diff options
author | Stefan Popa <stefan.popa@analog.com> | 2019-02-27 18:14:22 +0200 |
---|---|---|
committer | Jonathan Cameron <Jonathan.Cameron@huawei.com> | 2019-04-04 20:19:42 +0100 |
commit | cede2f899d8f85baea32ff2e8a89a97aaac339b9 (patch) | |
tree | 50002066efa6d862f116a059a4819e627a420596 /drivers/iio/imu | |
parent | abbde2792999c9ad3514dd25d7f8d9a96034fe16 (diff) | |
download | linux-stable-cede2f899d8f85baea32ff2e8a89a97aaac339b9.tar.gz linux-stable-cede2f899d8f85baea32ff2e8a89a97aaac339b9.tar.bz2 linux-stable-cede2f899d8f85baea32ff2e8a89a97aaac339b9.zip |
iio: imu: adis16480: Add support for configurable drdy indicator
The FNCTIO_CTRL register provides configuration control for each I/O pin
(DIO1, DIO2, DIO3 and DIO4).
This patch adds the option to configure each DIOx pin as data ready
indicator with positive or negative polarity by reading the 'interrupts'
and 'interrupt-names' properties from the devicetree. The
'interrupt-names' property is optional, if it is not specified, then the
DIO1 pin is used as default data ready signal.
Although the factory default assigns DIO2 as data ready signal, in the
versions previous this patch, DIO1 pin was used. We should leave this
configuration as is, since some devices might be expecting the interrupt
on the wrong physical pin.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Diffstat (limited to 'drivers/iio/imu')
-rw-r--r-- | drivers/iio/imu/adis16480.c | 97 |
1 files changed, 95 insertions, 2 deletions
diff --git a/drivers/iio/imu/adis16480.c b/drivers/iio/imu/adis16480.c index a27fe208f3ae..98a23ac50266 100644 --- a/drivers/iio/imu/adis16480.c +++ b/drivers/iio/imu/adis16480.c @@ -9,6 +9,8 @@ * */ +#include <linux/bitfield.h> +#include <linux/of_irq.h> #include <linux/interrupt.h> #include <linux/delay.h> #include <linux/mutex.h> @@ -107,6 +109,14 @@ #define ADIS16480_FIR_COEF_C(x) ADIS16480_FIR_COEF(0x09, (x)) #define ADIS16480_FIR_COEF_D(x) ADIS16480_FIR_COEF(0x0B, (x)) +/* ADIS16480_REG_FNCTIO_CTRL */ +#define ADIS16480_DRDY_SEL_MSK GENMASK(1, 0) +#define ADIS16480_DRDY_SEL(x) FIELD_PREP(ADIS16480_DRDY_SEL_MSK, x) +#define ADIS16480_DRDY_POL_MSK BIT(2) +#define ADIS16480_DRDY_POL(x) FIELD_PREP(ADIS16480_DRDY_POL_MSK, x) +#define ADIS16480_DRDY_EN_MSK BIT(3) +#define ADIS16480_DRDY_EN(x) FIELD_PREP(ADIS16480_DRDY_EN_MSK, x) + struct adis16480_chip_info { unsigned int num_channels; const struct iio_chan_spec *channels; @@ -116,12 +126,26 @@ struct adis16480_chip_info { unsigned int accel_max_scale; }; +enum adis16480_int_pin { + ADIS16480_PIN_DIO1, + ADIS16480_PIN_DIO2, + ADIS16480_PIN_DIO3, + ADIS16480_PIN_DIO4 +}; + struct adis16480 { const struct adis16480_chip_info *chip_info; struct adis adis; }; +static const char * const adis16480_int_pin_names[4] = { + [ADIS16480_PIN_DIO1] = "DIO1", + [ADIS16480_PIN_DIO2] = "DIO2", + [ADIS16480_PIN_DIO3] = "DIO3", + [ADIS16480_PIN_DIO4] = "DIO4", +}; + #ifdef CONFIG_DEBUG_FS static ssize_t adis16480_show_firmware_revision(struct file *file, @@ -741,8 +765,17 @@ static int adis16480_stop_device(struct iio_dev *indio_dev) static int adis16480_enable_irq(struct adis *adis, bool enable) { - return adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, - enable ? BIT(3) : 0); + uint16_t val; + int ret; + + ret = adis_read_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, &val); + if (ret < 0) + return ret; + + val &= ~ADIS16480_DRDY_EN_MSK; + val |= ADIS16480_DRDY_EN(enable); + + return adis_write_reg_16(adis, ADIS16480_REG_FNCTIO_CTRL, val); } static int adis16480_initial_setup(struct iio_dev *indio_dev) @@ -826,6 +859,62 @@ static const struct adis_data adis16480_data = { .enable_irq = adis16480_enable_irq, }; +static int adis16480_config_irq_pin(struct device_node *of_node, + struct adis16480 *st) +{ + struct irq_data *desc; + enum adis16480_int_pin pin; + unsigned int irq_type; + uint16_t val; + int i, irq = 0; + + desc = irq_get_irq_data(st->adis.spi->irq); + if (!desc) { + dev_err(&st->adis.spi->dev, "Could not find IRQ %d\n", irq); + return -EINVAL; + } + + /* Disable data ready since the default after reset is on */ + val = ADIS16480_DRDY_EN(0); + + /* + * Get the interrupt from the devicetre by reading the interrupt-names + * property. If it is not specified, use DIO1 pin as default. + * According to the datasheet, the factory default assigns DIO2 as data + * ready signal. However, in the previous versions of the driver, DIO1 + * pin was used. So, we should leave it as is since some devices might + * be expecting the interrupt on the wrong physical pin. + */ + pin = ADIS16480_PIN_DIO1; + for (i = 0; i < ARRAY_SIZE(adis16480_int_pin_names); i++) { + irq = of_irq_get_byname(of_node, adis16480_int_pin_names[i]); + if (irq > 0) { + pin = i; + break; + } + } + + val |= ADIS16480_DRDY_SEL(pin); + + /* + * Get the interrupt line behaviour. The data ready polarity can be + * configured as positive or negative, corresponding to + * IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING respectively. + */ + irq_type = irqd_get_trigger_type(desc); + if (irq_type == IRQF_TRIGGER_RISING) { /* Default */ + val |= ADIS16480_DRDY_POL(1); + } else if (irq_type == IRQF_TRIGGER_FALLING) { + val |= ADIS16480_DRDY_POL(0); + } else { + dev_err(&st->adis.spi->dev, + "Invalid interrupt type 0x%x specified\n", irq_type); + return -EINVAL; + } + /* Write the data ready configuration to the FNCTIO_CTRL register */ + return adis_write_reg_16(&st->adis, ADIS16480_REG_FNCTIO_CTRL, val); +} + static int adis16480_probe(struct spi_device *spi) { const struct spi_device_id *id = spi_get_device_id(spi); @@ -853,6 +942,10 @@ static int adis16480_probe(struct spi_device *spi) if (ret) return ret; + ret = adis16480_config_irq_pin(spi->dev.of_node, st); + if (ret) + return ret; + ret = adis_setup_buffer_and_trigger(&st->adis, indio_dev, NULL); if (ret) return ret; |