		/* msm otg HSUSB_VDDCX */
+		s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
 		};
 
+		/*
+		 * msm_sdcc.1-sdc-vdd_io
+		 * tabla2x-slim-CDC_VDDA_RX
+		 * tabla2x-slim-CDC_VDDA_TX
+		 * tabla2x-slim-CDC_VDD_CP
+		 * tabla2x-slim-VDDIO_CDC
+		 */
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+			regulator-always-on;
+		};
 
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
 
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c1_pins>;
-				pinctrl-names = "default";
+		/* mipi_dsi.1-dsi1_pll_vdda */
+		l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+		};
 
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
+		/* msm_otg-HSUSB_3p3 */
+		l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
 
-				bq27541@55 {
-					compatible = "ti,bq27541";
-					reg = <0x55>;
-				};
+		/* msm_otg-HSUSB_1p8 */
+		l4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
 
-			};
+		/* msm_sdcc.1-sdc_vdd */
+		l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-always-on;
+			bias-pull-down;
 		};
 
-		gsbi@16500000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
 
-			serial@16540000 {
-				status = "okay";
+		/* mipi_dsi.1-dsi1_avdd */
+		l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
 
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
+		/* pwm_power for backlight */
+		l17 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
 		};
 
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-			};
+		/* camera, qdsp6 */
+		l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
 		};
 
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
+		/*
+		 * tabla2x-slim-CDC_VDDA_A_1P2V
+		 * tabla2x-slim-VDDD_CDC_D
+		 */
+		l25 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
 		};
 
-		amba {
-			/* eMMC */
-			mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
+		lvs1 {
+			bias-pull-down;
 		};
 
-		sram@2a03f000 {
-			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
-			reg = <0x2a03f000 0x1000>;
+		lvs4 {
+			bias-pull-down;
+		};
 
-			reboot-mode {
-				compatible = "syscon-reboot-mode";
-				offset = <0x65c>;
+		lvs5 {
+			bias-pull-down;
+		};
 
-				mode-normal = <0x77665501>;
-				mode-bootloader = <0x77665500>;
-				mode-recovery = <0x77665502>;
-			};
+		lvs6 {
+			bias-pull-down;
+		};
+		/*
+		 * mipi_dsi.1-dsi1_vddio
+		 * pil_riva-pll_vdd
+		 */
+		lvs7 {
+			bias-pull-down;
 		};
 	};
 };
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index 529629a0a9dc..d6ecfd8addb7 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -15,232 +15,216 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	pwrseq {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
 	};
 
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
+	/* on board fixed 3.3v supply */
+	v3p3_fixed: regulator-v3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE V3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
 
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-			};
-		};
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
 
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
 
-				eeprom@50 {
-					compatible = "atmel,24c02";
-					reg = <0x50>;
-					pagesize = <32>;
-				};
-			};
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&pcie {
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&v3p3_fixed>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
 		};
+	};
+};
+
+&rpm {
+	regulators {
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
 
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
 		};
 
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
+		s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		/* on board fixed 3.3v supply */
-		v3p3_fixed: v3p3 {
-			compatible = "regulator-fixed";
-			regulator-name = "PCIE V3P3";
-			regulator-min-microvolt = <3300000>;
+		l3 {
+			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
+			bias-pull-down;
+		};
+
+		l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
 		};
 
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios-state {
-						pinconf {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
+		l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
 		};
 
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&v3p3_fixed>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+		lvs6 {
+			bias-pull-down;
 		};
 
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&card_detect>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: mmc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				vqmmc-supply = <&v3p3_fixed>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&v3p3_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	status = "okay";
+	vmmc-supply = <&v3p3_fixed>;
+	vqmmc-supply = <&v3p3_fixed>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
 		};
 	};
 };
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index a7f90217661b..96307550523a 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -22,23 +22,12 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	pwrseq {
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&notify_led>;
 
-		led@1 {
+		led-user1 {
 			label = "apq8064:green:user1";
 			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
@@ -57,326 +46,314 @@
 		};
 	};
 
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
 
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		regulator-type = "voltage";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
 
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-			};
-		};
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-		ext_3p3v: regulator-fixed@1 {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-name = "ext_3p3v";
-			regulator-type = "voltage";
-			startup-delay-us = <0>;
-			gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			regulator-boot-on;
-		};
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
 
-		gsbi3: gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-			};
-		};
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
 
-		gsbi@16300000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			/* CAM I2C MIPI-CSI connector */
-			i2c@16380000 {
-				status = "okay";
-			};
-		};
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	status = "okay";
+};
 
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
 
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
+/* CAM I2C MIPI-CSI connector */
+&gsbi4_i2c {
+	status = "okay";
+};
 
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-		};
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+};
 
-		gsbi@1a200000 {
-			qcom,mode = <GSBI_PROT_SPI>;
-			status = "okay";
-			spi4: spi@1a280000 {
-				status = "okay";
-				num-cs = <1>;
-				cs-gpios = <&tlmm_pinmux 53 0>;
-			};
-		};
+&gsbi5_spi {
+	num-cs = <1>;
+	cs-gpios = <&tlmm_pinmux 53 0>;
+	status = "okay";
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+	status = "okay";
+};
 
-		gsbi@16500000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_UART_W_FC>;
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
 
-			serial@16540000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&hdmi {
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+	hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&hdmi_in {
+	remote-endpoint = <&mdp_dtv_out>;
+};
+
+&hdmi_out {
+	remote-endpoint = <&hdmi_con>;
+};
+
+&hdmi_phy {
+	status = "okay";
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dtv_out {
+	remote-endpoint = <&hdmi_in>;
+};
+
+&pcie {
+	status = "okay";
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&ext_3p3v>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
 		};
+	};
 
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
+	notify_led: nled-state {
+		pinconf {
+			pins = "gpio18";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
 		};
+	};
+};
 
-		sata_phy0: phy@1b400000 {
-			status = "okay";
+&rpm {
+	regulators {
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
 		};
 
-		sata0: sata@29000000 {
-			status = "okay";
-			target-supply = <&pm8921_s4>;
+		s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
 		};
 
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
 		};
 
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
+		l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
 		};
 
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&ext_3p3v>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+		l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
 		};
 
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios-state {
-						pinconf {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-
-					notify_led: nled-state {
-						pinconf {
-							pins = "gpio18";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
+		l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
 		};
 
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
 
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&card_detect>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: mmc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&ext_3p3v>;
-				vqmmc-supply = <&pm8921_lvs1>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
+		l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
 		};
 
-		hdmi-tx@4a00000 {
-			status = "okay";
+		lvs1 {
+			bias-pull-down;
+		};
 
-			core-vdda-supply = <&pm8921_hdmi_switch>;
+		lvs6 {
+			bias-pull-down;
+		};
+	};
+};
 
-			hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+&sata_phy0 {
+	status = "okay";
+};
 
-			ports {
-				port@0 {
-					endpoint {
-						remote-endpoint = <&mdp_dtv_out>;
-					};
-				};
+&sata0 {
+	target-supply = <&pm8921_s4>;
+	status = "okay";
+};
 
-				port@1 {
-					endpoint {
-						remote-endpoint = <&hdmi_con>;
-					};
-				};
-			};
-		};
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
 
-		hdmi-phy@4a00400 {
-			status = "okay";
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
 
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-		};
+/* WLAN */
+&sdcc4 {
+	vmmc-supply = <&ext_3p3v>;
+	vqmmc-supply = <&pm8921_lvs1>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+	status = "okay";
+};
 
-		mdp@5100000 {
-			status = "okay";
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
 
-			ports {
-				port@3 {
-					endpoint {
-						remote-endpoint = <&hdmi_in>;
-					};
-				};
-			};
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
 		};
 	};
 };
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts
index c07c5474750d..9244512b74d1 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -8,6 +8,7 @@
 / {
 	model = "Sony Xperia Z";
 	compatible = "sony,xperia-yuga", "qcom,apq8064";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &gsbi5_serial;
@@ -51,351 +52,338 @@
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi5_uart_pin_a>;
+	status = "okay";
+};
+
+&pm8921_gpio {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio3", "gpio4", "gpio29", "gpio35";
+		function = "normal";
+
+		bias-pull-up;
+		drive-push-pull;
+		input-enable;
+		power-source = <2>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		qcom,pull-up-strength = <0>;
+	};
+};
+
+&riva {
+	pinctrl-names = "default";
+	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+	status = "okay";
+};
+
+&rpm {
+	regulators {
+		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs_1_3_6-supply = <&pm8921_s4>;
+		vin_lvs_4_5_7-supply = <&pm8921_s4>;
+		vin_ncp-supply = <&pm8921_l6>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_l24-supply = <&pm8921_s1>;
+		vin_l25-supply = <&pm8921_s1>;
+		vin_l27-supply = <&pm8921_s7>;
+		vin_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		s8 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+
+		/* PMOS LDO */
+		l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			bias-pull-down;
+		};
 
