| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When the hardware reduces the power to the minimum possible, the power
floor is notified via an interrupt.
This can happen when user space requests a power limit via powercap RAPL
interface, which forces the system to enter to the lowest power. This
power floor indication can be used as a hint to resort to other methods
of reducing power than via RAPL power limit.
Before power floor status can be read or the firmware can trigger
notifications regarding it, it needs to be configured via a mailbox
command. The actual power floor status is read via bit 39 of MMIO
offset 0x5B18 of the processor thermal PCI device.
To show the current power floor status and get notification
on a sysfs attribute, add 2 new attributes to
/sys/bus/pci/devices/0000\:00\:04.0/power_limits/
power_floor_enable : This attribute is present when power floor
notifications are supported. This attribute allows to enable/disable
power floor notifications.
power_floor_status : This attribute is present when power floor
notifications are supported. When enabled via power_floor_enable, this
attribute shows the current power floor status.
The power floor implementation provides interfaces which are called
from the sysfs callbacks to enable/disable and read power floor
status. It also provides two additional interfaces to check if the
current processor thermal device interrupt is for power floor status
and to send notifications to user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and documentation changes edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Prior to Meteor Lake processor generation, user space can pass workload
type request to the firmware. Then firmware can optimize power based on
the indicated workload type. User space also uses workload type requests
to implement its own heuristics.
The firmware in Meteor Lake processor generation is capable of predicting
workload type without software help.
To avoid duplicate processing, add a sysfs interface allowing user space
to obtain the workload hint from the firmware instead of trying to
predict the workload type by itself.
This workload hint is passed from the firmware via MMIO offset 0x5B18 of
the processor thermal PCI device. Before workload hints can be produced by
the firmware, it needs to be configured via a mailbox command. This
mailbox command turns ON the workload hint and it allows to program a
notification delay to control the rate of notifications.
The notification delay can be changed from user space vis sysfs.
Attribute group 'workload_hint' in sysfs is used for implementing the
workload hints interface between user space and the kernel.
It contains the following attributes:
workload_type_enable:
Enables/disables workload type hints from the firmware.
notification_delay_ms:
Notification delay in milliseconds.
workload_type_index:
The current workload type index predicted by the firmware (see
the documentation changes below for supported index values and
their meaning).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits, documentation edits, whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for DLVR (Digital Linear Voltage Regulator) attributes,
which can be used to control RFIM.
Here instead of "fivr" another directory "dlvr" is created with DLVR
attributes:
/sys/bus/pci/devices/0000:00:04.0/dlvr
├── dlvr_freq_mhz
├── dlvr_freq_select
├── dlvr_hardware_rev
├── dlvr_pll_busy
├── dlvr_rfim_enable
└── dlvr_spread_spectrum_pct
└── dlvr_control_mode
└── dlvr_control_lock
Attributes
dlvr_freq_mhz (RO):
Current DLVR PLL frequency in MHz.
dlvr_freq_select (RW):
Sets DLVR PLL clock frequency.
dlvr_hardware_rev (RO):
DLVR hardware revision.
dlvr_pll_busy (RO):
PLL can't accept frequency change when set.
dlvr_rfim_enable (RW):
0: Disable RF frequency hopping, 1: Enable RF frequency hopping.
dlvr_control_mode (RW):
Specifies how frequencies are spread. 0: Down spread, 1: Spread in Center.
dlvr_control_lock (RW):
1: future writes are ignored.
dlvr_spread_spectrum_pct (RW)
A write to this register updates the DLVR spread spectrum percent value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
| |
Remove struct thermal_bind_params because no one is using it for thermal
binding now.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230330104526.3196-1-rui.zhang@intel.com
|
| |
|
|
|
|
|
|
| |
Create a folder "thermal" under Documentation/admin-guide and move
intel_powerclamp documentation to this folder.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
It is possible that the system manufacturer locks down thermal tuning
beyond what is usually done on the given platform. In that case user
space calibration tools should not try to adjust the thermal
configuration of the system.
To allow user space to check if that is the case, add a new sysfs
attribute "production_mode" that will be present when the ACPI DCFG
method is present under the INT3400 device object in the ACPI Namespace.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Using a substitution pattern of "|copy|" without including
isonum.txt causes a doc build warning.
Using the symbol "©" itself is a better choice for those
who read .rst sources.
Reported by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 16c02447f3e1 ("Documentation: thermal: DPTF Documentation")
Suggested-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
| |
|
|
|
|
|
|
| |
Document Intel Dynamic Platform and Thermal Framework (DPTF)
ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The thermal ABI and the internal development details are described in:
Documentation/driver-api/thermal/sysfs-api.rst
Move the sysfs ABI description to Documentation/ABI, ensuring that
scripts/get_abi.pl will properly parse it.
While here, also update the thermal record in MAINTAINERS to point to
the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Changelog end subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\
| |
| |
| |
| |
| | |
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The hardware shutdown function was exported from kernel/reboot for
other subsystems to use. Logic is copied from the thermal_core. The
protection mutex is replaced by an atomic_t to allow calls also from
an IRQ context. Also the WARN() was replaced by pr_emerg() based on
discussions here:
https://lore.kernel.org/lkml/YJuPwAZroVZ%2Fw633@alley/
and here:
https://lore.kernel.org/linux-iommu/20210331093104.383705-4-geert+renesas@glider.be/
Use the exported API instead of implementing own just for the
thermal_core.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5531e89d9e710f5d10e7cdce3ee58957335b9e03.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Like many free software projects, Nouveau recently moved from Freenode
to OFTC. Update the reference.
v3: Add acks.
