diff options
author | Ryan Case <ryandcase@chromium.org> | 2019-01-07 17:58:35 -0800 |
---|---|---|
committer | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2019-01-08 16:57:47 +0100 |
commit | 9e06d55f7b856bfaf82036b50072600b21e52d20 (patch) | |
tree | ff77e9e19bd566a59dfe794a8c2b234ce583d446 /drivers/tty/serial/qcom_geni_serial.c | |
parent | 8fcf7a6569790fb5be4e5fa7d1a9f10734c6e8d8 (diff) | |
download | linux-stable-9e06d55f7b856bfaf82036b50072600b21e52d20.tar.gz linux-stable-9e06d55f7b856bfaf82036b50072600b21e52d20.tar.bz2 linux-stable-9e06d55f7b856bfaf82036b50072600b21e52d20.zip |
tty: serial: qcom_geni_serial: Remove use of *_relaxed() and mb()
A frequent side comment has been to remove the use of writel_relaxed,
readl_relaxed, and mb. This reduces driver complexity and the _relaxed
variants were not known to provide any noticeable performance benefit.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diffstat (limited to 'drivers/tty/serial/qcom_geni_serial.c')
-rw-r--r-- | drivers/tty/serial/qcom_geni_serial.c | 191 |
1 files changed, 80 insertions, 111 deletions
diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c index a72d6d9fb983..15c409d226c1 100644 --- a/drivers/tty/serial/qcom_geni_serial.c +++ b/drivers/tty/serial/qcom_geni_serial.c @@ -228,7 +228,7 @@ static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) if (uart_console(uport) || !uart_cts_enabled(uport)) { mctrl |= TIOCM_CTS; } else { - geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS); + geni_ios = readl(uport->membase + SE_GENI_IOS); if (!(geni_ios & IO2_DATA_IN)) mctrl |= TIOCM_CTS; } @@ -246,7 +246,7 @@ static void qcom_geni_serial_set_mctrl(struct uart_port *uport, if (!(mctrl & TIOCM_RTS)) uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; - writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); + writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); } static const char *qcom_geni_serial_get_type(struct uart_port *uport) @@ -275,9 +275,6 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport, unsigned int fifo_bits; unsigned long timeout_us = 20000; - /* Ensure polling is not re-ordered before the prior writes/reads */ - mb(); - if (uport->private_data) { port = to_dev_port(uport, uport); baud = port->baud; @@ -297,7 +294,7 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport, */ timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; while (timeout_us) { - reg = readl_relaxed(uport->membase + offset); + reg = readl(uport->membase + offset); if ((bool)(reg & field) == set) return true; udelay(10); @@ -310,7 +307,7 @@ static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) { u32 m_cmd; - writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); + writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); m_cmd = UART_START_TX << M_OPCODE_SHFT; writel(m_cmd, uport->membase + SE_GENI_M_CMD0); } @@ -323,13 +320,13 @@ static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_DONE_EN, true); if (!done) { - writel_relaxed(M_GENI_CMD_ABORT, uport->membase + + writel(M_GENI_CMD_ABORT, uport->membase + SE_GENI_M_CMD_CTRL_REG); irq_clear |= M_CMD_ABORT_EN; qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); } - writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_abort_rx(struct uart_port *uport) @@ -339,8 +336,8 @@ static void qcom_geni_serial_abort_rx(struct uart_port *uport) writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_ABORT, false); - writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); - writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); + writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); + writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); } #ifdef CONFIG_CONSOLE_POLL @@ -349,19 +346,13 @@ static int qcom_geni_serial_get_char(struct uart_port *uport) u32 rx_fifo; u32 status; - status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); - writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR); - - status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); - writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR); + status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); + writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR); - /* - * Ensure the writes to clear interrupts is not re-ordered after - * reading the data. - */ - mb(); + status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); + writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR); - status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); if (!(status & RX_FIFO_WC_MSK)) return NO_POLL_CHAR; @@ -374,13 +365,12 @@ static void qcom_geni_serial_poll_put_char(struct uart_port *uport, { struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, 1); WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_TX_FIFO_WATERMARK_EN, true)); - writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn); - writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(c, uport->membase + SE_GENI_TX_FIFOn); + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); qcom_geni_serial_poll_tx_done(uport); } #endif @@ -388,7 +378,7 @@ static void qcom_geni_serial_poll_put_char(struct uart_port *uport, #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch) { - writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn); + writel(ch, uport->membase + SE_GENI_TX_FIFOn); } static void @@ -407,7 +397,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, bytes_to_send++; } - writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); + writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); qcom_geni_serial_setup_tx(uport, bytes_to_send); for (i = 0; i < count; ) { size_t chars_to_write = 0; @@ -425,7 +415,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, chars_to_write = min_t(size_t, count - i, avail / 2); uart_console_write(uport, s + i, chars_to_write, qcom_geni_serial_wr_char); - writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase + + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); i += chars_to_write; } @@ -454,7 +444,7 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, else spin_lock_irqsave(&uport->lock, flags); - geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); + geni_status = readl(uport->membase + SE_GENI_STATUS); /* Cancel the current write to log the fault */ if (!locked) { @@ -464,11 +454,10 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); - writel_relaxed(M_CMD_ABORT_EN, uport->membase + + writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } - writel_relaxed(M_CMD_CANCEL_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) { /* * It seems we can't interrupt existing transfers if all data @@ -477,9 +466,8 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s, qcom_geni_serial_poll_tx_done(uport); if (uart_circ_chars_pending(&uport->state->xmit)) { - irq_en = readl_relaxed(uport->membase + - SE_GENI_M_IRQ_EN); - writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN, + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + writel(irq_en | M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } } @@ -583,12 +571,12 @@ static void qcom_geni_serial_start_tx(struct uart_port *uport) if (!qcom_geni_serial_tx_empty(uport)) return; - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; - writel_relaxed(port->tx_wm, uport->membase + + writel(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG); - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } } @@ -598,35 +586,28 @@ static void qcom_geni_serial_stop_tx(struct uart_port *uport) u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); irq_en &= ~M_CMD_DONE_EN; if (port->xfer_mode == GENI_SE_FIFO) { irq_en &= ~M_TX_FIFO_WATERMARK_EN; - writel_relaxed(0, uport->membase + + writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG); } - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); + status = readl(uport->membase + SE_GENI_STATUS); /* Possible stop tx is called multiple times. */ if (!