-	soc {
-		pinctrl@800000 {
-			gsbi5_uart_pin_a: gsbi5-uart-pin-active {
-				rx {
-					pins = "gpio52";
-					function = "gsbi5";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-
-				tx {
-					pins = "gpio51";
-					function = "gsbi5";
-					drive-strength = <4>;
-					bias-disable;
-				};
-			};
-
-
-			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
-				pins = "gpio26";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-
-		rpm@108000 {
-			regulators {
-				vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs_1_3_6-supply = <&pm8921_s4>;
-				vin_lvs_4_5_7-supply = <&pm8921_s4>;
-				vin_ncp-supply = <&pm8921_l6>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_l24-supply = <&pm8921_s1>;
-				vin_l25-supply = <&pm8921_s1>;
-				vin_l27-supply = <&pm8921_s7>;
-				vin_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s8 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-
-				/* PMOS LDO */
-				l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					bias-pull-down;
-				};
-
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l10 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l17 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				l18 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l21 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l22 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				l27 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
-
-				l28 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l29 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs2 {
-					bias-pull-down;
-				};
-
-				lvs3 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-
-				usb-switch {};
-
-				hdmi-switch {};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					gpio_keys_pin_a: gpio-keys-active-state {
-						pins = "gpio3", "gpio4", "gpio29", "gpio35";
-						function = "normal";
-
-						bias-pull-up;
-						drive-push-pull;
-						input-enable;
-						power-source = <2>;
-						qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-						qcom,pull-up-strength = <0>;
-					};
-				};
-			};
-		};
-
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
+		l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
 		};
 
-		gsbi@1a200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
+		l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l10 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
 
-			serial@1a240000 {
-				status = "okay";
+		l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
 
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi5_uart_pin_a>;
-			};
+		l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
 		};
 
-		amba {
-			sdcc1: mmc@12400000 {
-				status = "okay";
+		l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
 
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
+		l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
 
-			sdcc3: mmc@12180000 {
-				status = "okay";
+		l17 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
 
-				vmmc-supply = <&pm8921_l6>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+		l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
 
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
-			};
+		l21 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
 		};
 
-		riva-pil@3204000 {
-			status = "okay";
+		l22 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+		l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		l27 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		l28 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		l29 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		lvs1 {
+			bias-pull-down;
+		};
+
+		lvs2 {
+			bias-pull-down;
+		};
+
+		lvs3 {
+			bias-pull-down;
+		};
+
+		lvs4 {
+			bias-pull-down;
+		};
+
+		lvs5 {
+			bias-pull-down;
+		};
+
+		lvs6 {
+			bias-pull-down;
+		};
+
+		lvs7 {
+			bias-pull-down;
+		};
+
+		usb-switch {};
+
+		hdmi-switch {};
+
+		ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
 		};
 	};
 };
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
+
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	gsbi5_uart_pin_a: gsbi5-uart-pin-active {
+		rx {
+			pins = "gpio52";
+			function = "gsbi5";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		tx {
+			pins = "gpio51";
+			function = "gsbi5";
+			drive-strength = <4>;
+			bias-disable;
+		};
+	};
+
+
+	sdcc3_cd_pin_a: sdcc3-cd-pin-active {
+		pins = "gpio26";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 942aa2278355..0da9623ea084 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -672,7 +672,7 @@
 			reg = <0x00c00000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pm8821: pmic@1 {
+			pm8821: pmic {
 				compatible = "qcom,pm8821";
 				interrupt-parent = <&tlmm_pinmux>;
 				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
@@ -693,12 +693,12 @@
 			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic@0 {
+			pmicintc: pmic {
 				compatible = "qcom,pm8921";
 				interrupt-parent = <&tlmm_pinmux>;
 				interrupts = <74 8>;
@@ -884,7 +884,7 @@
 			reg = <0x2011000 0x1000>;
 		};
 
-		rpm@108000 {
+		rpm: rpm@108000 {
 			compatible = "qcom,rpm-apq8064";
 			reg = <0x108000 0x1000>;
 			qcom,ipc = <&l2cc 0x8 2>;
@@ -1085,15 +1085,21 @@
 			ports-implemented = <0x1>;
 		};
 
-		/* Temporary fixed regulator */
-		sdcc1bam: dma-controller@12402000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+			dma-names = "tx", "rx";
 		};
 
 		sdcc3bam: dma-controller@12182000{
@@ -1106,6 +1112,24 @@
 			qcom,ee = <0>;
 		};
 
+		sdcc4: mmc@121c0000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x121c0000 0x2000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdc4_gpios>;
+		};
+
 		sdcc4bam: dma-controller@121c2000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x121c2000 0x8000>;
@@ -1116,67 +1140,33 @@
 			qcom,ee = <0>;
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12400000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc1_pins>;
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12400000 0x2000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12180000 0x2000>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <192000000>;
-				no-1-8-v;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdcc1_pins>;
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+		};
 
-			sdcc4: mmc@121c0000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x121c0000 0x2000>;
-				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <48000000>;
-				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
-				dma-names = "tx", "rx";
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdc4_gpios>;
-			};
+		sdcc1bam: dma-controller@12402000{
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
 		};
 
 		tcsr: syscon@1a400000 {
@@ -1316,7 +1306,6 @@
 						<&dsi0_phy 1>;
 			syscon-sfpb = <&mmss_sfpb>;
 			phys = <&dsi0_phy>;
-			phy-names = "dsi";
 			status = "disabled";
 
 			ports {
@@ -1338,7 +1327,7 @@
 		};
 
 
-		dsi0_phy: dsi-phy@4700200 {
+		dsi0_phy: phy@4700200 {
 			compatible = "qcom,dsi-phy-28nm-8960";
 			#clock-cells = <1>;
 			#phy-cells = <0>;
@@ -1470,6 +1459,8 @@
 
 			phys = <&hdmi_phy>;
 
+			status = "disabled";
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1488,7 +1479,7 @@
 			};
 		};
 
-		hdmi_phy: hdmi-phy@4a00400 {
+		hdmi_phy: phy@4a00400 {
 			compatible = "qcom,hdmi-phy-8960";
 			reg = <0x4a00400 0x60>,
 			      <0x4a00500 0x100>;
@@ -1498,6 +1489,8 @@
 			clocks = <&mmcc HDMI_S_AHB_CLK>;
 			clock-names = "slave_iface";
 			#phy-cells = <0>;
+
+			status = "disabled";
 		};
 
 		mdp: mdp@5100000 {
@@ -1552,7 +1545,7 @@
 			};
 		};
 
-		riva: riva-pil@3204000 {
+		riva: riva-pil@3200800 {
 			compatible = "qcom,riva-pil";
 
 			reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
@@ -1615,7 +1608,7 @@
 		};
 
 		etb@1a01000 {
-			compatible = "coresight-etb10", "arm,primecell";
+			compatible = "arm,coresight-etb10", "arm,primecell";
 			reg = <0x1a01000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>;
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index 91716298ec5e..1345df7cbd00 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -35,30 +35,8 @@
 	};
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs2_phy>;
-	phy-select = <&tcsr 0xb000 1>;
-	extcon = <&smbb>, <&usb_id>;
-	vbus-supply = <&chg_otg>;
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@b {
-			status = "okay";
-			v3p3-supply = <&pm8941_l24>;
-			v1p8-supply = <&pm8941_l6>;
-			extcon = <&smbb>;
-			qcom,init-seq = /bits/ 8 <0x1 0x63>;
-		};
-	};
-};
-
 &rpm_requests {
-	pm8841-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pm8841-regulators";
 
 		pm8841_s1: s1 {
@@ -82,7 +60,7 @@
 		};
 	};
 
-	pm8941-regulators {
+	regulators-1 {
 		compatible = "qcom,rpm-pm8941-regulators";
 
 		vdd_l1_l3-supply = <&pm8941_s1>;
@@ -272,34 +250,34 @@
 };
 
 &tlmm {
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc2-on {
-		clk {
+	sdc2_on: sdc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <10>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 
-		cd {
+		cd-pins {
 			pins = "gpio62";
 			function = "gpio";
 			drive-strength = <2>;
@@ -307,3 +285,23 @@
 		};
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs2_phy>;
+	phy-select = <&tcsr 0xb000 1>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs2_phy {
+	status = "okay";
+	v3p3-supply = <&pm8941_l24>;
+	v1p8-supply = <&pm8941_l6>;
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x63>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index f2fb7c975af8..fe30abfff90a 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -72,7 +72,7 @@
 		};
 
 		L2: l2-cache {
-			compatible = "qcom,arch-cache";
+			compatible = "cache";
 			cache-level = <2>;
 			qcom,saw = <&saw_l2>;
 		};
@@ -258,12 +258,14 @@
 		};
 
 		tsens: thermal-sensor@fc4a8000 {
-			compatible = "qcom,msm8974-tsens";
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
 			reg = <0xfc4a9000 0x1000>, /* TM */
 			      <0xfc4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
 			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
 			#thermal-sensor-cells = <1>;
 		};
 		timer@f9020000 {
@@ -394,7 +396,7 @@
 			#hwlock-cells = <1>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
@@ -474,7 +476,7 @@
 				compatible = "qcom,rpm-apq8084";
 				qcom,smd-channels = "rpm_requests";
 
