usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)

Add support for control peripheral of EUD (Embedded USB Debugger) to
listen to events such as USB attach/detach, pet EUD to indicate software
is functional.Reusing the platform device kobj, sysfs entry 'enable' is
created to enable or disable EUD.

To enable the eud the following needs to be done
echo 1 > /sys/bus/platform/.../enable

To disable eud, following is the command
echo 0 > /sys/bus/platform/.../enable

Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Link: https://lore.kernel.org/r/0ac5c2b2c8e4ce4f4f342a08b48cfc61aeaf7ee8.1644339918.git.quic_schowdhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

3 files changed, 262 insertions, 0 deletions

diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index 8f1144359012..c9407b86790c 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig
@@ -137,6 +137,16 @@ config USB_APPLEDISPLAY
 	  Say Y here if you want to control the backlight of Apple Cinema
 	  Displays over USB. This driver provides a sysfs interface.
 
+config USB_QCOM_EUD
+	tristate "QCOM Embedded USB Debugger(EUD) Driver"
+	select USB_ROLE_SWITCH
+	help
+	  This module enables support for Qualcomm Technologies, Inc.
+	  Embedded USB Debugger (EUD). The EUD is a control peripheral
+	  which reports VBUS attach/detach events and has USB-based
+	  debug and trace capabilities. On selecting m, the module name
+	  that is built is qcom_eud.ko
+
 config APPLE_MFI_FASTCHARGE
 	tristate "Fast charge control for iOS devices"
 	select POWER_SUPPLY
diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
index 5f4e598573ab..35bdb4b6c3b6 100644
--- a/drivers/usb/misc/Makefile
+++ b/drivers/usb/misc/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_USB_ISIGHTFW)		+= isight_firmware.o
 obj-$(CONFIG_USB_LCD)			+= usblcd.o
 obj-$(CONFIG_USB_LD)			+= ldusb.o
 obj-$(CONFIG_USB_LEGOTOWER)		+= legousbtower.o
+obj-$(CONFIG_USB_QCOM_EUD)		+= qcom_eud.o
 obj-$(CONFIG_USB_TEST)			+= usbtest.o
 obj-$(CONFIG_USB_EHSET_TEST_FIXTURE)    += ehset.o
 obj-$(CONFIG_USB_TRANCEVIBRATOR)	+= trancevibrator.o
diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c
new file mode 100644
index 000000000000..f929bffdc5d1
--- /dev/null
+++ b/drivers/usb/misc/qcom_eud.c
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015-2021, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/sysfs.h>
+#include <linux/usb/role.h>
+
+#define EUD_REG_INT1_EN_MASK	0x0024
+#define EUD_REG_INT_STATUS_1	0x0044
+#define EUD_REG_CTL_OUT_1	0x0074
+#define EUD_REG_VBUS_INT_CLR	0x0080
+#define EUD_REG_CSR_EUD_EN	0x1014
+#define EUD_REG_SW_ATTACH_DET	0x1018
+#define EUD_REG_EUD_EN2        0x0000
+
+#define EUD_ENABLE		BIT(0)
+#define EUD_INT_PET_EUD	BIT(0)
+#define EUD_INT_VBUS		BIT(2)
+#define EUD_INT_SAFE_MODE	BIT(4)
+#define EUD_INT_ALL		(EUD_INT_VBUS | EUD_INT_SAFE_MODE)
+
+struct eud_chip {
+	struct device			*dev;
+	struct usb_role_switch		*role_sw;
+	void __iomem			*base;
+	void __iomem			*mode_mgr;
+	unsigned int			int_status;
+	int				irq;
+	bool				enabled;
+	bool				usb_attached;
+};
+
+static int enable_eud(struct eud_chip *priv)
+{
+	writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN);
+	writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE,
+			priv->base + EUD_REG_INT1_EN_MASK);
+	writel(1, priv->mode_mgr + EUD_REG_EUD_EN2);
+
+	return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE);
+}
+
+static void disable_eud(struct eud_chip *priv)
+{
+	writel(0, priv->base + EUD_REG_CSR_EUD_EN);
+	writel(0, priv->mode_mgr + EUD_REG_EUD_EN2);
+}
+
+static ssize_t enable_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct eud_chip *chip = dev_get_drvdata(dev);
+
+	return sysfs_emit(buf, "%d\n", chip->enabled);
+}
+
+static ssize_t enable_store(struct device *dev,
+		struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct eud_chip *chip = dev_get_drvdata(dev);
+	bool enable;
+	int ret;
+
+	if (kstrtobool(buf, &enable))
+		return -EINVAL;
+
+	if (enable) {
+		ret = enable_eud(chip);
+		if (!ret)
+			chip->enabled = enable;
+		else
