summaryrefslogtreecommitdiffstats
path: root/Documentation/powerpc/dts-bindings/fsl
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/powerpc/dts-bindings/fsl')
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/board.txt29
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt67
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt21
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt41
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt18
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt15
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt45
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt58
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt24
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt51
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt60
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt70
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt22
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt21
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/diu.txt18
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/dma.txt127
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/gtm.txt31
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/guts.txt25
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/i2c.txt32
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/lbc.txt35
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/msi-pic.txt36
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/sata.txt29
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/sec.txt68
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/spi.txt24
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/ssi.txt38
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/tsec.txt69
-rw-r--r--Documentation/powerpc/dts-bindings/fsl/usb.txt59
27 files changed, 1133 insertions, 0 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
new file mode 100644
index 000000000000..74ae6f1cd2d6
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -0,0 +1,29 @@
+* Board Control and Status (BCSR)
+
+Required properties:
+
+ - device_type : Should be "board-control"
+ - reg : Offset and length of the register set for the device
+
+Example:
+
+ bcsr@f8000000 {
+ device_type = "board-control";
+ reg = <f8000000 8000>;
+ };
+
+* Freescale on board FPGA
+
+This is the memory-mapped registers for on board FPGA.
+
+Required properities:
+- compatible : should be "fsl,fpga-pixis".
+- reg : should contain the address and the lenght of the FPPGA register
+ set.
+
+Example (MPC8610HPCD):
+
+ board-control@e8000000 {
+ compatible = "fsl,fpga-pixis";
+ reg = <0xe8000000 32>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt
new file mode 100644
index 000000000000..088fc471e03a
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt
@@ -0,0 +1,67 @@
+* Freescale Communications Processor Module
+
+NOTE: This is an interim binding, and will likely change slightly,
+as more devices are supported. The QE bindings especially are
+incomplete.
+
+* Root CPM node
+
+Properties:
+- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
+- reg : A 48-byte region beginning with CPCR.
+
+Example:
+ cpm@119c0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+ reg = <119c0 30>;
+ }
+
+* Properties common to mulitple CPM/QE devices
+
+- fsl,cpm-command : This value is ORed with the opcode and command flag
+ to specify the device on which a CPM command operates.
+
+- fsl,cpm-brg : Indicates which baud rate generator the device
+ is associated with. If absent, an unused BRG
+ should be dynamically allocated. If zero, the
+ device uses an external clock rather than a BRG.
+
+- reg : Unless otherwise specified, the first resource represents the
+ scc/fcc/ucc registers, and the second represents the device's
+ parameter RAM region (if it has one).
+
+* Multi-User RAM (MURAM)
+
+The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
+
+Ranges must be set up subject to the following restrictions:
+
+- Children's reg nodes must be offsets from the start of all muram, even
+ if the user-data area does not begin at zero.
+- If multiple range entries are used, the difference between the parent
+ address and the child address must be the same in all, so that a single
+ mapping can cover them all while maintaining the ability to determine
+ CPM-side offsets with pointer subtraction. It is recommended that
+ multiple range entries not be used.
+- A child address of zero must be translatable, even if no reg resources
+ contain it.
+
+A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
+indicate the portion of muram that is usable by the OS for arbitrary
+purposes. The data node may have an arbitrary number of reg resources,
+all of which contribute to the allocatable muram pool.
+
+Example, based on mpc8272:
+ muram@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 10000>;
+
+ data@0 {
+ compatible = "fsl,cpm-muram-data";
+ reg = <0 2000 9800 800>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt
new file mode 100644
index 000000000000..4c7d45eaf025
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt
@@ -0,0 +1,21 @@
+* Baud Rate Generators
+
+Currently defined compatibles:
+fsl,cpm-brg
+fsl,cpm1-brg
+fsl,cpm2-brg
+
+Properties:
+- reg : There may be an arbitrary number of reg resources; BRG
+ numbers are assigned to these in order.
+- clock-frequency : Specifies the base frequency driving
+ the BRG.
+
+Example:
+ brg@119f0 {
+ compatible = "fsl,mpc8272-brg",
+ "fsl,cpm2-brg",
+ "fsl,cpm-brg";
+ reg = <119f0 10 115f0 10>;
+ clock-frequency = <d#25000000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt
new file mode 100644
index 000000000000..87bc6048667e
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt
@@ -0,0 +1,41 @@
+* I2C
+
+The I2C controller is expressed as a bus under the CPM node.