-				pma8084-regulators {
+				regulators-0 {
 					compatible = "qcom,rpm-pma8084-regulators";
 
 					pma8084_s1: s1 {};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
index cf7da1ab177c..1b27edce9d4f 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
@@ -9,7 +9,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "ap120c-ac:green:power";
 			function = LED_FUNCTION_POWER;
 			color = <LED_COLOR_ID_GREEN>;
@@ -17,14 +17,14 @@
 			default-state = "on";
 		};
 
-		wlan {
+		led-wlan {
 			label = "ap120c-ac:green:wlan";
 			function = LED_FUNCTION_WLAN;
 			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
 		};
 
-		support {
+		led-support {
 			label = "ap120c-ac:green:support";
 			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
index c4f89b712fd9..a707057c887d 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
@@ -7,7 +7,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status: status {
+		status: led-status {
 			label = "ap120c-ac:blue:status";
 			function = LED_FUNCTION_STATUS;
 			color = <LED_COLOR_ID_BLUE>;
@@ -15,7 +15,7 @@
 			default-state = "keep";
 		};
 
-		wlan2g {
+		led-wlan2g {
 			label = "ap120c-ac:green:wlan2g";
 			function = LED_FUNCTION_WLAN;
 			color = <LED_COLOR_ID_GREEN>;
@@ -23,7 +23,7 @@
 			linux,default-trigger = "phy0tpt";
 		};
 
-		wlan5g {
+		led-wlan5g {
 			label = "ap120c-ac:red:wlan5g";
 			function = LED_FUNCTION_WLAN;
 			color = <LED_COLOR_ID_RED>;
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
index af9a26fb5d4a..a5a6f3ebb274 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
@@ -6,7 +6,7 @@
 
 / {
 	model = "ALFA Network AP120C-AC";
-	compatible = "alfa-network,ap120c-ac";
+	compatible = "alfa-network,ap120c-ac", "qcom,ipq4018";
 
 	keys {
 		compatible = "gpio-keys";
diff --git a/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts b/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
index 394412619894..365fbac417fd 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
+++ b/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
@@ -7,7 +7,7 @@
 
 / {
 	model = "8devices Jalapeno";
-	compatible = "8dev,jalapeno";
+	compatible = "8dev,jalapeno", "qcom,ipq4018";
 };
 
 &tlmm {
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index b23591110bd2..acb08dcf9442 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -348,7 +348,7 @@
 		saw0: regulator@b089000 {
 			compatible = "qcom,saw2";
 			reg = <0x0b089000 0x1000>, <0x0b009000 0x1000>;
-                        regulator;
+			regulator;
 		};
 
 		saw1: regulator@b099000 {
diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
index 5a65cce2500c..f908889c4f95 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "MikroTik RB3011UiAS-RM";
-	compatible = "mikrotik,rb3011";
+	compatible = "mikrotik,rb3011", "qcom,ipq8064";
 
 	aliases {
 		serial0 = &gsbi7_serial;
@@ -264,8 +264,7 @@
 &nand {
 	status = "okay";
 
-	nandcs@0 {
-		compatible = "qcom,nandcs";
+	nand@0 {
 		reg = <0>;
 
 		nand-ecc-strength = <4>;
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 90c08b51680a..7e784b0995da 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -513,8 +513,8 @@
 
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-ipq8064", "syscon";
-			clocks = <&pxo_board>, <&cxo_board>;
-			clock-names = "pxo", "cxo";
+			clocks = <&pxo_board>, <&cxo_board>, <&lcc PLL4>;
+			clock-names = "pxo", "cxo", "pll4";
 			reg = <0x00900000 0x4000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -728,7 +728,6 @@
 				status = "disabled";
 				reg = <0x12180000 0x2000>;
 				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <8>;
@@ -748,7 +747,6 @@
 				arm,primecell-periphid = <0x00051180>;
 				reg = <0x12400000 0x2000>;
 				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <8>;
@@ -756,7 +754,6 @@
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				mmc-ddr-1_8v;
 				vmmc-supply = <&vsdcc_fixed>;
 				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
 				dma-names = "tx", "rx";
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
index 0827de5426c1..a8304769b509 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
+++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -1,46 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
  * Device Tree Source for mangOH Green Board with WP8548 Module
  *
  * Copyright (C) 2016 BayLibre, SAS.
  * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/input/input.h>
@@ -82,8 +45,8 @@
 	 * - 42: IOT0_GPIO1 and SD Card Detect
 	 */
 
-	gpioext1_pins: gpioext1_pins {
-		pins {
+	gpioext1_pins: gpioext1-state {
+		gpioext1-pins {
 			pins = "gpio2";
 			function = "gpio";
 			input-enable;
@@ -91,8 +54,8 @@
 		};
 	};
 
-	sdc_cd_pins: sdc_cd_pins {
-		pins {
+	sdc_cd_pins: sdc-cd-state {
+		sdc-cd-pins {
 			pins = "gpio42";
 			function = "gpio";
 			drive-strength = <2>;
@@ -153,7 +116,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			gpioext0: gpio@3e {
+			gpioext0: pinctrl@3e {
 				/* GPIO Expander 0 Mapping :
 				 * - 0: ARDUINO_RESET_Level shift
 				 * - 1: BattChrgr_PG_N
@@ -179,7 +142,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -191,7 +154,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			gpioext1: gpio@3f {
+			gpioext1: pinctrl@3f {
 				/* GPIO Expander 1 Mapping :
 				 * - 0: GPIOEXP_INT1
 				 * - 1: Battery detect
@@ -220,7 +183,7 @@
 				interrupt-parent = <&msmgpio>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -232,7 +195,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			gpioext2: gpio@70 {
+			gpioext2: pinctrl@70 {
 				/* GPIO Expander 2 Mapping :
 				 * - 0: USB_HUB_INTn
 				 * - 1: HUB_CONNECT
@@ -258,7 +221,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
index 49de1821ac3a..92c8003dac25 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
@@ -1,46 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
  * Device Tree Source for Sierra Wireless WP8548 Module
  *
  * Copyright (C) 2016 BayLibre, SAS.
  * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include "qcom-mdm9615.dtsi"
@@ -59,8 +22,8 @@
 	pinctrl-0 = <&reset_out_pins>;
 	pinctrl-names = "default";
 
-	gsbi3_pins: gsbi3_pins {
-		mux {
+	gsbi3_pins: gsbi3-state {
+		gsbi3-pins {
 			pins = "gpio8", "gpio9", "gpio10", "gpio11";
 			function = "gsbi3";
 			drive-strength = <8>;
@@ -68,8 +31,8 @@
 		};
 	};
 
-	gsbi4_pins: gsbi4_pins {
-		mux {
+	gsbi4_pins: gsbi4-state {
+		gsbi4-pins {
 			pins = "gpio12", "gpio13", "gpio14", "gpio15";
 			function = "gsbi4";
 			drive-strength = <8>;
@@ -77,15 +40,15 @@
 		};
 	};
 
-	gsbi5_i2c_pins: gsbi5_i2c_pins {
-		pin16 {
+	gsbi5_i2c_pins: gsbi5-i2c-state {
+		sda-pins {
 			pins = "gpio16";
 			function = "gsbi5_i2c";
 			drive-strength = <8>;
 			bias-disable;
 		};
 
-		pin17 {
+		scl-pins {
 			pins = "gpio17";
 			function = "gsbi5_i2c";
 			drive-strength = <2>;
@@ -93,8 +56,8 @@
 		};
 	};
 
-	gsbi5_uart_pins: gsbi5_uart_pins {
-		mux {
+	gsbi5_uart_pins: gsbi5-uart-state {
+		gsbi5-uart-pins {
 			pins = "gpio18", "gpio19";
 			function = "gsbi5_uart";
 			drive-strength = <8>;
@@ -102,8 +65,8 @@
 		};
 	};
 
-	reset_out_pins: reset_out_pins {
-		pins {
+	reset_out_pins: reset-out-state {
+		reset-out-pins {
 			pins = "gpio66";
 			function = "gpio";
 			drive-strength = <2>;
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
index b47c86412de2..b0fe1d95d88f 100644
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -1,46 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
  * Device Tree Source for Qualcomm MDM9615 SoC
  *
  * Copyright (C) 2016 BayLibre, SAS.
  * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -64,6 +27,7 @@
 
 		cpu0: cpu@0 {
 			compatible = "arm,cortex-a5";
+			reg = <0>;
 			device_type = "cpu";
 			next-level-cache = <&L2>;
 		};
@@ -206,7 +170,6 @@
 				#size-cells = <0>;
 				reg = <0x16280000 0x1000>;
 				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
-				spi-max-frequency = <24000000>;
 
