diff options
author | John Garry <john.garry@huawei.com> | 2019-01-05 00:01:28 +0800 |
---|---|---|
committer | Martin K. Petersen <martin.petersen@oracle.com> | 2019-01-11 22:14:24 -0500 |
commit | cec9771d2e954650095aa37a6a97722c8194e7d2 (patch) | |
tree | 23dd7b0c9e3441ef9b73e1f72bf407f0f3736b03 /drivers/scsi/libsas | |
parent | 01929a65dfa13e18d89264ab1378854a91857e59 (diff) | |
download | linux-stable-cec9771d2e954650095aa37a6a97722c8194e7d2.tar.gz linux-stable-cec9771d2e954650095aa37a6a97722c8194e7d2.tar.bz2 linux-stable-cec9771d2e954650095aa37a6a97722c8194e7d2.zip |
scsi: libsas: Support SATA PHY connection rate unmatch fixing during discovery
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Diffstat (limited to 'drivers/scsi/libsas')
-rw-r--r-- | drivers/scsi/libsas/sas_expander.c | 20 |
1 files changed, 20 insertions, 0 deletions
diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c index 8817b8e6e507..83e3715d30e4 100644 --- a/drivers/scsi/libsas/sas_expander.c +++ b/drivers/scsi/libsas/sas_expander.c @@ -824,6 +824,26 @@ static struct domain_device *sas_ex_discover_end_dev( #ifdef CONFIG_SCSI_SAS_ATA if ((phy->attached_tproto & SAS_PROTOCOL_STP) || phy->attached_sata_dev) { + if (child->linkrate > parent->min_linkrate) { + struct sas_phy_linkrates rates = { + .maximum_linkrate = parent->min_linkrate, + .minimum_linkrate = parent->min_linkrate, + }; + int ret; + + pr_notice("ex %016llx phy%02d SATA device linkrate > min pathway connection rate, attempting to lower device linkrate\n", + SAS_ADDR(child->sas_addr), phy_id); + ret = sas_smp_phy_control(parent, phy_id, + PHY_FUNC_LINK_RESET, &rates); + if (ret) { + pr_err("ex %016llx phy%02d SATA device could not set linkrate (%d)\n", + SAS_ADDR(child->sas_addr), phy_id, ret); + goto out_free; + } + pr_notice("ex %016llx phy%02d SATA device set linkrate successfully\n", + SAS_ADDR(child->sas_addr), phy_id); + child->linkrate = child->min_linkrate; + } res = sas_get_ata_info(child, phy); if (res) goto out_free; |