summaryrefslogtreecommitdiffstats
path: root/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/mac80211.h')
-rw-r--r--include/net/mac80211.h60
1 files changed, 60 insertions, 0 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index cc6035f1a2f1..7ceed99a05bc 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -829,6 +829,15 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
* @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
* @RX_FLAG_10MHZ: 10 MHz (half channel) was used
* @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
+ * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
+ * subframes instead of a one huge frame for performance reasons.
+ * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
+ * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
+ * the 3rd (last) one must not have this flag set. The flag is used to
+ * deal with retransmission/duplication recovery properly since A-MSDU
+ * subframes share the same sequence number. Reported subframes can be
+ * either regular MSDU or singly A-MSDUs. Subframes must not be
+ * interleaved with other frames.
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = BIT(0),
@@ -859,6 +868,7 @@ enum mac80211_rx_flags {
RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
RX_FLAG_10MHZ = BIT(28),
RX_FLAG_5MHZ = BIT(29),
+ RX_FLAG_AMSDU_MORE = BIT(30),
};
#define RX_FLAG_STBC_SHIFT 26
@@ -1492,6 +1502,15 @@ struct ieee80211_tx_control {
*
* @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
* only, to allow getting TBTT of a DTIM beacon.
+ *
+ * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
+ * and can cope with CCK rates in an aggregation session (e.g. by not
+ * using aggregation for such frames.)
+ *
+ * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
+ * for a single active channel while using channel contexts. When support
+ * is not enabled the default action is to disconnect when getting the
+ * CSA frame.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
@@ -1522,6 +1541,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25,
IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26,
IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27,
+ IEEE80211_HW_CHANCTX_STA_CSA = 1<<28,
};
/**
@@ -2666,6 +2686,10 @@ enum ieee80211_roc_type {
* zero using ieee80211_csa_is_complete() after the beacon has been
* transmitted and then call ieee80211_csa_finish().
*
+ * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
+ * information in bss_conf is set up and the beacon can be retrieved. A
+ * channel context is bound before this is called.
+ * @leave_ibss: Leave the IBSS again.
*/
struct ieee80211_ops {
void (*tx)(struct ieee80211_hw *hw,
@@ -2857,6 +2881,9 @@ struct ieee80211_ops {
void (*channel_switch_beacon)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct cfg80211_chan_def *chandef);
+
+ int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+ void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
};
/**
@@ -3920,6 +3947,25 @@ void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
void *data);
/**
+ * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This version can only be used while holding the RTNL.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw,
+ u32 iter_flags,
+ void (*iterator)(void *data,
+ u8 *mac,
+ struct ieee80211_vif *vif),
+ void *data);
+
+/**
* ieee80211_queue_work - add work onto the mac80211 workqueue
*
* Drivers and mac80211 use this to add work onto the mac80211 workqueue.
@@ -4525,4 +4571,18 @@ void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
struct cfg80211_wowlan_wakeup *wakeup,
gfp_t gfp);
+/**
+ * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
+ * @hw: pointer as obtained from ieee80211_alloc_hw()
+ * @vif: virtual interface
+ * @skb: frame to be sent from within the driver
+ * @band: the band to transmit on
+ * @sta: optional pointer to get the station to send the frame to
+ *
+ * Note: must be called under RCU lock
+ */
+bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif, struct sk_buff *skb,
+ int band, struct ieee80211_sta **sta);
+
#endif /* MAC80211_H */