 				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
 				clock-names = "core", "iface";
@@ -283,7 +246,7 @@
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic@0 {
+			pmicintc: pmic {
 				compatible = "qcom,pm8018", "qcom,pm8921";
 				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <2>;
@@ -351,51 +314,43 @@
 			qcom,ee = <0>;
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12180000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12180000 0x2000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <48000000>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC1_CLK>;
-				assigned-clock-rates = <400000>;
-			};
+		sdcc1: mmc@12180000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <48000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC1_CLK>;
+			assigned-clock-rates = <400000>;
+		};
 
-			sdcc2: mmc@12140000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12140000 0x2000>;
-				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <48000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC2_CLK>;
-				assigned-clock-rates = <400000>;
-			};
+		sdcc2: mmc@12140000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12140000 0x2000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC2_CLK>;
+			assigned-clock-rates = <400000>;
 		};
 
 		tcsr: syscon@1a400000 {
diff --git a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts b/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
index 290e1df631f0..6a082ad4418a 100644
--- a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
+++ b/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
@@ -8,6 +8,7 @@
 / {
 	model = "Samsung Galaxy S III Neo";
 	compatible = "samsung,s3ve3g", "qcom,msm8226";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart3;
diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index cf2d56929428..4cba25dad8d6 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/reset/qcom,gcc-msm8974.h>
@@ -298,6 +299,33 @@
 			#size-cells = <0>;
 		};
 
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8226-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <400000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		usb: usb@f9a55000 {
 			compatible = "qcom,ci-hdrc";
 			reg = <0xf9a55000 0x200>,
@@ -344,6 +372,14 @@
 			#power-domain-cells = <1>;
 		};
 
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8226";
+			reg = <0xfd8c0000 0x6000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		tlmm: pinctrl@fd510000 {
 			compatible = "qcom,msm8226-pinctrl";
 			reg = <0xfd510000 0x4000>;
@@ -354,49 +390,65 @@
 			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 
-			blsp1_i2c1_pins: blsp1-i2c1 {
+			blsp1_i2c1_pins: blsp1-i2c1-state {
 				pins = "gpio2", "gpio3";
 				function = "blsp_i2c1";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c2_pins: blsp1-i2c2 {
+			blsp1_i2c2_pins: blsp1-i2c2-state {
 				pins = "gpio6", "gpio7";
 				function = "blsp_i2c2";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c3_pins: blsp1-i2c3 {
+			blsp1_i2c3_pins: blsp1-i2c3-state {
 				pins = "gpio10", "gpio11";
 				function = "blsp_i2c3";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c4_pins: blsp1-i2c4 {
+			blsp1_i2c4_pins: blsp1-i2c4-state {
 				pins = "gpio14", "gpio15";
 				function = "blsp_i2c4";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c5_pins: blsp1-i2c5 {
+			blsp1_i2c5_pins: blsp1-i2c5-state {
 				pins = "gpio18", "gpio19";
 				function = "blsp_i2c5";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
+			cci_default: cci-default-state {
+				pins = "gpio29", "gpio30";
+				function = "cci_i2c0";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_sleep: cci-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			sdhc1_default_state: sdhc1-default-state {
-				clk {
+				clk-pins {
 					pins = "sdc1_clk";
 					drive-strength = <10>;
 					bias-disable;
 				};
 
-				cmd-data {
+				cmd-data-pins {
 					pins = "sdc1_cmd", "sdc1_data";
 					drive-strength = <10>;
 					bias-pull-up;
@@ -404,13 +456,13 @@
 			};
 
 			sdhc2_default_state: sdhc2-default-state {
-				clk {
+				clk-pins {
 					pins = "sdc2_clk";
 					drive-strength = <10>;
 					bias-disable;
 				};
 
-				cmd-data {
+				cmd-data-pins {
 					pins = "sdc2_cmd", "sdc2_data";
 					drive-strength = <10>;
 					bias-pull-up;
@@ -418,21 +470,21 @@
 			};
 
 			sdhc3_default_state: sdhc3-default-state {
-				clk {
+				clk-pins {
 					pins = "gpio44";
 					function = "sdc3";
 					drive-strength = <8>;
 					bias-disable;
 				};
 
-				cmd {
+				cmd-pins {
 					pins = "gpio43";
 					function = "sdc3";
 					drive-strength = <8>;
 					bias-pull-up;
 				};
 
-				data {
+				data-pins {
 					pins = "gpio39", "gpio40", "gpio41", "gpio42";
 					function = "sdc3";
 					drive-strength = <8>;
@@ -527,7 +579,7 @@
 			};
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index ddce7d64ba99..86f76d0feff4 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -316,7 +316,7 @@
 			};
 		};
 
-		external-bus@1a100000 {
+		ebi2: external-bus@1a100000 {
 			compatible = "qcom,msm8660-ebi2";
 			#address-cells = <2>;
 			#size-cells = <1>;
@@ -333,12 +333,12 @@
 			status = "disabled";
 		};
 
-		qcom,ssbi@500000 {
+		ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pm8058: pmic@0 {
+			pm8058: pmic {
 				compatible = "qcom,pm8058";
 				interrupt-parent = <&tlmm>;
 				interrupts = <88 8>;
@@ -379,7 +379,7 @@
 					pull-up;
 				};
 
-				keypad@148 {
+				pm8058_keypad: keypad@148 {
 					compatible = "qcom,pm8058-keypad";
 					reg = <0x148>;
 					interrupt-parent = <&pm8058>;
@@ -444,6 +444,31 @@
 					compatible = "qcom,pm8058-vib";
 					reg = <0x4a>;
 				};
+
+				pm8058_led48: led@48 {
+					compatible = "qcom,pm8058-keypad-led";
+					reg = <0x48>;
+					status = "disabled";
+				};
+
+				pm8058_led131: led@131 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x131>;
+					status = "disabled";
+				};
+
+				pm8058_led132: led@132 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x132>;
+					status = "disabled";
+				};
+
+				pm8058_led133: led@133 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x133>;
+					status = "disabled";
+				};
+
 			};
 		};
 
@@ -471,7 +496,7 @@
 				clock-names = "pxo";
 			};
 
-			pm8901-regulators {
+			regulators-0 {
 				compatible = "qcom,rpm-pm8901-regulators";
 
 				pm8901_l0: l0 {};
@@ -495,7 +520,7 @@
 				pm8901_mvs: mvs {};
 			};
 
-			pm8058-regulators {
+			regulators-1 {
 				compatible = "qcom,rpm-pm8058-regulators";
 
 				pm8058_l0: l0 {};
@@ -549,7 +574,6 @@
 				arm,primecell-periphid = <0x00051180>;
 				reg = <0x12400000 0x8000>;
 				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <8>;
@@ -565,7 +589,6 @@
 				arm,primecell-periphid = <0x00051180>;
 				reg = <0x12140000 0x8000>;
 				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <8>;
@@ -580,7 +603,6 @@
 				status = "disabled";
 				reg = <0x12180000 0x8000>;
 				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <4>;
@@ -596,7 +618,6 @@
 				status = "disabled";
 				reg = <0x121c0000 0x8000>;
 				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <4>;
@@ -611,7 +632,6 @@
 				status = "disabled";
 				reg = <0x12200000 0x8000>;
 				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <4>;
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
index 9157e3c4f48f..8fa2befa629a 100644
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
@@ -18,7 +18,7 @@
 	regulators {
 		compatible = "simple-bus";
 
-		ext_l2: gpio-regulator@91 {
+		ext_l2: gpio-regulator {
 			compatible = "regulator-fixed";
 			regulator-name = "ext_l2";
 			gpio = <&msmgpio 91 0>;
@@ -42,7 +42,7 @@
 		compatible = "micrel,ks8851";
 		reg = <0>;
 		interrupt-parent = <&msmgpio>;
-		interrupts = <90 8>;
+		interrupts = <90 IRQ_TYPE_LEVEL_LOW>;
 		spi-max-frequency = <5400000>;
 		vdd-supply = <&ext_l2>;
 		vdd-io-supply = <&pm8921_lvs6>;
@@ -60,33 +60,32 @@
 };
 
 &msmgpio {
-	spi1_default: spi1_default {
-		 mux {
-			pins = "gpio6", "gpio7", "gpio9";
-			function = "gsbi1";
-		 };
-
-		 mosi {
+	spi1_default: spi1-default-state {
+		 mosi-pins {
 			pins = "gpio6";
+			function = "gsbi1";
 			drive-strength = <12>;
 			bias-disable;
 		 };
 
-		 miso {
+		 miso-pins {
 			pins = "gpio7";
+			function = "gsbi1";
 			drive-strength = <12>;
 			bias-disable;
 		 };
 
