diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt')
-rw-r--r-- | Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt | 82 |
1 files changed, 0 insertions, 82 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt deleted file mode 100644 index 7976e6c40a80..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt +++ /dev/null @@ -1,82 +0,0 @@ -STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge - -MIPID02 has two CSI-2 input ports, only one of those ports can be active at a -time. Active port input stream will be de-serialized and its content outputted -through PARALLEL output port. -CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second -input port is a single lane 800Mbps. Both ports support clock and data lane -polarity swap. First port also supports data lane swap. -PARALLEL output port has a maximum width of 12 bits. -Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444, -YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. - -Required Properties: -- compatible: shall be "st,st-mipid02" -- clocks: reference to the xclk input clock. -- clock-names: shall be "xclk". -- VDDE-supply: sensor digital IO supply. Must be 1.8 volts. -- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts. - -Optional Properties: -- reset-gpios: reference to the GPIO connected to the xsdn pin, if any. - This is an active low signal to the mipid02. - -Required subnodes: - - ports: A ports node with one port child node per device input and output - port, in accordance with the video interface bindings defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. The - port nodes are numbered as follows: - - Port Description - ----------------------------- - 0 CSI-2 first input port - 1 CSI-2 second input port - 2 PARALLEL output - -Endpoint node required property for CSI-2 connection is: -- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be -<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>. -Endpoint node optional property for CSI-2 connection is: -- lane-polarities: any lane can be inverted or not. - -Endpoint node required property for PARALLEL connection is: -- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>. -Endpoint node optional properties for PARALLEL connection are: -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. -LOW being the default. -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. -LOW being the default. - -Example: - -mipid02: csi2rx@14 { - compatible = "st,st-mipid02"; - reg = <0x14>; - status = "okay"; - clocks = <&clk_ext_camera_12>; - clock-names = "xclk"; - VDDE-supply = <&vdd>; - VDDIN-supply = <&vdd>; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - - ep0: endpoint { - data-lanes = <1 2>; - remote-endpoint = <&mipi_csi2_in>; - }; - }; - port@2 { - reg = <2>; - - ep2: endpoint { - bus-width = <8>; - hsync-active = <0>; - vsync-active = <0>; - remote-endpoint = <¶llel_out>; - }; - }; - }; -}; |