+
+Properties:
+- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
+- reg : On CPM2 devices, the second resource doesn't specify the I2C
+ Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
+ (typically 0x8afc 0x2).
+- #address-cells : Should be one. The cell is the i2c device address with
+ the r/w bit set to zero.
+- #size-cells : Should be zero.
+- clock-frequency : Can be used to set the i2c clock frequency. If
+ unspecified, a default frequency of 60kHz is being used.
+The following two properties are deprecated. They are only used by legacy
+i2c drivers to find the bus to probe:
+- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
+ the bus number is dynamically assigned by the i2c core.
+- linux,i2c-class : Can be used to override the i2c class. The class is used
+ by legacy i2c device drivers to find a bus in a specific context like
+ system management, video or sound. By default, I2C_CLASS_HWMON (1) is
+ being used. The definition of the classes can be found in
+ include/i2c/i2c.h
+
+Example, based on mpc823:
+
+ i2c@860 {
+ compatible = "fsl,mpc823-i2c",
+ "fsl,cpm1-i2c";
+ reg = <0x860 0x20 0x3c80 0x30>;
+ interrupts = <16>;
+ interrupt-parent = <&CPM_PIC>;
+ fsl,cpm-command = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtc@68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt
new file mode 100644
index 000000000000..8e3ee1681618
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt
@@ -0,0 +1,18 @@
+* Interrupt Controllers
+
+Currently defined compatibles:
+- fsl,cpm1-pic
+ - only one interrupt cell
+- fsl,pq1-pic
+- fsl,cpm2-pic
+ - second interrupt cell is level/sense:
+ - 2 is falling edge
+ - 8 is active low
+
+Example:
+ interrupt-controller@10c00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ reg = <10c00 80>;
+ compatible = "mpc8272-pic", "fsl,cpm2-pic";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt
new file mode 100644
index 000000000000..74bfda4bb824
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt
@@ -0,0 +1,15 @@
+* USB (Universal Serial Bus Controller)
+
+Properties:
+- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
+
+Example:
+ usb@11bc0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,cpm2-usb";
+ reg = <11b60 18 8b00 100>;
+ interrupts = <b 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-command = <2e600000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt
new file mode 100644
index 000000000000..0e4269446580
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt
@@ -0,0 +1,45 @@
+* Network
+
+Currently defined compatibles:
+- fsl,cpm1-scc-enet
+- fsl,cpm2-scc-enet
+- fsl,cpm1-fec-enet
+- fsl,cpm2-fcc-enet (third resource is GFEMR)
+- fsl,qe-enet
+
+Example:
+
+ ethernet@11300 {
+ device_type = "network";
+ compatible = "fsl,mpc8272-fcc-enet",
+ "fsl,cpm2-fcc-enet";
+ reg = <11300 20 8400 100 11390 1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <20 8>;
+ interrupt-parent = <&PIC>;
+ phy-handle = <&PHY0>;
+ fsl,cpm-command = <12000300>;
+ };
+
+* MDIO
+
+Currently defined compatibles:
+fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
+fsl,cpm2-mdio-bitbang (reg is port C registers)
+
+Properties for fsl,cpm2-mdio-bitbang:
+fsl,mdio-pin : pin of port C controlling mdio data
+fsl,mdc-pin : pin of port C controlling mdio clock
+
+Example:
+ mdio@10d40 {
+ device_type = "mdio";
+ compatible = "fsl,mpc8272ads-mdio-bitbang",
+ "fsl,mpc8272-mdio-bitbang",
+ "fsl,cpm2-mdio-bitbang";
+ reg = <10d40 14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ fsl,mdio-pin = <12>;
+ fsl,mdc-pin = <13>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt
new file mode 100644
index 000000000000..78790d58dc2c
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt
@@ -0,0 +1,58 @@
+* Freescale QUICC Engine module (QE)
+This represents qe module that is installed on PowerQUICC II Pro.
+
+NOTE: This is an interim binding; it should be updated to fit
+in with the CPM binding later in this document.
+
+Basically, it is a bus of devices, that could act more or less
+as a complete entity (UCC, USB etc ). All of them should be siblings on
+the "root" qe node, using the common properties from there.
+The description below applies to the qe of MPC8360 and
+more nodes and properties would be extended in the future.
+
+i) Root QE device
+
+Required properties:
+- compatible : should be "fsl,qe";
+- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+- reg : offset and length of the device registers.
+- bus-frequency : the clock frequency for QUICC Engine.