-		 cs {
+		 cs-pins {
 			pins = "gpio8";
+			function = "gsbi1";
 			drive-strength = <12>;
 			bias-disable;
 			output-low;
 		 };
 
-		 clk {
+		 clk-pins {
 			pins = "gpio9";
+			function = "gsbi1";
 			drive-strength = <12>;
 			bias-disable;
 		 };
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index c5740da3754c..7debf9db7cb1 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -17,7 +17,7 @@
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		interrupts = <1 14 0x304>;
+		interrupts = <GIC_PPI 14 0x304>;
 
 		cpu@0 {
 			compatible = "qcom,krait";
@@ -52,7 +52,7 @@
 
 	cpu-pmu {
 		compatible = "qcom,krait-pmu";
-		interrupts = <1 10 0x304>;
+		interrupts = <GIC_PPI 10 0x304>;
 		qcom,no-pc-write;
 	};
 
@@ -105,9 +105,9 @@
 		timer@200a000 {
 			compatible = "qcom,kpss-timer",
 				     "qcom,kpss-wdt-msm8960", "qcom,msm-timer";
-			interrupts = <1 1 0x301>,
-				     <1 2 0x301>,
-				     <1 3 0x301>;
+			interrupts = <GIC_PPI 1 0x301>,
+				     <GIC_PPI 2 0x301>,
+				     <GIC_PPI 3 0x301>;
 			reg = <0x0200a000 0x100>;
 			clock-frequency = <27000000>,
 					  <32768>;
@@ -119,7 +119,7 @@
 			gpio-controller;
 			gpio-ranges = <&msmgpio 0 0 152>;
 			#gpio-cells = <2>;
-			interrupts = <0 16 0x4>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			reg = <0x800000 0x4000>;
@@ -247,15 +247,15 @@
 			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic@0 {
+			pmicintc: pmic {
 				compatible = "qcom,pm8921";
 				interrupt-parent = <&msmgpio>;
-				interrupts = <104 8>;
+				interrupts = <104 IRQ_TYPE_LEVEL_LOW>;
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				#address-cells = <1>;
@@ -265,7 +265,8 @@
 					compatible = "qcom,pm8921-pwrkey";
 					reg = <0x1c>;
 					interrupt-parent = <&pmicintc>;
-					interrupts = <50 1>, <51 1>;
+					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+						     <51 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15625>;
 					pull-up;
 				};
@@ -274,7 +275,8 @@
 					compatible = "qcom,pm8921-keypad";
 					reg = <0x148>;
 					interrupt-parent = <&pmicintc>;
-					interrupts = <74 1>, <75 1>;
+					interrupts = <74 IRQ_TYPE_EDGE_RISING>,
+						     <75 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15>;
 					scan-delay = <32>;
 					row-hold = <91500>;
@@ -283,7 +285,7 @@
 				rtc@11d {
 					compatible = "qcom,pm8921-rtc";
 					interrupt-parent = <&pmicintc>;
-					interrupts = <39 1>;
+					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
 					reg = <0x11d>;
 					allow-set-time;
 				};
@@ -297,44 +299,36 @@
 			clock-names = "core";
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12400000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12400000 0x8000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x8000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+		};
 
-			sdcc3: mmc@12180000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12180000 0x8000>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <192000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x8000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
 		};
 
 		tcsr: syscon@1a400000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 6daceaa87802..280e63e3ebf2 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -9,6 +9,7 @@
 / {
 	model = "LGE MSM 8974 HAMMERHEAD";
 	compatible = "lge,hammerhead", "qcom,msm8974";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart1;
@@ -247,31 +248,6 @@
 	status = "okay";
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs1_phy>;
-	phy-select = <&tcsr 0xb000 0>;
-
-	extcon = <&charger>, <&usb_id>;
-	vbus-supply = <&usb_otg_vbus>;
-
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@a {
-			status = "okay";
-
-			v1p8-supply = <&pm8941_l6>;
-			v3p3-supply = <&pm8941_l24>;
-
-			qcom,init-seq = /bits/ 8 <0x1 0x64>;
-		};
-	};
-};
-
 &pm8941_gpios {
 	gpio_keys_pin_a: gpio-keys-active-state {
 		pins = "gpio2", "gpio3";
@@ -344,7 +320,7 @@
 };
 
 &rpm_requests {
-	pm8841-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pm8841-regulators";
 
 		pm8841_s1: s1 {
@@ -368,7 +344,7 @@
 		};
 	};
 
-	pm8941-regulators {
+	regulators-1 {
 		compatible = "qcom,rpm-pm8941-regulators";
 
 		vdd_l1_l3-supply = <&pm8941_s1>;
@@ -573,43 +549,43 @@
 };
 
 &tlmm {
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc2-on {
-		clk {
+	sdc2_on: sdc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <6>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 	};
 
-	mpu6515_pin: mpu6515 {
+	mpu6515_pin: mpu6515-state {
 		pins = "gpio73";
 		function = "gpio";
 		bias-disable;
 		input-enable;
 	};
 
-	touch_pin: touch {
-		int {
+	touch_pin: touch-state {
+		int-pins {
 			pins = "gpio5";
 			function = "gpio";
 
@@ -618,7 +594,7 @@
 			input-enable;
 		};
 
-		reset {
+		reset-pins {
 			pins = "gpio8";
 			function = "gpio";
 
@@ -627,27 +603,50 @@
 		};
 	};
 
-	panel_pin: panel {
+	panel_pin: panel-state {
 		pins = "gpio12";
 		function = "mdp_vsync";
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	bt_pin: bt {
-		hostwake {
+	bt_pin: bt-state {
+		hostwake-pins {
 			pins = "gpio42";
 			function = "gpio";
 		};
 
-		devwake {
+		devwake-pins {
 			pins = "gpio62";
 			function = "gpio";
 		};
 
-		shutdown {
+		shutdown-pins {
 			pins = "gpio41";
 			function = "gpio";
 		};
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	extcon = <&charger>, <&usb_id>;
+	vbus-supply = <&usb_otg_vbus>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
index 68d5626bf491..9f2ab5c122d0 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -4,6 +4,7 @@
 / {
 	model = "Sony Xperia Z1 Compact";
 	compatible = "sony,xperia-amami", "qcom,msm8974";
+	chassis-type = "handset";
 };
 
 &smbb {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
index ea6a941d8f8c..9028f17e5c4a 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -4,4 +4,5 @@
 / {
 	model = "Sony Xperia Z1";
 	compatible = "sony,xperia-honami", "qcom,msm8974";
+	chassis-type = "handset";
 };
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi
index 5a70683d9103..1b683690a1ad 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -132,31 +132,6 @@
 	/* sii8334 MHL HDMI bridge */
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs1_phy>;
-	phy-select = <&tcsr 0xb000 0>;
-	extcon = <&smbb>, <&usb_id>;
-	vbus-supply = <&chg_otg>;
-
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@a {
-			status = "okay";
-
-			v1p8-supply = <&pm8941_l6>;
-			v3p3-supply = <&pm8941_l24>;
-
-			extcon = <&smbb>;
-			qcom,init-seq = /bits/ 8 <0x1 0x64>;
-		};
-	};
-};
-
 &pm8941_coincell {
 	status = "okay";
 	qcom,rset-ohms = <2100>;
@@ -178,7 +153,7 @@
 
 	qcom,power-source = <1>;
 
-	rgb-led {
+	multi-led {
 		color = <LED_COLOR_ID_RGB>;
 		function = LED_FUNCTION_STATUS;
 
@@ -214,7 +189,7 @@
 };
 
 &rpm_requests {
-	pm8841-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pm8841-regulators";
 
 		pm8841_s1: s1 {
@@ -238,7 +213,7 @@
 		};
 	};
 
-	pm8941-regulators {
+	regulators-1 {
 		compatible = "qcom,rpm-pm8941-regulators";
 
 		vdd_l1_l3-supply = <&pm8941_s1>;
@@ -442,7 +417,7 @@
 };
 
 &tlmm {
-	ts_int_pin: touch-int {
+	ts_int_pin: touch-int-state {
 		pins = "gpio61";
 		function = "gpio";
 		drive-strength = <2>;
@@ -450,34 +425,34 @@
 		input-enable;
 	};
 
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc-on {
-		clk {
+	sdc2_on: sdc-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <10>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 
-		cd {
+		cd-pins {
 			pins = "gpio62";
 			function = "gpio";
 			drive-strength = <2>;
@@ -485,3 +460,26 @@
 		};
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 7a9be0acf3f5..8d216a3c0851 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -653,7 +653,7 @@
 			#size-cells = <0>;
 		};
 