+			disable_eud(chip);
+	} else {
+		disable_eud(chip);
+	}
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(enable);
+
+static struct attribute *eud_attrs[] = {
+	&dev_attr_enable.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(eud);
+
+static void usb_attach_detach(struct eud_chip *chip)
+{
+	u32 reg;
+
+	/* read ctl_out_1[4] to find USB attach or detach event */
+	reg = readl(chip->base + EUD_REG_CTL_OUT_1);
+	chip->usb_attached = reg & EUD_INT_SAFE_MODE;
+}
+
+static void pet_eud(struct eud_chip *chip)
+{
+	u32 reg;
+	int ret;
+
+	/* When the EUD_INT_PET_EUD in SW_ATTACH_DET is set, the cable has been
+	 * disconnected and we need to detach the pet to check if EUD is in safe
+	 * mode before attaching again.
+	 */
+	reg = readl(chip->base + EUD_REG_SW_ATTACH_DET);
+	if (reg & EUD_INT_PET_EUD) {
+		/* Detach & Attach pet for EUD */
+		writel(0, chip->base + EUD_REG_SW_ATTACH_DET);
+		/* Delay to make sure detach pet is done before attach pet */
+		ret = readl_poll_timeout(chip->base + EUD_REG_SW_ATTACH_DET,
+					reg, (reg == 0), 1, 100);
+		if (ret) {
+			dev_err(chip->dev, "Detach pet failed\n");
+			return;
+		}
+	}
+	/* Attach pet for EUD */
+	writel(EUD_INT_PET_EUD, chip->base + EUD_REG_SW_ATTACH_DET);
+}
+
+static irqreturn_t handle_eud_irq(int irq, void *data)
+{
+	struct eud_chip *chip = data;
+	u32 reg;
+
+	reg = readl(chip->base + EUD_REG_INT_STATUS_1);
+	switch (reg & EUD_INT_ALL) {
+	case EUD_INT_VBUS:
+		usb_attach_detach(chip);
+		return IRQ_WAKE_THREAD;
+	case EUD_INT_SAFE_MODE:
+		pet_eud(chip);
+		return IRQ_HANDLED;
+	default:
+		return IRQ_NONE;
+	}
+}
+
+static irqreturn_t handle_eud_irq_thread(int irq, void *data)
+{
+	struct eud_chip *chip = data;
+	int ret;
+
+	if (chip->usb_attached)
+		ret = usb_role_switch_set_role(chip->role_sw, USB_ROLE_DEVICE);
+	else
+		ret = usb_role_switch_set_role(chip->role_sw, USB_ROLE_HOST);
+	if (ret)
+		dev_err(chip->dev, "failed to set role switch\n");
+
+	/* set and clear vbus_int_clr[0] to clear interrupt */
+	writel(BIT(0), chip->base + EUD_REG_VBUS_INT_CLR);
+	writel(0, chip->base + EUD_REG_VBUS_INT_CLR);
+
+	return IRQ_HANDLED;
+}
+
+static void eud_role_switch_release(void *data)
+{
+	struct eud_chip *chip = data;
+
+	usb_role_switch_put(chip->role_sw);
+}
+
+static int eud_probe(struct platform_device *pdev)
+{
+	struct eud_chip *chip;
+	int ret;
+
+	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &pdev->dev;
+
+	ret = devm_add_action_or_reset(chip->dev, eud_role_switch_release, chip);
+	if (ret)
+		return dev_err_probe(chip->dev, ret,
+				"failed to add role switch release action\n");
+
+	chip->role_sw = usb_role_switch_get(&pdev->dev);
+	if (IS_ERR(chip->role_sw))
+		return dev_err_probe(chip->dev, PTR_ERR(chip->role_sw),
+					"failed to get role switch\n");
+
+	chip->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(chip->base))
+		return PTR_ERR(chip->base);
+
+	chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(chip->mode_mgr))
+		return PTR_ERR(chip->mode_mgr);
+
+	chip->irq = platform_get_irq(pdev, 0);
+	ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq,
+			handle_eud_irq_thread, IRQF_ONESHOT, NULL, chip);
+	if (ret)
+		return dev_err_probe(chip->dev, ret, "failed to allocate irq\n");
+
+	enable_irq_wake(chip->irq);
+
+	platform_set_drvdata(pdev, chip);
+
+	return 0;
+}
+
+static int eud_remove(struct platform_device *pdev)
+{
+	struct eud_chip *chip = platform_get_drvdata(pdev);
+
+	if (chip->enabled)
+		disable_eud(chip);
+
+	device_init_wakeup(&pdev->dev, false);
+	disable_irq_wake(chip->irq);
+
+	return 0;
+}
+
+static const struct of_device_id eud_dt_match[] = {
+	{ .compatible = "qcom,sc7280-eud" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, eud_dt_match);
+
+static struct platform_driver eud_driver = {
+	.probe	= eud_probe,
+	.remove	= eud_remove,
+	.driver	= {
+		.name = "qcom_eud",
+		.dev_groups = eud_groups,
+		.of_match_table = eud_dt_match,
+	},
+};
+module_platform_driver(eud_driver);
+
+MODULE_DESCRIPTION("QTI EUD driver");
+MODULE_LICENSE("GPL v2");