+
+Recommended properties
+- brg-frequency : the internal clock source frequency for baud-rate
+ generators in Hz.
+
+Example:
+ qe@e0100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,qe";
+ ranges = <0 e0100000 00100000>;
+ reg = <e0100000 480>;
+ brg-frequency = <0>;
+ bus-frequency = <179A7B00>;
+ }
+
+* Multi-User RAM (MURAM)
+
+Required properties:
+- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
+- mode : the could be "host" or "slave".
+- ranges : Should be defined as specified in 1) to describe the
+ translation of MURAM addresses.
+- data-only : sub-node which defines the address area under MURAM
+ bus that can be allocated as data/parameter
+
+Example:
+
+ muram@10000 {
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0 00010000 0000c000>;
+
+ data-only@0{
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0 c000>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt
new file mode 100644
index 000000000000..6c238f59b2a9
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt
@@ -0,0 +1,24 @@
+* Uploaded QE firmware
+
+ If a new firwmare has been uploaded to the QE (usually by the
+ boot loader), then a 'firmware' child node should be added to the QE
+ node. This node provides information on the uploaded firmware that
+ device drivers may need.
+
+ Required properties:
+ - id: The string name of the firmware. This is taken from the 'id'
+ member of the qe_firmware structure of the uploaded firmware.
+ Device drivers can search this string to determine if the
+ firmware they want is already present.
+ - extended-modes: The Extended Modes bitfield, taken from the
+ firmware binary. It is a 64-bit number represented
+ as an array of two 32-bit numbers.
+ - virtual-traps: The virtual traps, taken from the firmware binary.
+ It is an array of 8 32-bit numbers.
+
+Example:
+ firmware {
+ id = "Soft-UART";
+ extended-modes = <0 0>;
+ virtual-traps = <0 0 0 0 0 0 0 0>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt
new file mode 100644
index 000000000000..60984260207b
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt
@@ -0,0 +1,51 @@
+* Parallel I/O Ports
+
+This node configures Parallel I/O ports for CPUs with QE support.
+The node should reside in the "soc" node of the tree. For each
+device that using parallel I/O ports, a child node should be created.
+See the definition of the Pin configuration nodes below for more
+information.
+
+Required properties:
+- device_type : should be "par_io".
+- reg : offset to the register set and its length.
+- num-ports : number of Parallel I/O ports
+
+Example:
+par_io@1400 {
+ reg = <1400 100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "par_io";
+ num-ports = <7>;
+ ucc_pin@01 {
+ ......
+ };
+
+Note that "par_io" nodes are obsolete, and should not be used for
+the new device trees. Instead, each Par I/O bank should be represented
+via its own gpio-controller node:
+
+Required properties:
+- #gpio-cells : should be "2".
+- compatible : should be "fsl,<chip>-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank".
+- reg : offset to the register set and its length.
+- gpio-controller : node to identify gpio controllers.
+
+Example:
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt
new file mode 100644
index 000000000000..c5b43061db3a
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt
@@ -0,0 +1,60 @@
+* Pin configuration nodes
+
+Required properties:
+- linux,phandle : phandle of this node; likely referenced by a QE
+ device.
+- pio-map : array of pin configurations. Each pin is defined by 6
+ integers. The six numbers are respectively: port, pin, dir,
+ open_drain, assignment, has_irq.
+ - port : port number of the pin; 0-6 represent port A-G in UM.
+ - pin : pin number in the port.
+ - dir : direction of the pin, should encode as follows:
+
+ 0 = The pin is disabled
+ 1 = The pin is an output
+ 2 = The pin is an input
+ 3 = The pin is I/O
+
+ - open_drain : indicates the pin is normal or wired-OR:
+
+ 0 = The pin is actively driven as an output
+ 1 = The pin is an open-drain driver. As an output, the pin is
+ driven active-low, otherwise it is three-stated.
+
+ - assignment : function number of the pin according to the Pin Assignment
+ tables in User Manual. Each pin can have up to 4 possible functions in
+ QE and two options for CPM.
+ - has_irq : indicates if the pin is used as source of external
+ interrupts.
