diff options
author | Yuanjiang Yu <yuanjiang.yu@unisoc.com> | 2018-11-14 17:07:06 +0800 |
---|---|---|
committer | Sebastian Reichel <sebastian.reichel@collabora.com> | 2018-12-06 01:04:30 +0100 |
commit | edcb1c0a3f6377d565a90795376ad6d4cb631d66 (patch) | |
tree | 608613f6f4b16d0ae9033ab7da3d31537752b797 /drivers | |
parent | 65c9fab7bc4b3a103bcac248e148af4a2efc17fe (diff) | |
download | linux-stable-edcb1c0a3f6377d565a90795376ad6d4cb631d66.tar.gz linux-stable-edcb1c0a3f6377d565a90795376ad6d4cb631d66.tar.bz2 linux-stable-edcb1c0a3f6377d565a90795376ad6d4cb631d66.zip |
power: supply: sc27xx: Add fuel gauge low voltage alarm
Add low voltage alarm support to make sure the battery capacity
more accurate in lower voltage stage.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/power/supply/sc27xx_fuel_gauge.c | 171 |
1 files changed, 170 insertions, 1 deletions
diff --git a/drivers/power/supply/sc27xx_fuel_gauge.c b/drivers/power/supply/sc27xx_fuel_gauge.c index 66f4db2650da..962d0f80babc 100644 --- a/drivers/power/supply/sc27xx_fuel_gauge.c +++ b/drivers/power/supply/sc27xx_fuel_gauge.c @@ -31,8 +31,11 @@ #define SC27XX_FGU_OCV 0x24 #define SC27XX_FGU_POCV 0x28 #define SC27XX_FGU_CURRENT 0x2c +#define SC27XX_FGU_LOW_OVERLOAD 0x34 #define SC27XX_FGU_CLBCNT_SETH 0x50 #define SC27XX_FGU_CLBCNT_SETL 0x54 +#define SC27XX_FGU_CLBCNT_DELTH 0x58 +#define SC27XX_FGU_CLBCNT_DELTL 0x5c #define SC27XX_FGU_CLBCNT_VALH 0x68 #define SC27XX_FGU_CLBCNT_VALL 0x6c #define SC27XX_FGU_CLBCNT_QMAXL 0x74 @@ -40,6 +43,11 @@ #define SC27XX_WRITE_SELCLB_EN BIT(0) #define SC27XX_FGU_CLBCNT_MASK GENMASK(15, 0) #define SC27XX_FGU_CLBCNT_SHIFT 16 +#define SC27XX_FGU_LOW_OVERLOAD_MASK GENMASK(12, 0) + +#define SC27XX_FGU_INT_MASK GENMASK(9, 0) +#define SC27XX_FGU_LOW_OVERLOAD_INT BIT(0) +#define SC27XX_FGU_CLBCNT_DELTA_INT BIT(2) #define SC27XX_FGU_CUR_BASIC_ADC 8192 #define SC27XX_FGU_SAMPLE_HZ 2 @@ -56,8 +64,10 @@ * @internal_resist: the battery internal resistance in mOhm * @total_cap: the total capacity of the battery in mAh * @init_cap: the initial capacity of the battery in mAh + * @alarm_cap: the alarm capacity * @init_clbcnt: the initial coulomb counter * @max_volt: the maximum constant input voltage in millivolt + * @min_volt: the minimum drained battery voltage in microvolt * @table_len: the capacity table length * @cur_1000ma_adc: ADC value corresponding to 1000 mA * @vol_1000mv_adc: ADC value corresponding to 1000 mV @@ -75,14 +85,18 @@ struct sc27xx_fgu_data { int internal_resist; int total_cap; int init_cap; + int alarm_cap; int init_clbcnt; int max_volt; + int min_volt; int table_len; int cur_1000ma_adc; int vol_1000mv_adc; struct power_supply_battery_ocv_table *cap_table; }; +static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity); + static const char * const sc27xx_charger_supply_name[] = { "sc2731_charger", "sc2720_charger", @@ -100,6 +114,11 @@ static int sc27xx_fgu_adc_to_voltage(struct sc27xx_fgu_data *data, int adc) return DIV_ROUND_CLOSEST(adc * 1000, data->vol_1000mv_adc); } +static int sc27xx_fgu_voltage_to_adc(struct sc27xx_fgu_data *data, int vol) +{ + return DIV_ROUND_CLOSEST(vol * data->vol_1000mv_adc, 1000); +} + /* * When system boots on, we can not read battery capacity from coulomb * registers, since now the coulomb registers are invalid. So we should @@ -428,6 +447,92 @@ static const struct power_supply_desc sc27xx_fgu_desc = { .external_power_changed = sc27xx_fgu_external_power_changed, }; +static void sc27xx_fgu_adjust_cap(struct sc27xx_fgu_data *data, int cap) +{ + data->init_cap = cap; + data->init_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, data->init_cap); +} + +static irqreturn_t sc27xx_fgu_interrupt(int irq, void *dev_id) +{ + struct sc27xx_fgu_data *data = dev_id; + int ret, cap, ocv, adc; + u32 status; + + mutex_lock(&data->lock); + + ret = regmap_read(data->regmap, data->base + SC27XX_FGU_INT_STS, + &status); + if (ret) + goto out; + + ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR, + status, status); + if (ret) + goto out; + + /* + * When low overload voltage interrupt happens, we should calibrate the + * battery capacity in lower voltage stage. + */ + if (!