-		otg: usb@f9a55000 {
+		usb: usb@f9a55000 {
 			compatible = "qcom,ci-hdrc";
 			reg = <0xf9a55000 0x200>,
 			      <0xf9a55200 0x200>;
@@ -679,7 +679,7 @@
 					#phy-cells = <0>;
 					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
 					clock-names = "ref", "sleep";
-					resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
 					reset-names = "phy", "por";
 					status = "disabled";
 				};
@@ -690,7 +690,7 @@
 					#phy-cells = <0>;
 					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
 					clock-names = "ref", "sleep";
-					resets = <&gcc GCC_USB2B_PHY_BCR>, <&otg 1>;
+					resets = <&gcc GCC_USB2B_PHY_BCR>, <&usb 1>;
 					reset-names = "phy", "por";
 					status = "disabled";
 				};
@@ -1056,7 +1056,7 @@
 			reg = <0xfc400000 0x4000>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
@@ -1116,7 +1116,7 @@
 		};
 
 		tsens: thermal-sensor@fc4a9000 {
-			compatible = "qcom,msm8974-tsens";
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
 			reg = <0xfc4a9000 0x1000>, /* TM */
 			      <0xfc4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
@@ -1194,7 +1194,7 @@
 			resets = <&gcc GCC_MSS_RESTART>;
 			reset-names = "mss_restart";
 
-			qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
+			qcom,halt-regs = <&tcsr_mutex 0x1180 0x1200 0x1280>;
 
 			qcom,smem-states = <&modem_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
@@ -1233,13 +1233,14 @@
 			};
 		};
 
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8974-tcsr-mutex", "qcom,tcsr-mutex", "syscon";
 			reg = <0xfd484000 0x2000>;
+			#hwlock-cells = <1>;
 		};
 
 		tcsr: syscon@fd4a0000 {
-			compatible = "syscon";
+			compatible = "qcom,tcsr-msm8974", "syscon";
 			reg = <0xfd4a0000 0x10000>;
 		};
 
@@ -1253,61 +1254,62 @@
 			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 
-			sdc1_off: sdc1-off {
-				clk {
+			sdc1_off: sdc1-off-state {
+				clk-pins {
 					pins = "sdc1_clk";
 					bias-disable;
 					drive-strength = <2>;
 				};
 
-				cmd {
+				cmd-pins {
 					pins = "sdc1_cmd";
 					bias-pull-up;
 					drive-strength = <2>;
 				};
 
-				data {
+				data-pins {
 					pins = "sdc1_data";
 					bias-pull-up;
 					drive-strength = <2>;
 				};
 			};
 
-			sdc2_off: sdc2-off {
-				clk {
+			sdc2_off: sdc2-off-state {
+				clk-pins {
 					pins = "sdc2_clk";
 					bias-disable;
 					drive-strength = <2>;
 				};
 
-				cmd {
+				cmd-pins {
 					pins = "sdc2_cmd";
 					bias-pull-up;
 					drive-strength = <2>;
 				};
 
-				data {
+				data-pins {
 					pins = "sdc2_data";
 					bias-pull-up;
 					drive-strength = <2>;
 				};
 
-				cd {
+				cd-pins {
 					pins = "gpio54";
+					function = "gpio";
 					bias-disable;
 					drive-strength = <2>;
 				};
 			};
 
-			blsp1_uart2_default: blsp1-uart2-default {
-				rx {
+			blsp1_uart2_default: blsp1-uart2-default-state {
+				rx-pins {
 					pins = "gpio5";
 					function = "blsp_uart2";
 					drive-strength = <2>;
 					bias-pull-up;
 				};
 
-				tx {
+				tx-pins {
 					pins = "gpio4";
 					function = "blsp_uart2";
 					drive-strength = <4>;
@@ -1315,15 +1317,15 @@
 				};
 			};
 
-			blsp2_uart1_default: blsp2-uart1-default {
-				tx-rts {
+			blsp2_uart1_default: blsp2-uart1-default-state {
+				tx-rts-pins {
 					pins = "gpio41", "gpio44";
 					function = "blsp_uart7";
 					drive-strength = <2>;
 					bias-disable;
 				};
 
-				rx-cts {
+				rx-cts-pins {
 					pins = "gpio42", "gpio43";
 					function = "blsp_uart7";
 					drive-strength = <2>;
@@ -1331,22 +1333,22 @@
 				};
 			};
 
-			blsp2_uart1_sleep: blsp2-uart1-sleep {
+			blsp2_uart1_sleep: blsp2-uart1-sleep-state {
 				pins = "gpio41", "gpio42", "gpio43", "gpio44";
 				function = "gpio";
 				drive-strength = <2>;
 				bias-pull-down;
 			};
 
-			blsp2_uart4_default: blsp2-uart4-default {
-				tx-rts {
+			blsp2_uart4_default: blsp2-uart4-default-state {
+				tx-rts-pins {
 					pins = "gpio53", "gpio56";
 					function = "blsp_uart10";
 					drive-strength = <2>;
 					bias-disable;
 				};
 
-				rx-cts {
+				rx-cts-pins {
 					pins = "gpio54", "gpio55";
 					function = "blsp_uart10";
 					drive-strength = <2>;
@@ -1354,42 +1356,42 @@
 				};
 			};
 
-			blsp1_i2c1_default: blsp1-i2c1-default {
+			blsp1_i2c1_default: blsp1-i2c1-default-state {
 				pins = "gpio2", "gpio3";
 				function = "blsp_i2c1";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c1_sleep: blsp1-i2c1-sleep {
+			blsp1_i2c1_sleep: blsp1-i2c1-sleep-state {
 				pins = "gpio2", "gpio3";
 				function = "blsp_i2c1";
 				drive-strength = <2>;
 				bias-pull-up;
 			};
 
-			blsp1_i2c2_default: blsp1-i2c2-default {
+			blsp1_i2c2_default: blsp1-i2c2-default-state {
 				pins = "gpio6", "gpio7";
 				function = "blsp_i2c2";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c2_sleep: blsp1-i2c2-sleep {
+			blsp1_i2c2_sleep: blsp1-i2c2-sleep-state {
 				pins = "gpio6", "gpio7";
 				function = "blsp_i2c2";
 				drive-strength = <2>;
 				bias-pull-up;
 			};
 
-			blsp1_i2c3_default: blsp1-i2c3-default {
+			blsp1_i2c3_default: blsp1-i2c3-default-state {
 				pins = "gpio10", "gpio11";
 				function = "blsp_i2c3";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c3_sleep: blsp1-i2c3-sleep {
+			blsp1_i2c3_sleep: blsp1-i2c3-sleep-state {
 				pins = "gpio10", "gpio11";
 				function = "blsp_i2c3";
 				drive-strength = <2>;
@@ -1400,14 +1402,14 @@
 
 			/* BLSP1_I2C5 info is missing */
 
-			blsp1_i2c6_default: blsp1-i2c6-default {
+			blsp1_i2c6_default: blsp1-i2c6-default-state {
 				pins = "gpio29", "gpio30";
 				function = "blsp_i2c6";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c6_sleep: blsp1-i2c6-sleep {
+			blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
 				pins = "gpio29", "gpio30";
 				function = "blsp_i2c6";
 				drive-strength = <2>;
@@ -1417,14 +1419,14 @@
 
 			/* BLSP2_I2C1 info is missing */
 
-			blsp2_i2c2_default: blsp2-i2c2-default {
+			blsp2_i2c2_default: blsp2-i2c2-default-state {
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c8";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp2_i2c2_sleep: blsp2-i2c2-sleep {
+			blsp2_i2c2_sleep: blsp2-i2c2-sleep-state {
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c8";
 				drive-strength = <2>;
@@ -1435,48 +1437,80 @@
 
 			/* BLSP2_I2C4 info is missing */
 
-			blsp2_i2c5_default: blsp2-i2c5-default {
+			blsp2_i2c5_default: blsp2-i2c5-default-state {
 				pins = "gpio83", "gpio84";
 				function = "blsp_i2c11";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp2_i2c5_sleep: blsp2-i2c5-sleep {
+			blsp2_i2c5_sleep: blsp2-i2c5-sleep-state {
 				pins = "gpio83", "gpio84";
 				function = "blsp_i2c11";
 				drive-strength = <2>;
 				bias-pull-up;
 			};
 
-			blsp2_i2c6_default: blsp2-i2c6-default {
+			blsp2_i2c6_default: blsp2-i2c6-default-state {
 				pins = "gpio87", "gpio88";
 				function = "blsp_i2c12";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp2_i2c6_sleep: blsp2-i2c6-sleep {
+			blsp2_i2c6_sleep: blsp2-i2c6-sleep-state {
 				pins = "gpio87", "gpio88";
 				function = "blsp_i2c12";
 				drive-strength = <2>;
 				bias-pull-up;
 			};
 