+
+Example:
+ ucc_pin@01 {
+ linux,phandle = <140001>;
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0 3 1 0 1 0 /* TxD0 */
+ 0 4 1 0 1 0 /* TxD1 */
+ 0 5 1 0 1 0 /* TxD2 */
+ 0 6 1 0 1 0 /* TxD3 */
+ 1 6 1 0 3 0 /* TxD4 */
+ 1 7 1 0 1 0 /* TxD5 */
+ 1 9 1 0 2 0 /* TxD6 */
+ 1 a 1 0 2 0 /* TxD7 */
+ 0 9 2 0 1 0 /* RxD0 */
+ 0 a 2 0 1 0 /* RxD1 */
+ 0 b 2 0 1 0 /* RxD2 */
+ 0 c 2 0 1 0 /* RxD3 */
+ 0 d 2 0 1 0 /* RxD4 */
+ 1 1 2 0 2 0 /* RxD5 */
+ 1 0 2 0 2 0 /* RxD6 */
+ 1 4 2 0 2 0 /* RxD7 */
+ 0 7 1 0 1 0 /* TX_EN */
+ 0 8 1 0 1 0 /* TX_ER */
+ 0 f 2 0 1 0 /* RX_DV */
+ 0 10 2 0 1 0 /* RX_ER */
+ 0 0 2 0 1 0 /* RX_CLK */
+ 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
+ 2 8 2 0 1 0>; /* GTX125 - CLK9 */
+ };
+
+
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
new file mode 100644
index 000000000000..e47734bee3f0
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
@@ -0,0 +1,70 @@
+* UCC (Unified Communications Controllers)
+
+Required properties:
+- device_type : should be "network", "hldc", "uart", "transparent"
+ "bisync", "atm", or "serial".
+- compatible : could be "ucc_geth" or "fsl_atm" and so on.
+- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+- pio-handle : The phandle for the Parallel I/O port configuration.
+- port-number : for UART drivers, the port number to use, between 0 and 3.
+ This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+ The port number is added to the minor number of the device. Unlike the
+ CPM UART driver, the port-number is required for the QE UART driver.
+- soft-uart : for UART drivers, if specified this means the QE UART device
+ driver should use "Soft-UART" mode, which is needed on some SOCs that have
+ broken UART hardware. Soft-UART is provided via a microcode upload.
+- rx-clock-name: the UCC receive clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- tx-clock-name: the UCC transmit clock source
+ "none": clock source is disabled
+ "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+ "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+The following two properties are deprecated. rx-clock has been replaced
+with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
+Drivers that currently use the deprecated properties should continue to
+do so, in order to support older device trees, but they should be updated
+to check for the new properties first.
+- rx-clock : represents the UCC receive clock source.
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+- tx-clock: represents the UCC transmit clock source;
+ 0x00 : clock source is disabled;
+ 0x1~0x10 : clock source is BRG1~BRG16 respectively;
+ 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+Required properties for network device_type:
+- mac-address : list of bytes representing the ethernet address.
+- phy-handle : The phandle for the PHY connected to this controller.
+
+Recommended properties:
+- phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+ Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+ "tbi", or "rtbi".
+
+Example:
+ ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <1>;
+ reg = <2000 200>;
+ interrupts = <a0 0>;
+ interrupt-parent = <700>;
+ mac-address = [ 00 04 9f 00 23 23 ];
+ rx-clock = "none";
+ tx-clock = "clk9";
+ phy-handle = <212000>;
+ phy-connection-type = "gmii";
+ pio-handle = <140001>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt
new file mode 100644
index 000000000000..c8f44d6bcbcf
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt
@@ -0,0 +1,22 @@
+* USB (Universal Serial Bus Controller)
+
+Required properties:
+- compatible : could be "qe_udc" or "fhci-hcd".
+- mode : the could be "host" or "slave".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example(slave):
+ usb@6c0 {
+ compatible = "qe_udc";
+ reg = <6c0 40>;
+ interrupts = <8b 0>;
+ interrupt-parent = <700>;
+ mode = "slave";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
new file mode 100644
index 000000000000..b35f3482e3e4
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
@@ -0,0 +1,21 @@
+* Serial
+
+Currently defined compatibles:
+- fsl,cpm1-smc-uart
+- fsl,cpm2-smc-uart
+- fsl,cpm1-scc-uart
+- fsl,cpm2-scc-uart
+- fsl,qe-uart
+
+Example:
+
+ serial@11a00 {
+ device_type = "serial";
+ compatible = "fsl,mpc8272-scc-uart",
+ "fsl,cpm2-scc-uart";
+ reg = <11a00 20 8000 100>;
+ interrupts = <28 8>;
+ interrupt-parent = <&PIC>;
+ fsl,cpm-brg = <1>;
+ fsl,cpm-command = <00800000>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/diu.txt b/Documentation/powerpc/dts-bindings/fsl/diu.txt
new file mode 100644
index 000000000000..deb35de70988
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/diu.txt
@@ -0,0 +1,18 @@
+* Freescale Display Interface Unit
+
+The Freescale DIU is a LCD controller, with proper hardware, it can also
+drive DVI monitors.
