diff options
Diffstat (limited to 'drivers/pinctrl/pinctrl-microchip-sgpio.c')
| -rw-r--r-- | drivers/pinctrl/pinctrl-microchip-sgpio.c | 69 |
1 files changed, 68 insertions, 1 deletions
diff --git a/drivers/pinctrl/pinctrl-microchip-sgpio.c b/drivers/pinctrl/pinctrl-microchip-sgpio.c index 53e4e6699c48..bbfe4394c557 100644 --- a/drivers/pinctrl/pinctrl-microchip-sgpio.c +++ b/drivers/pinctrl/pinctrl-microchip-sgpio.c @@ -64,11 +64,13 @@ struct sgpio_properties { #define SGPIO_LUTON_BIT_SOURCE GENMASK(11, 0) #define SGPIO_OCELOT_AUTO_REPEAT BIT(10) +#define SGPIO_OCELOT_SINGLE_SHOT BIT(11) #define SGPIO_OCELOT_PORT_WIDTH GENMASK(8, 7) #define SGPIO_OCELOT_CLK_FREQ GENMASK(19, 8) #define SGPIO_OCELOT_BIT_SOURCE GENMASK(23, 12) #define SGPIO_SPARX5_AUTO_REPEAT BIT(6) +#define SGPIO_SPARX5_SINGLE_SHOT BIT(7) #define SGPIO_SPARX5_PORT_WIDTH GENMASK(4, 3) #define SGPIO_SPARX5_CLK_FREQ GENMASK(19, 8) #define SGPIO_SPARX5_BIT_SOURCE GENMASK(23, 12) @@ -118,6 +120,8 @@ struct sgpio_priv { struct regmap *regs; const struct sgpio_properties *properties; spinlock_t lock; + /* protects the config register and single shot mode */ + struct mutex poll_lock; }; struct sgpio_port_addr { @@ -224,12 +228,64 @@ static inline void sgpio_configure_clock(struct sgpio_priv *priv, u32 clkfrq) sgpio_clrsetbits(priv, REG_SIO_CLOCK, 0, clr, set); } +static int sgpio_single_shot(struct sgpio_priv *priv) +{ + u32 addr = sgpio_get_addr(priv, REG_SIO_CONFIG, 0); + int ret, ret2; + u32 ctrl; + unsigned int single_shot; + unsigned int auto_repeat; + + switch (priv->properties->arch) { + case SGPIO_ARCH_LUTON: + /* not supported for now */ + return 0; + case SGPIO_ARCH_OCELOT: + single_shot = SGPIO_OCELOT_SINGLE_SHOT; + auto_repeat = SGPIO_OCELOT_AUTO_REPEAT; + break; + case SGPIO_ARCH_SPARX5: + single_shot = SGPIO_SPARX5_SINGLE_SHOT; + auto_repeat = SGPIO_SPARX5_AUTO_REPEAT; + break; + default: + return -EINVAL; + } + + /* + * Trigger immediate burst. This only works when auto repeat is turned + * off. Otherwise, the single shot bit will never be cleared by the + * hardware. Measurements showed that an update might take as long as + * the burst gap. On a LAN9668 this is about 50ms for the largest + * setting. + * After the manual burst, reenable the auto repeat mode again. + */ + mutex_lock(&priv->poll_lock); + ret = regmap_update_bits(priv->regs, addr, single_shot | auto_repeat, + single_shot); + if (ret) + goto out; + + ret = regmap_read_poll_timeout(priv->regs, addr, ctrl, + !(ctrl & single_shot), 100, 60000); + + /* reenable auto repeat mode even if there was an error */ + ret2 = regmap_update_bits(priv->regs, addr, auto_repeat, auto_repeat); +out: + mutex_unlock(&priv->poll_lock); + + return ret ?: ret2; +} + static int sgpio_output_set(struct sgpio_priv *priv, struct sgpio_port_addr *addr, int value) { unsigned int bit = SGPIO_SRC_BITS * addr->bit; + u32 reg = sgpio_get_addr(priv, REG_PORT_CONFIG, addr->port); + bool changed; u32 clr, set; + int ret; switch (priv->properties->arch) { case SGPIO_ARCH_LUTON: @@ -248,7 +304,16 @@ static int sgpio_output_set(struct sgpio_priv *priv, return -EINVAL; } - sgpio_clrsetbits(priv, REG_PORT_CONFIG, addr->port, clr, set); + ret = regmap_update_bits_check(priv->regs, reg, clr | set, set, + &changed); + if (ret) + return ret; + + if (changed) { + ret = sgpio_single_shot(priv); + if (ret) + return ret; + } return 0; } @@ -787,6 +852,7 @@ static int microchip_sgpio_register_bank(struct device *dev, gc->of_gpio_n_cells = 3; gc->base = -1; gc->ngpio = ngpios; + gc->can_sleep = !bank->is_input; if (bank->is_input && priv->properties->flags & SGPIO_FLAGS_HAS_IRQ) { int irq = fwnode_irq_get(fwnode, 0); @@ -847,6 +913,7 @@ static int microchip_sgpio_probe(struct platform_device *pdev) priv->dev = dev; spin_lock_init(&priv->lock); + mutex_init(&priv->poll_lock); reset = devm_reset_control_get_optional_shared(&pdev->dev, "switch"); if (IS_ERR(reset)) |