-			spi8_default: spi8_default {
-				mosi {
+			cci_default: cci-default-state {
+				cci_i2c0_default: cci-i2c0-default-pins {
+					pins = "gpio19", "gpio20";
+					function = "cci_i2c0";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_default: cci-i2c1-default-pins {
+					pins = "gpio21", "gpio22";
+					function = "cci_i2c1";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			cci_sleep: cci-sleep-state {
+				cci_i2c0_sleep: cci-i2c0-sleep-pins {
+					pins = "gpio19", "gpio20";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_sleep: cci-i2c1-sleep-pins {
+					pins = "gpio21", "gpio22";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			spi8_default: spi8_default-state {
+				mosi-pins {
 					pins = "gpio45";
 					function = "blsp_spi8";
 				};
-				miso {
+				miso-pins {
 					pins = "gpio46";
 					function = "blsp_spi8";
 				};
-				cs {
+				cs-pins {
 					pins = "gpio47";
 					function = "blsp_spi8";
 				};
-				clk {
+				clk-pins {
 					pins = "gpio48";
 					function = "blsp_spi8";
 				};
@@ -1571,7 +1605,6 @@
 					      "core_mmss";
 
 				phys = <&dsi0_phy>;
-				phy-names = "dsi-phy";
 
 				status = "disabled";
 
@@ -1597,7 +1630,7 @@
 				};
 			};
 
-			dsi0_phy: dsi-phy@fd922a00 {
+			dsi0_phy: phy@fd922a00 {
 				compatible = "qcom,dsi-phy-28nm-hpm";
 				reg = <0xfd922a00 0xd4>,
 				      <0xfd922b00 0x280>,
@@ -1616,6 +1649,40 @@
 			};
 		};
 
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8974-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		gpu: adreno@fdb00000 {
 			compatible = "qcom,adreno-330.1", "qcom,adreno";
 			reg = <0xfdb00000 0x10000>;
@@ -1703,8 +1770,6 @@
 				qcom,ipc = <&apcs 8 8>;
 				qcom,smd-edge = <1>;
 				label = "lpass";
-				#address-cells = <1>;
-				#size-cells = <0>;
 			};
 		};
 
@@ -1719,13 +1784,6 @@
 		};
 	};
 
-	tcsr_mutex: tcsr-mutex {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_block 0 0x80>;
-
-		#hwlock-cells = <1>;
-	};
-
 	thermal-zones {
 		cpu0-thermal {
 			polling-delay-passive = <250>;
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
index ff6e0066768b..f531d2679f6c 100644
--- a/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
@@ -8,7 +8,8 @@
 
 / {
 	model = "Fairphone 2";
-	compatible = "fairphone,fp2", "qcom,msm8974";
+	compatible = "fairphone,fp2", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
 
 	aliases {
 		mmc0 = &sdhc_1;
@@ -85,31 +86,6 @@
 	};
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs1_phy>;
-	phy-select = <&tcsr 0xb000 0>;
-	extcon = <&smbb>, <&usb_id>;
-	vbus-supply = <&chg_otg>;
-
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@a {
-			status = "okay";
-
-			v1p8-supply = <&pm8941_l6>;
-			v3p3-supply = <&pm8941_l24>;
-
-			extcon = <&smbb>;
-			qcom,init-seq = /bits/ 8 <0x1 0x64>;
-		};
-	};
-};
-
 &pm8941_gpios {
 	gpio_keys_pin_a: gpio-keys-active-state {
 		pins = "gpio1", "gpio2", "gpio5";
@@ -190,7 +166,7 @@
 };
 
 &rpm_requests {
-	pm8841-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pm8841-regulators";
 
 		pm8841_s1: s1 {
@@ -209,7 +185,7 @@
 		};
 	};
 
-	pm8941-regulators {
+	regulators-1 {
 		compatible = "qcom,rpm-pm8941-regulators";
 
 		vdd_l1_l3-supply = <&pm8941_s1>;
@@ -408,36 +384,36 @@
 };
 
 &tlmm {
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc2-on {
-		clk {
+	sdc2_on: sdc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <10>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 	};
 
-	wcnss_pin_a: wcnss-pin-active {
-		wlan {
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
 			pins =  "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
 			function = "wlan";
 
@@ -445,7 +421,7 @@
 			bias-pull-down;
 		};
 
-		bt {
+		bt-pins {
 			pins = "gpio35", "gpio43", "gpio44";
 			function = "bt";
 
@@ -453,7 +429,7 @@
 			bias-pull-down;
 		};
 
-		fm {
+		fm-pins {
 			pins = "gpio41", "gpio42";
 			function = "fm";
 
@@ -462,3 +438,26 @@
 		};
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts
new file mode 100644
index 000000000000..b5606623f968
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts
@@ -0,0 +1,417 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "OnePlus One";
+	compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+	qcom,msm-id = <194 0x10000>;
+	qcom,board-id = <8 0>;
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+		power-supplies = <&bq24196_charger>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	rmi4-i2c-dev@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		syna,startup-delay-ms = <100>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+			/*
+			 * Touchscreen size is 2040x1080, y-values between
+			 * 1920-2040 are used for touchkey (menu, home & back).
+			 * For now clip it off so we don't get touch events
+			 * outside of the display area.
+			 */
+			syna,clip-y-high = <1920>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	bq24196_charger: charger@6b {
+		compatible = "ti,bq24196";
+		reg = <0x6b>;
+		interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+		omit-battery-class;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&gcc {
+	compatible = "qcom,gcc-msm8974pro-ac";
+};
+
+&pm8941_coincell {
+	qcom,rset-ohms = <800>;
+	qcom,vset-millivolts = <3200>;
+
+	status = "okay";
+};
+
+&pronto {
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <875000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+
+	status = "okay";
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	touch_default_state: touch-default-state {
+		int-pins {
+			pins = "gpio61";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+			input-enable;
+		};
+
+		reset-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
+			pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt-pins {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&usb {
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
index 983e10c3d863..b9698ffb66ca 100644
--- a/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
@@ -7,7 +7,8 @@
 
 / {
 	model = "Samsung Galaxy S5";
-	compatible = "samsung,klte", "qcom,msm8974";
+	compatible = "samsung,klte", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart1;
@@ -375,28 +376,6 @@
 	status = "okay";
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs1_phy>;
-	phy-select = <&tcsr 0xb000 0>;
-
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@a {
-			status = "okay";
-
-			v1p8-supply = <&pma8084_l6>;
-			v3p3-supply = <&pma8084_l24>;
-
-			qcom,init-seq = /bits/ 8 <0x1 0x64>;
-		};
-	};
-};
-
 &pma8084_gpios {
 	gpio_keys_pin_a: gpio-keys-active-state {
 		pins = "gpio2", "gpio3", "gpio5";
@@ -470,7 +449,7 @@
 };
 
 &rpm_requests {
-	pma8084-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pma8084-regulators";
 
 		pma8084_s1: s1 {
@@ -706,57 +685,57 @@
 
 &tlmm {
 	/* This seems suspicious, but somebody with this device should look into it. */
-	blsp2_uart2_pins_active: blsp2-uart2-pins-active {
+	blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
 		pins = "gpio45", "gpio46", "gpio47", "gpio48";
 		function = "blsp_uart8";
 		drive-strength = <8>;
 		bias-disable;
 	};
 
-	blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep {
+	blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
 		pins = "gpio45", "gpio46", "gpio47", "gpio48";
 		function = "gpio";
 		drive-strength = <2>;
 		bias-pull-down;
 	};
 
-	bt_pins: bt-pins {
-		hostwake {
+	bt_pins: bt-pins-state {
+		hostwake-pins {
 			pins = "gpio75";
 			function = "gpio";
 			drive-strength = <16>;
 			input-enable;
 		};
 
-		devwake {
+		devwake-pins {
 			pins = "gpio91";
 			function = "gpio";
 			drive-strength = <2>;
 		};
 	};
 
-	sdc1_on: sdhc1-on {
-		clk {
+	sdc1_on: sdhc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <4>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <4>;
 			bias-pull-up;
 		};
 	};
 
-	sdc3_on: sdc3-on {
+	sdc3_on: sdc3-on-state {
 		pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
 		function = "sdc3";
 		drive-strength = <8>;
 		bias-disable;
 	};
 
-	sdhc3_cd_pin: sdc3-cd-on {
+	sdhc3_cd_pin: sdc3-cd-on-state {
 		pins = "gpio62";
 		function = "gpio";
 
@@ -764,52 +743,72 @@
 		bias-disable;
 	};
 
-	sdc2_on: sdhc2-on {
-		clk {
+	sdc2_on: sdhc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <6>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 	};
 
-	i2c_touchkey_pins: i2c-touchkey {
+	i2c_touchkey_pins: i2c-touchkey-state {
 		pins = "gpio95", "gpio96";
 		function = "gpio";
 		input-enable;
 		bias-pull-up;
 	};
 
-	i2c_led_gpioex_pins: i2c-led-gpioex {
+	i2c_led_gpioex_pins: i2c-led-gpioex-state {
 		pins = "gpio120", "gpio121";
 		function = "gpio";
 		input-enable;
 		bias-pull-down;
 	};
 
-	gpioex_pin: gpioex {
+	gpioex_pin: gpioex-state {
 		pins = "gpio145";
 		function = "gpio";
 		bias-pull-up;
 		drive-strength = <2>;
 	};
 