+
+Required properties:
+- compatible : should be "fsl-diu".
+- reg : should contain at least address and length of the DIU register
+ set.
+- Interrupts : one DIU interrupt should be describe here.
+
+Example (MPC8610HPCD):
+ display@2c000 {
+ compatible = "fsl,diu";
+ reg = <0x2c000 100>;
+ interrupts = <72 2>;
+ interrupt-parent = <&mpic>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt
new file mode 100644
index 000000000000..86826df00e64
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt
@@ -0,0 +1,127 @@
+* Freescale 83xx DMA Controller
+
+Freescale PowerPC 83xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma", where CHIP is the processor
+ (mpc8349, mpc8360, etc.) and the second is
+ "fsl,elo-dma"
+- reg : <registers mapping for DMA general status reg>
+- ranges : Should be defined as specified in 1) to describe the
+ DMA controller channels.
+- cell-index : controller index. 0 for controller @ 0x8100
+- interrupts : <interrupt mapping for DMA IRQ>
+- interrupt-parent : optional, if needed for interrupt mapping
+
+
+- DMA channel nodes:
+ - compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma-channel", where CHIP is the processor
+ (mpc8349, mpc8350, etc.) and the second is
+ "fsl,elo-dma-channel"
+ - reg : <registers mapping for channel>
+ - cell-index : dma channel index starts at 0.
+
+Optional properties:
+ - interrupts : <interrupt mapping for DMA channel IRQ>
+ (on 83xx this is expected to be identical to
+ the interrupts property of the parent node)
+ - interrupt-parent : optional, if needed for interrupt mapping
+
+Example:
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <82a8 4>;
+ ranges = <0 8100 1a4>;
+ interrupt-parent = <&ipic>;
+ interrupts = <47 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <0>;
+ reg = <0 80>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <1>;
+ reg = <80 80>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <2>;
+ reg = <100 80>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ cell-index = <3>;
+ reg = <180 80>;
+ };
+ };
+
+* Freescale 85xx/86xx DMA Controller
+
+Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma", where CHIP is the processor
+ (mpc8540, mpc8540, etc.) and the second is
+ "fsl,eloplus-dma"
+- reg : <registers mapping for DMA general status reg>
+- cell-index : controller index. 0 for controller @ 0x21000,
+ 1 for controller @ 0xc000
+- ranges : Should be defined as specified in 1) to describe the
+ DMA controller channels.
+
+- DMA channel nodes:
+ - compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-dma-channel", where CHIP is the processor
+ (mpc8540, mpc8560, etc.) and the second is
+ "fsl,eloplus-dma-channel"
+ - cell-index : dma channel index starts at 0.
+ - reg : <registers mapping for channel>
+ - interrupts : <interrupt mapping for DMA channel IRQ>
+ - interrupt-parent : optional, if needed for interrupt mapping
+
+Example:
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+ reg = <21300 4>;
+ ranges = <0 21100 200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <0 80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <14 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <80 80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <15 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <100 80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+ reg = <180 80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <17 2>;
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/gtm.txt b/Documentation/powerpc/dts-bindings/fsl/gtm.txt
new file mode 100644
index 000000000000..9a33efded4bc
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/gtm.txt
@@ -0,0 +1,31 @@
+* Freescale General-purpose Timers Module
+
+Required properties:
+ - compatible : should be
+ "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+ "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+ "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+ - reg : should contain gtm registers location and length (0x40).
+ - interrupts : should contain four interrupts.
+ - interrupt-parent : interrupt source phandle.
+ - clock-frequency : specifies the frequency driving the timer.
+
+Example:
+
+timer@500 {
+ compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+ reg = <0x500 0x40>;
+ interrupts = <90 8 78 8 84 8 72 8>;
+ interrupt-parent = <&ipic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+};
+
+timer@440 {
+ compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+};
diff --git a/Documentation/powerpc/dts-bindings/fsl/guts.txt b/Documentation/powerpc/dts-bindings/fsl/guts.txt
new file mode 100644
index 000000000000..9e7a2417dac5
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/guts.txt
@@ -0,0 +1,25 @@
+* Global Utilities Block
+
+The global utilities block controls power management, I/O device
+enabling, power-on-reset configuration monitoring, general-purpose
+I/O signal configuration, alternate function selection for multiplexed
+signals, and clock control.