(status & M_GENI_CMD_ACTIVE)) return; - /* - * Ensure cancel command write is not re-ordered before checking - * the status of the Primary Sequencer. - */ - mb(); - geni_se_cancel_m_cmd(&port->se); if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_CANCEL_EN, true)) { geni_se_abort_m_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, M_CMD_ABORT_EN, true); - writel_relaxed(M_CMD_ABORT_EN, uport->membase + - SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } - writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); } static void qcom_geni_serial_start_rx(struct uart_port *uport) @@ -635,26 +616,20 @@ static void qcom_geni_serial_start_rx(struct uart_port *uport) u32 status; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + status = readl(uport->membase + SE_GENI_STATUS); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_stop_rx(uport); - /* - * Ensure setup command write is not re-ordered before checking - * the status of the Secondary Sequencer. - */ - mb(); - geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); if (port->xfer_mode == GENI_SE_FIFO) { - irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; - writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); + writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } } @@ -666,31 +641,25 @@ static void qcom_geni_serial_stop_rx(struct uart_port *uport) u32 irq_clear = S_CMD_DONE_EN; if (port->xfer_mode == GENI_SE_FIFO) { - irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); - writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN); + writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); - writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN); + writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); } - status = readl_relaxed(uport->membase + SE_GENI_STATUS); + status = readl(uport->membase + SE_GENI_STATUS); /* Possible stop rx is called multiple times. */ if (!(status & S_GENI_CMD_ACTIVE)) return; - /* - * Ensure cancel command write is not re-ordered before checking - * the status of the Secondary Sequencer. - */ - mb(); - geni_se_cancel_s_cmd(&port->se); qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, S_GENI_CMD_CANCEL, false); - status = readl_relaxed(uport->membase + SE_GENI_STATUS); - writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); + status = readl(uport->membase + SE_GENI_STATUS); + writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); if (status & S_GENI_CMD_ACTIVE) qcom_geni_serial_abort_rx(uport); } @@ -704,7 +673,7 @@ static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop) u32 total_bytes; struct qcom_geni_serial_port *port = to_dev_port(uport, uport); - status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); word_cnt = status & RX_FIFO_WC_MSK; last_word_partial = status & RX_LAST; last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> @@ -734,7 +703,7 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, unsigned int chunk; int tail; - status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS); + status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS); /* Complete the current tx command before taking newly added data */ if (active) @@ -760,9 +729,9 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, qcom_geni_serial_setup_tx(uport, pending); port->tx_remaining = pending; - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); if (!(irq_en & M_TX_FIFO_WATERMARK_EN)) - writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN, + writel(irq_en | M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } @@ -795,14 +764,14 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done, * cleared it in qcom_geni_serial_isr it will have already reasserted * so we must clear it again here after our writes. */ - writel_relaxed(M_TX_FIFO_WATERMARK_EN, + writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); out_write_wakeup: if (!port->tx_remaining) { - irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); + irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); if (irq_en & M_TX_FIFO_WATERMARK_EN) - writel_relaxed(irq_en & ~M_TX_FIFO_WATERMARK_EN, + writel(irq_en & ~M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_EN); } @@ -826,12 +795,12 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) return IRQ_NONE; spin_lock_irqsave(&uport->lock, flags); - m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS); - s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS); - geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS); - m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN); - writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); - writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); + m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); + s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); + geni_status = readl(uport->membase + SE_GENI_STATUS); + m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); + writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); + writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) goto out_unlock; @@ -929,7 +898,7 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport) get_tx_fifo_size(port); set_rfr_wm(port); - writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT); + writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT); /* * Make an unconditional cancel on the main sequencer to reset * it else we could end up in data loss scenarios. @@ -1033,10 +1002,10 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport, ser_clk_cfg |= clk_div << CLK_DIV_SHFT; /* parity */ - tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG); - tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG); - rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG); - rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG); + tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG); + tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG); + rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG); + rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG); if (termios->c_cflag & PARENB) { tx_trans_cfg |= UART_TX_PAR_EN; rx_trans_cfg |= UART_RX_PAR_EN; @@ -1092,17 +1061,17 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport, uart_update_timeout(uport, termios->c_cflag, baud); if (!uart_console(uport)) - writel_relaxed(port->loopback, + writel(port->loopback, uport->membase + SE_UART_LOOPBACK_CFG); - writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); - writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); - writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); - writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); - writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); - writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); - writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); - writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); - writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); + writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); + writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); + writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); + writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); + writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); + writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); + writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); + writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); + writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); out_restart_rx: qcom_geni_serial_start_rx(uport); } @@ -1193,13 +1162,13 @@ static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); geni_se_select_mode(&se, GENI_SE_FIFO); - writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); - writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); - writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); - writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); - writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); - writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); - writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); + writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); + writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); + writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); + writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); + writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); + writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); + writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); dev->con->write = qcom_geni_serial_earlycon_write; dev->con->setup = NULL; |