-	wifi_pin: wifi {
+	wifi_pin: wifi-state {
 		pins = "gpio92";
 		function = "gpio";
 		input-enable;
 		bias-pull-down;
 	};
 
-	panel_te_pin: panel {
+	panel_te_pin: panel-state {
 		pins = "gpio12";
 		function = "mdp_vsync";
 		drive-strength = <2>;
 		bias-disable;
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pma8084_l6>;
+	v3p3-supply = <&pma8084_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts
index 3f45f5c5d37b..3b1cc39f2269 100644
--- a/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts
+++ b/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -8,7 +8,8 @@
 
 / {
 	model = "Sony Xperia Z2 Tablet";
-	compatible = "sony,xperia-castor", "qcom,msm8974";
+	compatible = "sony,xperia-castor", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "tablet";
 
 	aliases {
 		serial0 = &blsp1_uart2;
@@ -212,31 +213,6 @@
 	};
 };
 
-&otg {
-	status = "okay";
-
-	phys = <&usb_hs1_phy>;
-	phy-select = <&tcsr 0xb000 0>;
-	extcon = <&smbb>, <&usb_id>;
-	vbus-supply = <&chg_otg>;
-
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-
-	ulpi {
-		phy@a {
-			status = "okay";
-
-			v1p8-supply = <&pm8941_l6>;
-			v3p3-supply = <&pm8941_l24>;
-
-			extcon = <&smbb>;
-			qcom,init-seq = /bits/ 8 <0x1 0x64>;
-		};
-	};
-};
-
 &pm8941_coincell {
 	status = "okay";
 
@@ -294,7 +270,7 @@
 
 	qcom,power-source = <1>;
 
-	rgb-led {
+	multi-led {
 		color = <LED_COLOR_ID_RGB>;
 		function = LED_FUNCTION_STATUS;
 
@@ -319,7 +295,7 @@
 };
 
 &rpm_requests {
-	pm8941-regulators {
+	regulators-0 {
 		compatible = "qcom,rpm-pm8941-regulators";
 
 		vdd_l1_l3-supply = <&pm8941_s1>;
@@ -548,41 +524,42 @@
 };
 
 &tlmm {
-	lcd_backlight_en_pin_a: lcd-backlight-vddio {
+	lcd_backlight_en_pin_a: lcd-backlight-vddio-state {
 		pins = "gpio69";
+		function = "gpio";
 		drive-strength = <10>;
 		output-low;
 		bias-disable;
 	};
 
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc2-on {
-		clk {
+	sdc2_on: sdc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <6>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 
-		cd {
+		cd-pins {
 			pins = "gpio62";
 			function = "gpio";
 			drive-strength = <2>;
@@ -590,22 +567,22 @@
 		};
 	};
 
-	sdc3_on: sdc3-on {
-		clk {
+	sdc3_on: sdc3-on-state {
+		clk-pins {
 			pins = "gpio40";
 			function = "sdc3";
 			drive-strength = <10>;
 			bias-disable;
 		};
 
-		cmd {
+		cmd-pins {
 			pins = "gpio39";
 			function = "sdc3";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 
-		data {
+		data-pins {
 			pins = "gpio35", "gpio36", "gpio37", "gpio38";
 			function = "sdc3";
 			drive-strength = <10>;
@@ -613,7 +590,7 @@
 		};
 	};
 
-	ts_int_pin: ts-int-pin {
+	ts_int_pin: ts-int-pin-state {
 		pins = "gpio86";
 		function = "gpio";
 		drive-strength = <2>;
@@ -621,7 +598,7 @@
 		input-enable;
 	};
 
-	bt_host_wake_pin: bt-host-wake {
+	bt_host_wake_pin: bt-host-wake-state {
 		pins = "gpio95";
 		function = "gpio";
 		drive-strength = <2>;
@@ -629,10 +606,33 @@
 		output-low;
 	};
 
-	bt_dev_wake_pin: bt-dev-wake {
+	bt_dev_wake_pin: bt-dev-wake-state {
 		pins = "gpio96";
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
 	};
 };
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom-pm8226.dtsi
index 9b7d9d04ded6..eb36d3662464 100644
--- a/arch/arm/boot/dts/qcom-pm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8226.dtsi
@@ -90,6 +90,16 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		pm8226_gpios: gpio@c000 {
+			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_gpios 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pm8226_1: pm8226@1 {
@@ -98,7 +108,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pm8226_spmi_regulators: pm8226-regulators {
+		pm8226_spmi_regulators: regulators {
 			compatible = "qcom,pm8226-regulators";
 		};
 
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 9cd49deb9fa7..cd957a1e7cdf 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -27,7 +27,7 @@
 			bias-pull-up;
 		};
 
-		usb_id: misc@900 {
+		usb_id: usb-detect@900 {
 			compatible = "qcom,pm8941-misc";
 			reg = <0x900>;
 			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
@@ -59,7 +59,7 @@
 			chg_otg: otg-vbus { };
 		};
 
-		pm8941_gpios: gpios@c000 {
+		pm8941_gpios: gpio@c000 {
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -101,37 +101,44 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
-			bat_temp {
-				reg = <VADC_LR_MUX1_BAT_THERM>;
+
+			adc-chan@6 {
+				reg = <VADC_VBAT_SNS>;
 			};
-			die_temp {
+
+			adc-chan@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			adc-chan@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			adc-chan@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_gnd {
+
+			adc-chan@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			adc-chan@f {
 				reg = <VADC_VDD_VADC>;
 			};
-			vbat_sns {
-				reg = <VADC_VBAT_SNS>;
+
+			adc-chan@30 {
+				reg = <VADC_LR_MUX1_BAT_THERM>;
 			};
 		};
 
-		pm8941_iadc: iadc@3600 {
+		pm8941_iadc: adc@3600 {
 			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
 			reg = <0x3600>;
 			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
 
-		pm8941_coincell: coincell@2800 {
+		pm8941_coincell: charger@2800 {
 			compatible = "qcom,pm8941-coincell";
 			reg = <0x2800>;
 			status = "disabled";
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi
index e77602e9f95c..2dd4c6aa71c9 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom-pma8084.dtsi
@@ -27,7 +27,7 @@
 			bias-pull-up;
 		};
 
-		pma8084_gpios: gpios@c000 {
+		pma8084_gpios: gpio@c000 {
 			compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -64,22 +64,27 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
-			die_temp {
+			adc-chan@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			adc-chan@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			adc-chan@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_buf_625mv {
+
+			adc-chan@c {
 				reg = <VADC_SPARE1>;
 			};
-			ref_gnd {
+
+			adc-chan@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			adc-chan@f {
 				reg = <VADC_VDD_VADC>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-pmx65.dtsi b/arch/arm/boot/dts/qcom-pmx65.dtsi
index abf229a8b75a..1c7fdf59c1f5 100644
--- a/arch/arm/boot/dts/qcom-pmx65.dtsi
+++ b/arch/arm/boot/dts/qcom-pmx65.dtsi
@@ -20,7 +20,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		pmx65_gpios: pinctrl@8800 {
+		pmx65_gpios: gpio@8800 {
 			compatible = "qcom,pmx65-gpio", "qcom,spmi-gpio";
 			reg = <0x8800>;
 			gpio-controller;
diff --git a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
index a4fa468a095f..ac8b4626ae9a 100644
--- a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
+++ b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
@@ -282,40 +282,25 @@
 };
 
 &tlmm {
-	pcie_ep_clkreq_default: pcie_ep_clkreq_default {
-		mux {
-			pins = "gpio56";
-			function = "pcie_clkreq";
-		};
-		config {
-			pins = "gpio56";
-			drive-strength = <2>;
-			bias-disable;
-		};
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
 	};
 
-	pcie_ep_perst_default: pcie_ep_perst_default {
-		mux {
-			pins = "gpio57";
-			function = "gpio";
-		};
-		config {
-			pins = "gpio57";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
 	};
 
-	pcie_ep_wake_default: pcie_ep_wake_default {
-		mux {
-			pins = "gpio53";
-			function = "gpio";
-		};
-		config {
-			pins = "gpio53";
-			drive-strength = <2>;
-			bias-disable;
-		};
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
 	};
 };
 
diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi
index c72540223fa9..f1c0dab40992 100644
--- a/arch/arm/boot/dts/qcom-sdx55.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx55.dtsi
@@ -559,6 +559,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 109>;
 		};
 
 		sram@1468f000 {
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
index 4cd405db5500..b073e0c63df4 100644
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -441,8 +441,8 @@
 			interrupt-controller;
 		};
 
-		imem@1468f000 {
-			compatible = "simple-mfd";
+		sram@1468f000 {
+			compatible = "qcom,sdx65-imem", "syscon", "simple-mfd";
 			reg = <0x1468f000 0x1000>;
 			ranges = <0x0 0x1468f000 0x1000>;
 			#address-cells = <1>;