summaryrefslogtreecommitdiffstats
path: root/arch/arc/boot/dts/hsdk.dts
Commit message (Collapse)AuthorAgeFilesLines
* ARC: [plat-hsdk]: Remove misplaced interrupt-cells propertyAlexey Brodkin2024-04-161-1/+0
| | | | | | | | | | | | | | | | | | "gmac" node stands for just an ordinary Ethernet controller, which is by no means a provider of interrupts, i.e. it doesn't serve as an interrupt controller, thus "#interrupt-cells" property doesn't belong to it and so we remove it. Fixes: ------------>8------------ DTC arch/arc/boot/dts/hsdk.dtb arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider' ------------>8------------ Reported-by: Vineet Gupta <vgupta@kernel.org> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@kernel.org>
* arc: dts: Harmonize EHCI/OHCI DT nodes nameSerge Semin2022-10-171-2/+2
| | | | | | | | | | | | | In accordance with the Generic EHCI/OHCI bindings the corresponding node name is suppose to comply with the Generic USB HCD DT schema, which requires the USB nodes to have the name acceptable by the regexp: "^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible nodes are correctly named. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Vineet Gupta <vgupta@kernel.org>
* ARC: dts: align SPI NOR node name with dtschemaKrzysztof Kozlowski2022-04-181-1/+1
| | | | | | | The node names should be generic and SPI NOR dtschema expects "flash". Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Vineet Gupta <vgupta@kernel.org>
* ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-idEvgeniy Didin2020-09-011-2/+2
| | | | | | | | | | | | | | | | | HSDK board has Micrel KSZ9031, recent commit bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") caused a breakdown of Ethernet. Using 'phy-mode = "rgmii"' is not correct because accodring RGMII specification it is necessary to have delay on RX (PHY to MAX) which is not generated in case of "rgmii". Using "rgmii-id" adds necessary delay and solves the issue. Also adding name of PHY placed on HSDK board. Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: HSDK: wireup perf irqVineet Gupta2020-08-161-0/+2
| | | | | | | | | Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up the perf interrupt, so enable that in DT. This is OK for old HSDK where this irq is ignored because pct irq is not wired up in hardware. Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Enable on-boardi SPI ADC ICEugeniy Paltsev2019-10-221-0/+15
| | | | | | | | HSDK board has adc108s102 SPI ADC IC installed, enable it. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Enable on-board SPI NOR flash ICEugeniy Paltsev2019-10-221-0/+8
| | | | | | | | HSDK board has sst26wf016b SPI NOR flash IC installed, enable it. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: enable DW SPI controllerEugeniy Paltsev2019-07-081-0/+14
| | | | | | | | | HSDK SoC has DW SPI controller. Enable it in preparation of enabling on-board SPI peripherals. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner2019-06-191-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ARC: [plat-hsdk] Get rid of inappropriate PHY settingsAlexey Brodkin2019-05-281-4/+0
| | | | | | | | | | | | | | | | | | | | Initial bring-up of the platform was done on FPGA prototype where TI's DP83867 PHY was used. And so some specific PHY options were added. Just to confirm this is what we get on FPGA prototype in the bootlog: | TI DP83867 stmmac-0:00: attached PHY driver [TI DP83867] ... On real board though we have Micrel KZS9031 PHY and we even have CONFIG_MICREL_PHY=y set in hsdk_defconfig. That's what we see in the bootlog: | Micrel KSZ9031 Gigabit PHY stmmac-0:00: ... So essentially all TI-related bits have to go away. Cc: Rob Herring <robh+dt@kernel.org> Acked-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Add support of Vivante GPUEugeniy Paltsev2019-05-281-0/+29
| | | | | | | | HSDK board has built-in Vivante GPU IP which works perfectly fine with Etnaviv driver, so let's use it. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: enable creg-gpio controllerEugeniy Paltsev2019-05-281-0/+8
| | | | | | | | | | HSDK SOC has CREG GPIO controller which can be used to control SPI chip select lines. Enable it in preparation of enabling SPI peripherals. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Add missing FIFO size entry in GMAC nodeJose Abreu2019-05-211-0/+3
| | | | | | | | | | | | | Add the binding for RX/TX fifo size of GMAC node. Cc: Joao Pinto <jpinto@synopsys.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Vineet Gupta <vgupta@synopsys.com> Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Add missing multicast filter bins number to GMAC nodeJose Abreu2019-05-211-0/+1
| | | | | | | | | | | | | | GMAC controller on HSDK boards supports 256 Hash Table size so we need to add the multicast filter bins property. This allows for the Hash filter to work properly using stmmac driver. Cc: Joao Pinto <jpinto@synopsys.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [hsdk] Make it easier to add PAE40 region to DTBVineet Gupta2019-04-021-6/+7
| | | | | | | | | | | | | 1. Bump top level address-cells/size-cells nodes to 2 (to ensure all down stream addresses are 64-bits, unless explicitly specified otherwise (in "soc" bus with all peripherals) 2. "memory" also specified with address/size 2 3. Add a commented reference for PAE40 region beyond 4GB physical address space Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Enable AXI DW DMAC supportEugeniy Paltsev2019-02-251-0/+27
| | | | | Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Add reset controller handle to manage USB resetEugeniy Paltsev2019-02-251-0/+2
| | | | | | | | DW USB controller on HSDK hangs sometimes after SW reset, so add reset handle to make possible to reset DW USB controller HW. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: DTB: [scripted] fix node name and address spellingAlexey Brodkin2019-02-251-2/+2
| | | | | | | | | | | | | | | | | | | | | 1. Remove "0x" prefix from unit-address of node names ----------------------->8------------------------ sed -i 's/@0x/@/g' arch/arc/boot/dts/*.dts* ----------------------->8------------------------ 2. Make all hex addresses lowercase: ----------------------->8------------------------ sed -i 's/@\([0-9A-Za-z]*\)/@\L\1/g' arch/arc/boot/dts/*.dts* sed -i 's/0x\([0-9A-Za-z]*\)/0x\L\1/g' arch/arc/boot/dts/*.dts* ----------------------->8------------------------ Inspired by [1] and the like. [1] http://kisskb.ellerman.id.au/kisskb/buildresult/13612017/ Reviewed-by: Rob Herring <robh+dt@kernel.org> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk] Enable DW APB GPIO supportEugeniy Paltsev2018-11-121-0/+15
| | | | | | | | | Enable GPIO support on HSDK. HSDK SoC includes Synopsys DesignWare DW_apb_gpio IP with 24 GPIOs mapped onto port A. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: dma [IOC]: mark DMA devices connected as dma-coherentEugeniy Paltsev2018-08-311-0/+4
| | | | | | | | Mark DMA devices on AXS103 and HSDK boards connected through IOC port as dma-coherent. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-axs*/plat-hsdk]: Allow U-Boot to pass MAC-address to the kernelAlexey Brodkin2018-08-271-1/+6
| | | | | | | | | | | | | | | | | | | | | | | Otherwise kernel uses random MAC which is not very conveniet. With that change in place use might set desired MAC in U-Boot with "setenv ethaddr 11:22:33:44:55:66", save environment and then from boot to boot the same MAC will be used by the kernel. One other note for this to happen it's required to pass board's .dtb in U-Boot's "bootm" command like that: ------------------->8----------------- bootm 0x82000000 - 0x84000000 ------------------->8----------------- Here 0x82000000 is location of uImage while 0x80000000 is location of either axs10x.dtb or hsdk.dtb previously loaded from SD-card, USB storage or TFTP server. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: stable@vger.kernel.org # 4.14 Cc: devicetree@vger.kernel.org Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Set initial core pll output frequencyEugeniy Paltsev2017-12-201-0/+8
| | | | | | | | | Set initial core pll output frequency specified in device tree to 1GHz. It will be applied at the core pll driver probing. Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk] Increase SDIO CIU frequency to 50000000HzEugeniy Paltsev2017-10-111-5/+6
| | | | | | | | | | | | | | | | With current SDIO CIU clock frequency (12500000Hz) DW MMC controller fails to initialize some SD cards (which don't support slow mode). So increase SDIO CIU frequency from 12500000Hz to 50000000Hz by switching from the default divisor value (div-by-8) to the minimum possible value of the divisor (div-by-2) in HSDK platform code. Reported-by: Vineet Gupta <vgupta@synopsys.com> Tested-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk]: Add reset controller node to manage ethernet resetEugeniy Paltsev2017-10-061-0/+9
| | | | | | | | DW ethernet controller on HSDK hangs sometimes after SW reset, so add reset node to make possible to reset DW ethernet controller HW. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk] use actual clk driver to manage cpu clkEugeniy Paltsev2017-10-031-2/+9
| | | | | | | | | | With corresponding clk driver now merged upstream, switch to it. - core_clk now represent the PLL (vs. fixed clk before) - input_clk represent the clk signal src for PLL (basically xtal) Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequencyEugeniy Paltsev2017-10-031-1/+11
| | | | | | | | | | | | | | | DW sdio controller has external ciu clock divider controlled via register in SDIO IP. Due to its unexpected default value (it should divide by 1 but it divides by 8) SDIO IP uses wrong ciu clock and works unstable So add temporary fix and change clock frequency from 100000000 to 12500000 Hz until we fix dw sdio driver itself. Fixes SNPS STAR 9001204800 Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC: [plat-hsdk] initial port for HSDK boardAlexey Brodkin2017-09-011-0/+189
This initial port adds support of ARC HS Development Kit board with some basic features such serial port, USB, SD/MMC and Ethernet. Essentially we run Linux kernel on all 4 cores (i.e. utilize SMP) and heavily use IO Coherency for speeding-up DMA-aware peripherals. Note as opposed to other ARC boards we link Linux kernel to 0x9000_0000 intentionally because cores 1 and 3 configured with DCCM situated at our more usual link base 0x8000_0000. We still can use memory region starting at 0x8000_0000 as we reallocate DCCM in our platform code. Note that PAE remapping for DMA clients does not work due to an RTL bug, so CREG_PAE register must be programmed to all zeroes, otherwise it will cause problems with DMA to/from peripherals even if PAE40 is not used. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-23 19:25:32 +0000