diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml | 201 |
1 files changed, 201 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml new file mode 100644 index 000000000000..acea1cd444fd --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml @@ -0,0 +1,201 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX6 PCIe host controller + +maintainers: + - Lucas Stach <l.stach@pengutronix.de> + - Richard Zhu <hongxing.zhu@nxp.com> + +description: |+ + This PCIe host controller is based on the Synopsys DesignWare PCIe IP + and thus inherits all the common properties defined in snps,dw-pcie.yaml. + +allOf: + - $ref: /schemas/pci/snps,dw-pcie.yaml# + +properties: + compatible: + enum: + - fsl,imx6q-pcie + - fsl,imx6sx-pcie + - fsl,imx6qp-pcie + - fsl,imx7d-pcie + - fsl,imx8mq-pcie + + reg: + items: + - description: Data Bus Interface (DBI) registers. + - description: PCIe configuration space region. + + reg-names: + items: + - const: dbi + - const: config + + interrupts: + items: + - description: builtin MSI controller. + + interrupt-names: + items: + - const: msi + + clocks: + minItems: 3 + items: + - description: PCIe bridge clock. + - description: PCIe bus clock. + - description: PCIe PHY clock. + - description: Additional required clock entry for imx6sx-pcie, + imx8mq-pcie. + + clock-names: + minItems: 3 + items: + - const: pcie + - const: pcie_bus + - const: pcie_phy + - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie + + num-lanes: + const: 1 + + fsl,imx7d-pcie-phy: + $ref: /schemas/types.yaml#/definitions/phandle + description: A phandle to an fsl,imx7d-pcie-phy node. Additional + required properties for imx7d-pcie and imx8mq-pcie. + + power-domains: + items: + - description: The phandle pointing to the DISPLAY domain for + imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and + imx8mq-pcie. + - description: The phandle pointing to the PCIE_PHY power domains + for imx6sx-pcie. + + power-domain-names: + items: + - const: pcie + - const: pcie_phy + + resets: + maxItems: 3 + description: Phandles to PCIe-related reset lines exposed by SRC + IP block. Additional required by imx7d-pcie and imx8mq-pcie. + + reset-names: + items: + - const: pciephy + - const: apps + - const: turnoff + + fsl,tx-deemph-gen1: + description: Gen1 De-emphasis value (optional required). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + fsl,tx-deemph-gen2-3p5db: + description: Gen2 (3.5db) De-emphasis value (optional required). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + fsl,tx-deemph-gen2-6db: + description: Gen2 (6db) De-emphasis value (optional required). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 20 + + fsl,tx-swing-full: + description: Gen2 TX SWING FULL value (optional required). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 127 + + fsl,tx-swing-low: + description: TX launch amplitude swing_low value (optional required). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 127 + + fsl,max-link-speed: + description: Specify PCI Gen for link capability (optional required). + Note that the IMX6 LVDS clock outputs do not meet gen2 jitter + requirements and thus for gen2 capability a gen2 compliant clock + generator should be used and configured. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3, 4] + default: 1 + + reset-gpio: + description: Should specify the GPIO for controlling the PCI bus device + reset signal. It's not polarity aware and defaults to active-low reset + sequence (L=reset state, H=operation state) (optional required). + + reset-gpio-active-high: + description: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state) (optional required). + + vpcie-supply: + description: Should specify the regulator in charge of PCIe port power. + The regulator will be enabled when initializing the PCIe host and + disabled either as part of the init process or when shutting down + the host (optional required). + + vph-supply: + description: Should specify the regulator in charge of VPH one of + the three PCIe PHY powers. This regulator can be supplied by both + 1.8v and 3.3v voltage supplies (optional required). + +required: + - compatible + - reg + - reg-names + - "#address-cells" + - "#size-cells" + - device_type + - bus-range + - ranges + - num-lanes + - interrupts + - interrupt-names + - "#interrupt-cells" + - interrupt-map-mask + - interrupt-map + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pcie: pcie@1ffc000 { + compatible = "fsl,imx6q-pcie"; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0x00 0xff>; + ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>, + <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_PCIE_AXI>, + <&clks IMX6QDL_CLK_LVDS1_GATE>, + <&clks IMX6QDL_CLK_PCIE_REF_125M>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; +... |