mlxsw: Add support for transceiver modules reset

Implement support for ethtool_ops::reset in order to reset transceiver
modules. The module backing the netdev is reset when the 'ETH_RESET_PHY'
flag is set. After a successful reset, the flag is cleared by the driver
and other flags are ignored. This is in accordance with the interface
documentation:

"The reset() operation must clear the flags for the components which
were actually reset. On successful return, the flags indicate the
components which were not reset, either because they do not exist in the
hardware or because they cannot be reset independently. The driver must
never reset any components that were not requested."

Reset is useful in order to allow a module to transition out of a fault
state. From section 6.3.2.12 in CMIS 5.0: "Except for a power cycle, the
only exit path from the ModuleFault state is to perform a module reset
by taking an action that causes the ResetS transition signal to become
TRUE (see Table 6-11)".

An error is returned when the netdev is administratively up:

 # ip link set dev swp11 up

 # ethtool --reset swp11 phy
 ETHTOOL_RESET 0x40
 Cannot issue ETHTOOL_RESET: Invalid argument

 # ip link set dev swp11 down

 # ethtool --reset swp11 phy
 ETHTOOL_RESET 0x40
 Components reset:     0x40

An error is returned when the module is shared by multiple ports (split
ports) and the "phy-shared" flag is not set:

 # devlink port split swp11 count 4

 # ethtool --reset swp11s0 phy
 ETHTOOL_RESET 0x40
 Cannot issue ETHTOOL_RESET: Invalid argument

 # ethtool --reset swp11s0 phy-shared
 ETHTOOL_RESET 0x400000
 Components reset:     0x400000

 # devlink port unsplit swp11s0

 # ethtool --reset swp11 phy
 ETHTOOL_RESET 0x40
 Components reset:     0x40

An error is also returned when one of the ports using the module is
administratively up:

 # devlink port split swp11 count 4

 # ip link set dev swp11s1 up

 # ethtool --reset swp11s0 phy-shared
 ETHTOOL_RESET 0x400000
 Cannot issue ETHTOOL_RESET: Invalid argument

 # ip link set dev swp11s1 down

 # ethtool --reset swp11s0 phy-shared
 ETHTOOL_RESET 0x400000
 Components reset:     0x400000

Reset is performed by writing to the "rst" bit of the PMAOS register,
which instructs the firmware to assert the reset signal connected to the
module for a fixed amount of time.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 10 insertions, 0 deletions

diff --git a/drivers/net/ethernet/mellanox/mlxsw/minimal.c b/drivers/net/ethernet/mellanox/mlxsw/minimal.c
index a3eca0b56bbe..9644e9c486b8 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/minimal.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/minimal.c
@@ -136,11 +136,21 @@ mlxsw_m_get_module_eeprom_by_page(struct net_device *netdev,
 						   page, extack);
 }
 
+static int mlxsw_m_reset(struct net_device *netdev, u32 *flags)
+{
+	struct mlxsw_m_port *mlxsw_m_port = netdev_priv(netdev);
+	struct mlxsw_core *core = mlxsw_m_port->mlxsw_m->core;
+
+	return mlxsw_env_reset_module(netdev, core, mlxsw_m_port->module,
+				      flags);
+}
+
 static const struct ethtool_ops mlxsw_m_port_ethtool_ops = {
 	.get_drvinfo		= mlxsw_m_module_get_drvinfo,
 	.get_module_info	= mlxsw_m_get_module_info,
 	.get_module_eeprom	= mlxsw_m_get_module_eeprom,
 	.get_module_eeprom_by_page = mlxsw_m_get_module_eeprom_by_page,
+	.reset			= mlxsw_m_reset,
 };
 
 static int