diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/faraday,ftpci100.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/faraday,ftpci100.txt | 135 |
1 files changed, 0 insertions, 135 deletions
diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt deleted file mode 100644 index 5f8cb4962f8d..000000000000 --- a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt +++ /dev/null @@ -1,135 +0,0 @@ -Faraday Technology FTPCI100 PCI Host Bridge - -This PCI bridge is found inside that Cortina Systems Gemini SoC platform and -is a generic IP block from Faraday Technology. It exists in two variants: -plain and dual PCI. The plain version embeds a cascading interrupt controller -into the host bridge. The dual version routes the interrupts to the host -chips interrupt controller. - -The host controller appear on the PCI bus with vendor ID 0x159b (Faraday -Technology) and product ID 0x4321. - -Mandatory properties: - -- compatible: ranging from specific to generic, should be one of - "cortina,gemini-pci", "faraday,ftpci100" - "cortina,gemini-pci-dual", "faraday,ftpci100-dual" - "faraday,ftpci100" - "faraday,ftpci100-dual" -- reg: memory base and size for the host bridge -- #address-cells: set to <3> -- #size-cells: set to <2> -- #interrupt-cells: set to <1> -- bus-range: set to <0x00 0xff> -- device_type, set to "pci" -- ranges: see pci.txt -- interrupt-map-mask: see pci.txt -- interrupt-map: see pci.txt -- dma-ranges: three ranges for the inbound memory region. The ranges must - be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB, - 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as - pre-fetchable. - -Optional properties: -- clocks: when present, this should contain the peripheral clock (PCLK) and the - PCI clock (PCICLK). If these are not present, they are assumed to be - hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz. -- clock-names: when present, this should contain "PCLK" for the peripheral - clock and "PCICLK" for the PCI-side clock. - -Mandatory subnodes: -- For "faraday,ftpci100" a node representing the interrupt-controller inside the - host bridge is mandatory. It has the following mandatory properties: - - interrupt: see interrupt-controller/interrupts.txt - - interrupt-controller: see interrupt-controller/interrupts.txt - - #address-cells: set to <0> - - #interrupt-cells: set to <1> - -I/O space considerations: - -The plain variant has 128MiB of non-prefetchable memory space, whereas the -"dual" variant has 64MiB. Take this into account when describing the ranges. - -Interrupt map considerations: - -The "dual" variant will get INT A, B, C, D from the system interrupt controller -and should point to respective interrupt in that controller in its -interrupt-map. - -The code which is the only documentation of how the Faraday PCI (the non-dual -variant) interrupts assigns the default interrupt mapping/swizzling has -typically been like this, doing the swizzling on the interrupt controller side -rather than in the interconnect: - -interrupt-map-mask = <0xf800 0 0 7>; -interrupt-map = - <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ - <0x4800 0 0 2 &pci_intc 1>, - <0x4800 0 0 3 &pci_intc 2>, - <0x4800 0 0 4 &pci_intc 3>, - <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ - <0x5000 0 0 2 &pci_intc 2>, - <0x5000 0 0 3 &pci_intc 3>, - <0x5000 0 0 4 &pci_intc 0>, - <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ - <0x5800 0 0 2 &pci_intc 3>, - <0x5800 0 0 3 &pci_intc 0>, - <0x5800 0 0 4 &pci_intc 1>, - <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ - <0x6000 0 0 2 &pci_intc 0>, - <0x6000 0 0 3 &pci_intc 1>, - <0x6000 0 0 4 &pci_intc 2>; - -Example: - -pci@50000000 { - compatible = "cortina,gemini-pci", "faraday,ftpci100"; - reg = <0x50000000 0x100>; - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */ - <26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */ - <27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */ - <28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */ - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - - bus-range = <0x00 0xff>; - ranges = /* 1MiB I/O space 0x50000000-0x500fffff */ - <0x01000000 0 0 0x50000000 0 0x00100000>, - /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */ - <0x02000000 0 0x58000000 0x58000000 0 0x08000000>; - - /* DMA ranges */ - dma-ranges = - /* 128MiB at 0x00000000-0x07ffffff */ - <0x02000000 0 0x00000000 0x00000000 0 0x08000000>, - /* 64MiB at 0x00000000-0x03ffffff */ - <0x02000000 0 0x00000000 0x00000000 0 0x04000000>, - /* 64MiB at 0x00000000-0x03ffffff */ - <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; - - interrupt-map-mask = <0xf800 0 0 7>; - interrupt-map = - <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ - <0x4800 0 0 2 &pci_intc 1>, - <0x4800 0 0 3 &pci_intc 2>, - <0x4800 0 0 4 &pci_intc 3>, - <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ - <0x5000 0 0 2 &pci_intc 2>, - <0x5000 0 0 3 &pci_intc 3>, - <0x5000 0 0 4 &pci_intc 0>, - <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ - <0x5800 0 0 2 &pci_intc 3>, - <0x5800 0 0 3 &pci_intc 0>, - <0x5800 0 0 4 &pci_intc 1>, - <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ - <0x6000 0 0 2 &pci_intc 0>, - <0x6000 0 0 3 &pci_intc 0>, - <0x6000 0 0 4 &pci_intc 0>; - pci_intc: interrupt-controller { - interrupt-parent = <&intcon>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; -}; |