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210725150007.2818-1-alyssa@rosenzweig.io
|
| |
|
|
|
|
|
|
|
|
|
| |
documentation
Since thermal_notify_framework is no longer supported/implemented
remove the entry from sysfs-api.rst.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-4-thara.gopinath@linaro.org
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull documentation updates from Jonathan Corbet:
"It has been a relatively quiet cycle in docsland.
- As promised, the minimum Sphinx version to build the docs is now
1.7, and we have dropped support for Python 2 entirely. That
allowed the removal of a bunch of compatibility code.
- A set of treewide warning fixups from Mauro that I applied after it
became clear nobody else was going to deal with them.
- The automarkup mechanism can now create cross-references from
relative paths to RST files.
- More translations, typo fixes, and warning fixes"
* tag 'docs-5.12' of git://git.lwn.net/linux: (75 commits)
docs: kernel-hacking: be more civil
docs: Remove the Microsoft rhetoric
Documentation/admin-guide: kernel-parameters: Update nohlt section
doc/admin-guide: fix spelling mistake: "perfomance" -> "performance"
docs: Document cross-referencing using relative path
docs: Enable usage of relative paths to docs on automarkup
docs: thermal: fix spelling mistakes
Documentation: admin-guide: Update kvm/xen config option
docs: Make syscalls' helpers naming consistent
coding-style.rst: Avoid comma statements
Documentation: /proc/loadavg: add 3 more field descriptions
Documentation/submitting-patches: Add blurb about backtraces in commit messages
Docs: drop Python 2 support
Move our minimum Sphinx version to 1.7
Documentation: input: define ABS_PRESSURE/ABS_MT_PRESSURE resolution as grams
scripts/kernel-doc: add internal hyperlink to DOC: sections
Update Documentation/admin-guide/sysctl/fs.rst
docs: Update DTB format references
docs: zh_CN: add iio index.rst translation
docs/zh_CN: add iio ep93xx_adc.rst translation
...
|
| | |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210129132035.16967-1-f.suligoi@asem.it
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The code was reorganized in 2012 with the commit 0c01ebbfd3caf1.
The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.
With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.
As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.
In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.
If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.
Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.
Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The Energy Model (EM) can store power values in milli-Watts or in abstract
scale. This might cause issues in the subsystems which use the EM for
estimating the device power, such as:
- mixing of different scales in a subsystem which uses multiple
(cooling) devices (e.g. thermal Intelligent Power Allocation (IPA))
- assuming that energy [milli-Joules] can be derived from the EM power
values which might not be possible since the power scale doesn't have
to be in milli-Watts
To avoid misconfiguration add the requisite documentation to the EM and
related subsystems: EAS and IPA.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |/
|
|
|
|
|
|
|
| |
The sysfs stats for cooling devices shows the time_in_state in msec,
remove the unwanted usertime comment.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/d5461bdf9ab6b6fee7f28f538582edbb426aa077.1605004905.git.viresh.kumar@linaro.org
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200621133512.46311-1-grandmaster@al2klimov.de
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Despite being named with .rst extension, this file doesn't
match the ReST standard. It actually causes a crash at
Sphinx:
Sphinx parallel build error:
docutils.utils.SystemMessage: /devel/v4l/docs/Documentation/driver-api/thermal/cpu-idle-cooling.rst:69: (SEVERE/4) Unexpected section title.
Add needed markups for it to be properly parsed.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/7640755514809a7b5fe2756f3702613865877dcb.1592203650.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add cpu-idle-cooling.rst to the index list for user reference through
self-compiled htmldocs or online documentation tree of kernel.
Like: https://www.kernel.org/doc/html/latest/driver-api/thermal/index.html
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200429131109.80891-1-wenhu.wang@vivo.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
| |
|
|
|
|
| |
Signed-off-by: Sergey Vidishev <sergeyv@yandex-team.ru>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/2374188.AZIXMmL6Zy@sergeyv-box
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sphinx ('make htmldocs') stops with a SEVERE error:
Sphinx parallel build error:
SystemMessage: /home/rdunlap/lnx/next/linux-next-20200120/Documentation/driver-api/thermal/cpu-idle-cooling.rst:69: (SEVERE/4) Unexpected section title.
^
|
so fix the .rst file so that the SEVERE build error does not happen.
Also fix another minor formatting warning (unexpected unindent).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/712c1152-56b5-307f-b3f3-ed03a30b804a@infradead.org
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200104152107.11407-7-krzk@kernel.org
|
| |
|
|
|
|
|
|
|
|
|
| |
As we introduced the idle injection cooling device called
cpuidle_cooling, let's be consistent and rename the cpu_cooling to
cpufreq_cooling as this one mitigates with OPPs changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20191219225317.17158-3-daniel.lezcano@linaro.org
|
| |
|
|
|
|
|
|
|
|
| |
Provide some documentation for the idle injection cooling effect in
order to let people to understand the rational of the approach for the
idle injection CPU cooling device.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20191219225317.17158-1-daniel.lezcano@linaro.org
|
| |
|
|
|
|
|
|
|
|
| |
There are no users of netlink messages for thermal inside the kernel.
Remove the code and adjust the documentation.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/8ff02cf62186c7a54fff325fad40a2e9ca3affa6.1571656014.git.amit.kucheria@linaro.org
|
|
|
The file contents mostly describes driver internals.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
