MIPS: Ingenic: Fix bugs and add missing LED node for X1000.

1.The CU1000-Neo board actually uses X1000E instead of X1000,
  so the wrongly written "ingenic,x1000" in compatible should
  be changed to "ingenic,x1000e".
2.Adjust the order of nodes according to the corresponding
  address value.
3.Drop unnecessary node in "wlan_pwrseq".
4.Add the leds node to "cu1000-neo.dts".

Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

1 files changed, 56 insertions, 58 deletions

diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index 03abd94acd84..22a1066d637b 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -7,8 +7,8 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
-	compatible = "yna,cu1000-neo", "ingenic,x1000";
-	model = "YSH & ATIL General Board CU Neo";
+	compatible = "yna,cu1000-neo", "ingenic,x1000e";
+	model = "YSH & ATIL General Board CU1000-Neo";
 
 	aliases {
 		serial2 = &uart2;
@@ -23,20 +23,19 @@
 		reg = <0x0 0x04000000>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			gpios = <&gpb 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
 	wlan_pwrseq: msc1-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 
-		clocks = <&lpoclk>;
-		clock-names = "ext_clock";
-
 		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
 		post-power-on-delay-ms = <200>;
-
-		lpoclk: ap6212a {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
 	};
 };
 
@@ -53,6 +52,13 @@
 	ingenic,pwm-channels-mask = <0xfa>;
 };
 
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -61,43 +67,15 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pins_i2c0>;
 
-	ads7830@48 {
+	ads7830: adc@48 {
 		compatible = "ti,ads7830";
 		reg = <0x48>;
 	};
 };
 
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pins_uart2>;
-
-	status = "okay";
-};
-
-&mac {
-	phy-mode = "rmii";
-	phy-handle = <&lan8720a>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pins_mac>;
-
-	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
-
-	status = "okay";
-};
-
-&mdio {
+&msc0 {
 	status = "okay";
 
-	lan8720a: ethernet-phy@0 {
-		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-};
-
-&msc0 {
 	bus-width = <8>;
 	max-frequency = <50000000>;
 
@@ -105,26 +83,23 @@
 	pinctrl-0 = <&pins_msc0>;
 
 	non-removable;
-
-	status = "okay";
 };
 
 &msc1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
 	bus-width = <4>;
 	max-frequency = <50000000>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pins_msc1>;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	non-removable;
 
 	mmc-pwrseq = <&wlan_pwrseq>;
 
-	status = "okay";
-
 	ap6212a: wifi@1 {
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
@@ -137,23 +112,40 @@
 	};
 };
 
-&pinctrl {
-	pins_i2c0: i2c0 {
-		function = "i2c0";
-		groups = "i2c0-data";
-		bias-disable;
+&mac {
+	status = "okay";
+
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
 	};
+};
 
+&pinctrl {
 	pins_uart2: uart2 {
 		function = "uart2";
 		groups = "uart2-data-d";
-		bias-disable;
+		bias-pull-up;
 	};
 
-	pins_mac: mac {
-		function = "mac";
-		groups = "mac";
-		bias-disable;
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-pull-up;
 	};
 
 	pins_msc0: msc0 {
@@ -167,4 +159,10 @@
 		groups = "mmc1-1bit", "mmc1-4bit";
 		bias-disable;
 	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
 };