+
+Required properties:
+
+ - compatible : Should define the compatible device type for
+ global-utilities.
+ - reg : Offset and length of the register set for the device.
+
+Recommended properties:
+
+ - fsl,has-rstcr : Indicates that the global utilities register set
+ contains a functioning "reset control register" (i.e. the board
+ is wired to reset upon setting the HRESET_REQ bit in this register).
+
+Example:
+ global-utilities@e0000 { /* global utilities block */
+ compatible = "fsl,mpc8548-guts";
+ reg = <e0000 1000>;
+ fsl,has-rstcr;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
new file mode 100644
index 000000000000..d0ab33e21fe6
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
@@ -0,0 +1,32 @@
+* I2C
+
+Required properties :
+
+ - device_type : Should be "i2c"
+ - reg : Offset and length of the register set for the device
+
+Recommended properties :
+
+ - compatible : Should be "fsl-i2c" for parts compatible with
+ Freescale I2C specifications.
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - dfsrr : boolean; if defined, indicates that this I2C device has
+ a digital filter sampling rate register
+ - fsl5200-clocking : boolean; if defined, indicated that this device
+ uses the FSL 5200 clocking mechanism.
+
+Example :
+ i2c@3000 {
+ interrupt-parent = <40000>;
+ interrupts = <1b 3>;
+ reg = <3000 18>;
+ device_type = "i2c";
+ compatible = "fsl-i2c";
+ dfsrr;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/lbc.txt b/Documentation/powerpc/dts-bindings/fsl/lbc.txt
new file mode 100644
index 000000000000..3300fec501c5
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/lbc.txt
@@ -0,0 +1,35 @@
+* Chipselect/Local Bus
+
+Properties:
+- name : Should be localbus
+- #address-cells : Should be either two or three. The first cell is the
+ chipselect number, and the remaining cells are the
+ offset into the chipselect.
+- #size-cells : Either one or two, depending on how large each chipselect
+ can be.
+- ranges : Each range corresponds to a single chipselect, and cover
+ the entire access window as configured.
+
+Example:
+ localbus@f0010100 {
+ compatible = "fsl,mpc8272-localbus",
+ "fsl,pq2-localbus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <f0010100 40>;
+
+ ranges = <0 0 fe000000 02000000
+ 1 0 f4500000 00008000>;
+
+ flash@0,0 {
+ compatible = "jedec-flash";
+ reg = <0 0 2000000>;
+ bank-width = <4>;
+ device-width = <1>;
+ };
+
+ board-control@1,0 {
+ reg = <1 0 20>;
+ compatible = "fsl,mpc8272ads-bcsr";
+ };
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt
new file mode 100644
index 000000000000..b26b91992c55
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt
@@ -0,0 +1,36 @@
+* Freescale MSI interrupt controller
+
+Reguired properities:
+- compatible : compatible list, contains 2 entries,
+ first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
+ etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
+ the parent type.
+- reg : should contain the address and the length of the shared message
+ interrupt register set.
+- msi-available-ranges: use <start count> style section to define which
+ msi interrupt can be used in the 256 msi interrupts. This property is
+ optional, without this, all the 256 MSI interrupts can be used.
+- interrupts : each one of the interrupts here is one entry per 32 MSIs,
+ and routed to the host interrupt controller. the interrupts should
+ be set as edge sensitive.
+- interrupt-parent: the phandle for the interrupt controller
+ that services interrupts for this device. for 83xx cpu, the interrupts
+ are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
+ to MPIC.
+
+Example:
+ msi@41600 {
+ compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
+ reg = <0x41600 0x80>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe0 0
+ 0xe1 0
+ 0xe2 0
+ 0xe3 0
+ 0xe4 0
+ 0xe5 0
+ 0xe6 0
+ 0xe7 0>;
+ interrupt-parent = <&mpic>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/sata.txt b/Documentation/powerpc/dts-bindings/fsl/sata.txt
new file mode 100644
index 000000000000..b46bcf46c3d8
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/sata.txt
@@ -0,0 +1,29 @@
+* Freescale 8xxx/3.0 Gb/s SATA nodes
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA port should have its own node.
