diff options
Diffstat (limited to 'drivers/usb/host')
-rw-r--r-- | drivers/usb/host/xhci-pci.c | 30 | ||||
-rw-r--r-- | drivers/usb/host/xhci-plat.c | 19 | ||||
-rw-r--r-- | drivers/usb/host/xhci-ring.c | 12 | ||||
-rw-r--r-- | drivers/usb/host/xhci.c | 100 | ||||
-rw-r--r-- | drivers/usb/host/xhci.h | 11 |
5 files changed, 148 insertions, 24 deletions
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 7f76c8a12f89..fd53c9ebd662 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -37,6 +37,9 @@ #define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI 0x8c31 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI 0x9c31 +#define PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI 0x22b5 +#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI 0xa12f +#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI 0x9d2f static const char hcd_name[] = "xhci_hcd"; @@ -133,6 +136,12 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) { xhci->quirks |= XHCI_SPURIOUS_REBOOT; } + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + (pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI || + pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI || + pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI)) { + xhci->quirks |= XHCI_PME_STUCK_QUIRK; + } if (pdev->vendor == PCI_VENDOR_ID_ETRON && pdev->device == PCI_DEVICE_ID_EJ168) { xhci->quirks |= XHCI_RESET_ON_RESUME; @@ -159,6 +168,21 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) "QUIRK: Resetting on resume"); } +/* + * Make sure PME works on some Intel xHCI controllers by writing 1 to clear + * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 + */ +static void xhci_pme_quirk(struct xhci_hcd *xhci) +{ + u32 val; + void __iomem *reg; + + reg = (void __iomem *) xhci->cap_regs + 0x80a4; + val = readl(reg); + writel(val | BIT(28), reg); + readl(reg); +} + /* called during probe() after chip reset completes */ static int xhci_pci_setup(struct usb_hcd *hcd) { @@ -283,6 +307,9 @@ static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) if (xhci->quirks & XHCI_COMP_MODE_QUIRK) pdev->no_d3cold = true; + if (xhci->quirks & XHCI_PME_STUCK_QUIRK) + xhci_pme_quirk(xhci); + return xhci_suspend(xhci, do_wakeup); } @@ -313,6 +340,9 @@ static int xhci_pci_resume(struct usb_hcd *hcd, bool hibernated) if (pdev->vendor == PCI_VENDOR_ID_INTEL) usb_enable_intel_xhci_ports(pdev); + if (xhci->quirks & XHCI_PME_STUCK_QUIRK) + xhci_pme_quirk(xhci); + retval = xhci_resume(xhci, hibernated); return retval; } diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c index 08d402b15482..0e11d61408ff 100644 --- a/drivers/usb/host/xhci-plat.c +++ b/drivers/usb/host/xhci-plat.c @@ -83,16 +83,6 @@ static int xhci_plat_probe(struct platform_device *pdev) if (irq < 0) return -ENODEV; - - if (of_device_is_compatible(pdev->dev.of_node, - "marvell,armada-375-xhci") || - of_device_is_compatible(pdev->dev.of_node, - "marvell,armada-380-xhci")) { - ret = xhci_mvebu_mbus_init_quirk(pdev); - if (ret) - return ret; - } - /* Initialize dma_mask and coherent_dma_mask to 32-bits */ ret = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); if (ret) @@ -127,6 +117,15 @@ static int xhci_plat_probe(struct platform_device *pdev) goto put_hcd; } + if (of_device_is_compatible(pdev->dev.of_node, + "marvell,armada-375-xhci") || + of_device_is_compatible(pdev->dev.of_node, + "marvell,armada-380-xhci")) { + ret = xhci_mvebu_mbus_init_quirk(pdev); + if (ret) + goto disable_clk; + } + ret = usb_add_hcd(hcd, irq, IRQF_SHARED); if (ret) goto disable_clk; diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 88da8d629820..5fb66db89e05 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1729,7 +1729,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci, if (!command) return; - ep->ep_state |= EP_HALTED; + ep->ep_state |= EP_HALTED | EP_RECENTLY_HALTED; ep->stopped_stream = stream_id; xhci_queue_reset_ep(xhci, command, slot_id, ep_index); @@ -1946,7 +1946,7 @@ static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - if (td->urb->actual_length != 0) { + if (td->urb_length_set) { /* Don't overwrite a previously set error code */ if ((*status == -EINPROGRESS || *status == 0) && @@ -1960,7 +1960,13 @@ static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td, td->urb->transfer_buffer_length; } } else { - /* Maybe the event was for the data stage? */ + /* + * Maybe the event was for the data stage? If so, update + * already the actual_length of the URB and flag it as + * set, so that it is not overwritten in the event for + * the last TRB. + */ + td->urb_length_set = true; td->urb->actual_length = td->urb->transfer_buffer_length - EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index ec8ac1674854..b06d1a53652d 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1338,6 +1338,12 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto exit; } + /* Reject urb if endpoint is in soft reset, queue must stay empty */ + if (xhci->devs[slot_id]->eps[ep_index].ep_state & EP_CONFIG_PENDING) { + xhci_warn(xhci, "Can't enqueue URB while ep is in soft reset\n"); + ret = -EINVAL; + } + if (usb_endpoint_xfer_isoc(&urb->ep->desc)) size = urb->number_of_packets; else @@ -2948,23 +2954,36 @@ void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci, } } -/* Called when clearing halted device. The core should have sent the control +/* Called after clearing a halted device. USB core should have sent the control * message to clear the device halt condition. The host side of the halt should - * already be cleared with a reset endpoint command issued when the STALL tx - * event was received. - * - * Context: in_interrupt + * already be cleared with a reset endpoint command issued immediately when the + * STALL tx event was received. */ void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; + struct usb_device *udev; + struct xhci_virt_device *virt_dev; + struct xhci_virt_ep *virt_ep; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_command *command; + unsigned int ep_index, ep_state; + unsigned long flags; + u32 ep_flag; xhci = hcd_to_xhci(hcd); + udev = (struct usb_device *) ep->hcpriv; + if (!ep->hcpriv) + return; + virt_dev = xhci->devs[udev->slot_id]; + ep_index = xhci_get_endpoint_index(&ep->desc); + virt_ep = &virt_dev->eps[ep_index]; + ep_state = virt_ep->ep_state; /* - * We might need to implement the config ep cmd in xhci 4.8.1 note: + * Implement the config ep command in xhci 4.6.8 additional note: * The Reset Endpoint Command may only be issued to endpoints in the * Halted state. If software wishes reset the Data Toggle or Sequence * Number of an endpoint that isn't in the Halted state, then software @@ -2972,9 +2991,72 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, * for the target endpoint. that is in the Stopped state. */ - /* For now just print debug to follow the situation */ - xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n", - ep->desc.bEndpointAddress); + if (ep_state & SET_DEQ_PENDING || ep_state & EP_RECENTLY_HALTED) { + virt_ep->ep_state &= ~EP_RECENTLY_HALTED; + xhci_dbg(xhci, "ep recently halted, no toggle reset needed\n"); + return; + } + + /* Only interrupt and bulk ep's use Data toggle, USB2 spec 5.5.4-> */ + if (usb_endpoint_xfer_control(&ep->desc) || + usb_endpoint_xfer_isoc(&ep->desc)) + return; + + ep_flag = xhci_get_endpoint_flag(&ep->desc); + + if (ep_flag == SLOT_FLAG || ep_flag == EP0_FLAG) + return; + + command = xhci_alloc_command(xhci, true, true, GFP_NOWAIT); + if (!command) { + xhci_err(xhci, "Could not allocate xHCI command structure.\n"); + return; + } + + spin_lock_irqsave(&xhci->lock, flags); + + /* block ringing ep doorbell */ + virt_ep->ep_state |= EP_CONFIG_PENDING; + + /* + * Make sure endpoint ring is empty before resetting the toggle/seq. + * Driver is required to synchronously cancel all transfer request. + * + * xhci 4.6.6 says we can issue a configure endpoint command on a + * running endpoint ring as long as it's idle (queue empty) + */ + + if (!list_empty(&virt_ep->ring->td_list)) { + dev_err(&udev->dev, "EP not empty, refuse reset\n"); + spin_unlock_irqrestore(&xhci->lock, flags); + goto cleanup; + } + + xhci_dbg(xhci, "Reset toggle/seq for slot %d, ep_index: %d\n", + udev->slot_id, ep_index); + + ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx); + if (!ctrl_ctx) { + xhci_err(xhci, "Could not get input context, bad type. virt_dev: %p, in_ctx %p\n", + virt_dev, virt_dev->in_ctx); + spin_unlock_irqrestore(&xhci->lock, flags); + goto cleanup; + } + xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx, + virt_dev->out_ctx, ctrl_ctx, + ep_flag, ep_flag); + xhci_endpoint_copy(xhci, command->in_ctx, virt_dev->out_ctx, ep_index); + + xhci_queue_configure_endpoint(xhci, command, command->in_ctx->dma, + udev->slot_id, false); + xhci_ring_cmd_db(xhci); + spin_unlock_irqrestore(&xhci->lock, flags); + + wait_for_completion(command->completion); + +cleanup: + virt_ep->ep_state &= ~EP_CONFIG_PENDING; + xhci_free_command(xhci, command); } static int xhci_check_streams_endpoint(struct xhci_hcd *xhci, diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 974514762a14..265ab1771d24 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1,3 +1,4 @@ + /* * xHCI host controller driver * @@ -88,9 +89,10 @@ struct xhci_cap_regs { #define HCS_IST(p) (((p) >> 0) & 0xf) /* bits 4:7, max number of Event Ring segments */ #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf) +/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */ /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */ -/* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */ -#define HCS_MAX_SCRATCHPAD(p) (((p) >> 27) & 0x1f) +/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */ +#define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f)) /* HCSPARAMS3 - hcs_params3 - bitmasks */ /* bits 0:7, Max U1 to U0 latency for the roothub ports */ @@ -863,6 +865,8 @@ struct xhci_virt_ep { #define EP_HAS_STREAMS (1 << 4) /* Transitioning the endpoint to not using streams, don't enqueue URBs */ #define EP_GETTING_NO_STREAMS (1 << 5) +#define EP_RECENTLY_HALTED (1 << 6) +#define EP_CONFIG_PENDING (1 << 7) /* ---- Related to URB cancellation ---- */ struct list_head cancelled_td_list; struct xhci_td *stopped_td; @@ -1288,6 +1292,8 @@ struct xhci_td { struct xhci_segment *start_seg; union xhci_trb *first_trb; union xhci_trb *last_trb; + /* actual_length of the URB has already been set */ + bool urb_length_set; }; /* xHCI command default timeout value */ @@ -1560,6 +1566,7 @@ struct xhci_hcd { #define XHCI_SPURIOUS_WAKEUP (1 << 18) /* For controllers with a broken beyond repair streams implementation */ #define XHCI_BROKEN_STREAMS (1 << 19) +#define XHCI_PME_STUCK_QUIRK (1 << 20) unsigned int num_active_eps; unsigned int limit_active_eps; /* There are two roothubs to keep track of bus suspend info for */ |