diff options
| -rw-r--r-- | Documentation/admin-guide/mm/damon/lru_sort.rst | 4 | ||||
| -rw-r--r-- | Documentation/admin-guide/mm/damon/reclaim.rst | 4 | ||||
| -rw-r--r-- | Documentation/translations/zh_CN/admin-guide/mm/damon/reclaim.rst | 4 |
3 files changed, 6 insertions, 6 deletions
diff --git a/Documentation/admin-guide/mm/damon/lru_sort.rst b/Documentation/admin-guide/mm/damon/lru_sort.rst index c09cace80651..7b0775d281b4 100644 --- a/Documentation/admin-guide/mm/damon/lru_sort.rst +++ b/Documentation/admin-guide/mm/damon/lru_sort.rst @@ -54,7 +54,7 @@ that is built with ``CONFIG_DAMON_LRU_SORT=y``. To let sysadmins enable or disable it and tune for the given system, DAMON_LRU_SORT utilizes module parameters. That is, you can put ``damon_lru_sort.<parameter>=<value>`` on the kernel boot command line or write -proper values to ``/sys/modules/damon_lru_sort/parameters/<parameter>`` files. +proper values to ``/sys/module/damon_lru_sort/parameters/<parameter>`` files. Below are the description of each parameter. @@ -283,7 +283,7 @@ doesn't make progress and therefore the free memory rate becomes lower than 20%, it asks DAMON_LRU_SORT to do nothing again, so that we can fall back to the LRU-list based page granularity reclamation. :: - # cd /sys/modules/damon_lru_sort/parameters + # cd /sys/module/damon_lru_sort/parameters # echo 500 > hot_thres_access_freq # echo 120000000 > cold_min_age # echo 10 > quota_ms diff --git a/Documentation/admin-guide/mm/damon/reclaim.rst b/Documentation/admin-guide/mm/damon/reclaim.rst index 4f1479a11e63..d2ccd9c21b9a 100644 --- a/Documentation/admin-guide/mm/damon/reclaim.rst +++ b/Documentation/admin-guide/mm/damon/reclaim.rst @@ -46,7 +46,7 @@ that is built with ``CONFIG_DAMON_RECLAIM=y``. To let sysadmins enable or disable it and tune for the given system, DAMON_RECLAIM utilizes module parameters. That is, you can put ``damon_reclaim.<parameter>=<value>`` on the kernel boot command line or write -proper values to ``/sys/modules/damon_reclaim/parameters/<parameter>`` files. +proper values to ``/sys/module/damon_reclaim/parameters/<parameter>`` files. Below are the description of each parameter. @@ -251,7 +251,7 @@ therefore the free memory rate becomes lower than 20%, it asks DAMON_RECLAIM to do nothing again, so that we can fall back to the LRU-list based page granularity reclamation. :: - # cd /sys/modules/damon_reclaim/parameters + # cd /sys/module/damon_reclaim/parameters # echo 30000000 > min_age # echo $((1 * 1024 * 1024 * 1024)) > quota_sz # echo 1000 > quota_reset_interval_ms diff --git a/Documentation/translations/zh_CN/admin-guide/mm/damon/reclaim.rst b/Documentation/translations/zh_CN/admin-guide/mm/damon/reclaim.rst index bb185b7a9b9c..d14ba32f7788 100644 --- a/Documentation/translations/zh_CN/admin-guide/mm/damon/reclaim.rst +++ b/Documentation/translations/zh_CN/admin-guide/mm/damon/reclaim.rst @@ -45,7 +45,7 @@ DAMON_RECLAIM找到在特定时间内没有被访问的内存区域并分页。 为了让系统管理员启用或禁用它，并为给定的系统进行调整，DAMON_RECLAIM利用了模块参数。也就 是说，你可以把 ``damon_reclaim.<parameter>=<value>`` 放在内核启动命令行上，或者把 -适当的值写入 ``/sys/modules/damon_reclaim/parameters/<parameter>`` 文件。 +适当的值写入 ``/sys/module/damon_reclaim/parameters/<parameter>`` 文件。 下面是每个参数的描述。 @@ -214,7 +214,7 @@ nr_quota_exceeds 就开始真正的工作。如果DAMON_RECLAIM没有取得进展，因此空闲内存率低于20%，它会要求 DAMON_RECLAIM再次什么都不做，这样我们就可以退回到基于LRU列表的页面粒度回收了:: - # cd /sys/modules/damon_reclaim/parameters + # cd /sys/module/damon_reclaim/parameters # echo 30000000 > min_age # echo $((1 * 1024 * 1024 * 1024)) > quota_sz # echo 1000 > quota_reset_interval_ms |