+
+Required properties:
+- compatible : compatible list, contains 2 entries, first is
+ "fsl,CHIP-sata", where CHIP is the processor
+ (mpc8315, mpc8379, etc.) and the second is
+ "fsl,pq-sata"
+- interrupts : <interrupt mapping for SATA IRQ>
+- cell-index : controller index.
+ 1 for controller @ 0x18000
+ 2 for controller @ 0x19000
+ 3 for controller @ 0x1a000
+ 4 for controller @ 0x1b000
+
+Optional properties:
+- interrupt-parent : optional, if needed for interrupt mapping
+- reg : <registers mapping>
+
+Example:
+ sata@18000 {
+ compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+ reg = <0x18000 0x1000>;
+ cell-index = <1>;
+ interrupts = <2c 8>;
+ interrupt-parent = < &ipic >;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/sec.txt b/Documentation/powerpc/dts-bindings/fsl/sec.txt
new file mode 100644
index 000000000000..2b6f2d45c45a
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/sec.txt
@@ -0,0 +1,68 @@
+Freescale SoC SEC Security Engines
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+ SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0"
+- reg : Offset and length of the register set for the device
+- interrupts : the SEC's interrupt number
+- fsl,num-channels : An integer representing the number of channels
+ available.
+- fsl,channel-fifo-len : An integer representing the number of
+ descriptor pointers each channel fetch fifo can hold.
+- fsl,exec-units-mask : The bitmask representing what execution units
+ (EUs) are available. It's a single 32-bit cell. EU information
+ should be encoded following the SEC's Descriptor Header Dword
+ EU_SEL0 field documentation, i.e. as follows:
+
+ bit 0 = reserved - should be 0
+ bit 1 = set if SEC has the ARC4 EU (AFEU)
+ bit 2 = set if SEC has the DES/3DES EU (DEU)
+ bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A)
+ bit 4 = set if SEC has the random number generator EU (RNG)
+ bit 5 = set if SEC has the public key EU (PKEU)
+ bit 6 = set if SEC has the AES EU (AESU)
+ bit 7 = set if SEC has the Kasumi EU (KEU)
+ bit 8 = set if SEC has the CRC EU (CRCU)
+ bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B)
+
+remaining bits are reserved for future SEC EUs.
+
+- fsl,descriptor-types-mask : The bitmask representing what descriptors
+ are available. It's a single 32-bit cell. Descriptor type information
+ should be encoded following the SEC's Descriptor Header Dword DESC_TYPE
+ field documentation, i.e. as follows:
+
+ bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type
+ bit 1 = set if SEC supports the ipsec_esp descriptor type
+ bit 2 = set if SEC supports the common_nonsnoop desc. type
+ bit 3 = set if SEC supports the 802.11i AES ccmp desc. type
+ bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type
+ bit 5 = set if SEC supports the srtp descriptor type
+ bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type
+ bit 7 = set if SEC supports the pkeu_assemble descriptor type
+ bit 8 = set if SEC supports the aesu_key_expand_output desc.type
+ bit 9 = set if SEC supports the pkeu_ptmul descriptor type
+ bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type
+ bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type
+
+ ..and so on and so forth.
+
+Optional properties:
+
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example:
+
+ /* MPC8548E */
+ crypto@30000 {
+ compatible = "fsl,sec2.1", "fsl,sec2.0";
+ reg = <0x30000 0x10000>;
+ interrupts = <29 2>;
+ interrupt-parent = <&mpic>;
+ fsl,num-channels = <4>;
+ fsl,channel-fifo-len = <24>;
+ fsl,exec-units-mask = <0xfe>;
+ fsl,descriptor-types-mask = <0x12b0ebf>;
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt
new file mode 100644
index 000000000000..e7d9a344c4f4
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/spi.txt
@@ -0,0 +1,24 @@
+* SPI (Serial Peripheral Interface)
+
+Required properties:
+- cell-index : SPI controller index.
+- compatible : should be "fsl,spi".
+- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example:
+ spi@4c0 {
+ cell-index = <0>;
+ compatible = "fsl,spi";
+ reg = <4c0 40>;
+ interrupts = <82 0>;
+ interrupt-parent = <700>;
+ mode = "cpu";
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
new file mode 100644
index 000000000000..d100555d488a
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt
@@ -0,0 +1,38 @@
+Freescale Synchronous Serial Interface
+
+The SSI is a serial device that communicates with audio codecs. It can
+be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+Required properties:
+- compatible : compatible list, containing "fsl,ssi"
+- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
+- reg : offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and
+ level information for the interrupt. This should be
+ encoded based on the information in section 2)
+ depending on the type of interrupt controller you
+ have.
+- interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+- fsl,mode : the operating mode for the SSI interface
+ "i2s-slave" - I2S mode, SSI is clock slave
+ "i2s-master" - I2S mode, SSI is clock master
+ "lj-slave" - left-justified mode, SSI is clock slave
+ "lj-master" - l.j. mode, SSI is clock master
+ "rj-slave" - right-justified mode, SSI is clock slave
+ "rj-master" - r.j., SSI is clock master
+ "ac97-slave" - AC97 mode, SSI is clock slave
+ "ac97-master" - AC97 mode, SSI is clock master
+
+Optional properties:
+- codec-handle : phandle to a 'codec' node that defines an audio
+ codec connected to this SSI. This node is typically
+ a child of an I2C or other control node.
+
+Child 'codec' node required properties:
+- compatible : compatible list, contains the name of the codec
+
+Child 'codec' node optional properties:
+- clock-frequency : The frequency of the input clock, which typically
+ comes from an on-board dedicated oscillator.
diff --git a/Documentation/powerpc/dts-bindings/fsl/tsec.txt b/Documentation/powerpc/dts-bindings/fsl/tsec.txt
new file mode 100644
index 000000000000..583ef6b56c43
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/tsec.txt
@@ -0,0 +1,69 @@
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected. For each
+device that exists on this bus, a child node should be created. See
+the definition of the PHY node below for an example of how to define
+a PHY.
+
+Required properties:
+ - reg : Offset and length of the register set for the device
+ - compatible : Should define the compatible device type for the
+ mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
+
+Example:
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+
+* Gianfar-compatible ethernet nodes
+
+Required properties:
+
+ - device_type : Should be "network"
+ - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
+ - compatible : Should be "gianfar"
+ - reg : Offset and length of the register set for the device
+ - mac-address : List of bytes representing the ethernet address of
+ this controller
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - phy-handle : The phandle for the PHY connected to this ethernet
+ controller.
+ - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+ but unique to the all specified fixed-links, b is duplex - 0 half,
+ 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+ pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+
+Recommended properties:
+
+ - phy-connection-type : a string naming the controller/PHY interface type,
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
+ "tbi", or "rtbi". This property is only really needed if the connection
+ is of type "rgmii-id", as all other connection types are detected by
+ hardware.
+
+
+Example:
+ ethernet@24000 {
+ #size-cells = <0>;
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <24000 1000>;
+ mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <d 3 e 3 12 3>;
+ interrupt-parent = <40000>;
+ phy-handle = <2452000>
+ };
diff --git a/Documentation/powerpc/dts-bindings/fsl/usb.txt b/Documentation/powerpc/dts-bindings/fsl/usb.txt
new file mode 100644
index 000000000000..b00152402694
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/fsl/usb.txt
@@ -0,0 +1,59 @@
+Freescale SOC USB controllers
+
+The device node for a USB controller that is part of a Freescale
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "fsl-usb2-mph" for multi port host USB
+ controllers, or "fsl-usb2-dr" for dual role USB controllers
+ - phy_type : For multi port host USB controllers, should be one of
+ "ulpi", or "serial". For dual role USB controllers, should be
+ one of "ulpi", "utmi", "utmi_wide", or "serial".
+ - reg : Offset and length of the register set for the device
+ - port0 : boolean; if defined, indicates port0 is connected for
+ fsl-usb2-mph compatible controllers. Either this property or
+ "port1" (or both) must be defined for "fsl-usb2-mph" compatible
+ controllers.
+ - port1 : boolean; if defined, indicates port1 is connected for
+ fsl-usb2-mph compatible controllers. Either this property or
+ "port0" (or both) must be defined for "fsl-usb2-mph" compatible
+ controllers.
+ - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
+ controllers. Can be "host", "peripheral", or "otg". Default to
+ "host" if not defined for backward compatibility.
+
+Recommended properties :
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Example multi port host USB controller device node :
+ usb@22000 {
+ compatible = "fsl-usb2-mph";
+ reg = <22000 1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <700>;
+ interrupts = <27 1>;
+ phy_type = "ulpi";
+ port0;
+ port1;
+ };
+
+Example dual role USB controller device node :
+ usb@23000 {
+ compatible = "fsl-usb2-dr";
+ reg = <23000 1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <700>;
+ interrupts = <26 1>;
+ dr_mode = "otg";
+ phy = "ulpi";
+ };