(status & SC27XX_FGU_LOW_OVERLOAD_INT)) + goto out; + + ret = sc27xx_fgu_get_capacity(data, &cap); + if (ret) + goto out; + + ret = sc27xx_fgu_get_vbat_ocv(data, &ocv); + if (ret) + goto out; + + /* + * If current OCV value is less than the minimum OCV value in OCV table, + * which means now battery capacity is 0%, and we should adjust the + * inititial capacity to 0. + */ + if (ocv <= data->cap_table[data->table_len - 1].ocv) { + sc27xx_fgu_adjust_cap(data, 0); + } else if (ocv <= data->min_volt) { + /* + * If current OCV value is less than the low alarm voltage, but + * current capacity is larger than the alarm capacity, we should + * adjust the inititial capacity to alarm capacity. + */ + if (cap > data->alarm_cap) { + sc27xx_fgu_adjust_cap(data, data->alarm_cap); + } else if (cap <= 0) { + int cur_cap; + + /* + * If current capacity is equal with 0 or less than 0 + * (some error occurs), we should adjust inititial + * capacity to the capacity corresponding to current OCV + * value. + */ + cur_cap = power_supply_ocv2cap_simple(data->cap_table, + data->table_len, + ocv); + sc27xx_fgu_adjust_cap(data, cur_cap); + } + + /* + * After adjusting the battery capacity, we should set the + * lowest alarm voltage instead. + */ + data->min_volt = data->cap_table[data->table_len - 1].ocv; + adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000); + regmap_update_bits(data->regmap, data->base + SC27XX_FGU_LOW_OVERLOAD, + SC27XX_FGU_LOW_OVERLOAD_MASK, adc); + } + +out: + mutex_unlock(&data->lock); + + power_supply_changed(data->battery); + return IRQ_HANDLED; +} + static irqreturn_t sc27xx_fgu_bat_detection(int irq, void *dev_id) { struct sc27xx_fgu_data *data = dev_id; @@ -509,7 +614,7 @@ static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data) { struct power_supply_battery_info info = { }; struct power_supply_battery_ocv_table *table; - int ret; + int ret, delta_clbcnt, alarm_adc; ret = power_supply_get_battery_info(data->battery, &info); if (ret) { @@ -520,6 +625,7 @@ static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data) data->total_cap = info.charge_full_design_uah / 1000; data->max_volt = info.constant_charge_voltage_max_uv / 1000; data->internal_resist = info.factory_internal_resistance_uohm / 1000; + data->min_volt = info.voltage_min_design_uv; /* * For SC27XX fuel gauge device, we only use one ocv-capacity @@ -537,6 +643,10 @@ static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data) return -ENOMEM; } + data->alarm_cap = power_supply_ocv2cap_simple(data->cap_table, + data->table_len, + data->min_volt); + power_supply_put_battery_info(data->battery, &info); ret = sc27xx_fgu_calibration(data); @@ -559,6 +669,50 @@ static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data) goto disable_fgu; } + ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR, + SC27XX_FGU_INT_MASK, SC27XX_FGU_INT_MASK); + if (ret) { + dev_err(data->dev, "failed to clear interrupt status\n"); + goto disable_clk; + } + + /* + * Set the voltage low overload threshold, which means when the battery + * voltage is lower than this threshold, the controller will generate + * one interrupt to notify. + */ + alarm_adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000); + ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_LOW_OVERLOAD, + SC27XX_FGU_LOW_OVERLOAD_MASK, alarm_adc); + if (ret) { + dev_err(data->dev, "failed to set fgu low overload\n"); + goto disable_clk; + } + + /* + * Set the coulomb counter delta threshold, that means when the coulomb + * counter change is multiples of the delta threshold, the controller + * will generate one interrupt to notify the users to update the battery + * capacity. Now we set the delta threshold as a counter value of 1% + * capacity. + */ + delta_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, 1); + + ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTL, + SC27XX_FGU_CLBCNT_MASK, delta_clbcnt); + if (ret) { + dev_err(data->dev, "failed to set low delta coulomb counter\n"); + goto disable_clk; + } + + ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTH, + SC27XX_FGU_CLBCNT_MASK, + delta_clbcnt >> SC27XX_FGU_CLBCNT_SHIFT); + if (ret) { + dev_err(data->dev, "failed to set high delta coulomb counter\n"); + goto disable_clk; + } + /* * Get the boot battery capacity when system powers on, which is used to * initialize the coulomb counter. After that, we can read the coulomb @@ -658,6 +812,21 @@ static int sc27xx_fgu_probe(struct platform_device *pdev) return ret; } + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "no irq resource specified\n"); + return irq; + } + + ret = devm_request_threaded_irq(data->dev, irq, NULL, + sc27xx_fgu_interrupt, + IRQF_NO_SUSPEND | IRQF_ONESHOT, + pdev->name, data); + if (ret) { + dev_err(data->dev, "failed to request fgu IRQ\n"); + return ret; + } + irq = gpiod_to_irq(data->gpiod); if (irq < 0) { dev_err(&pdev->dev, "failed to translate GPIO to IRQ\n"); |