| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
| |
This is a driver for a block that generates master and bit clocks for
the I2S interface. It's separate from the PMUs that generate clocks for
the peripherals.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-14-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Apart from the clocks and resets, the PMU hardware also controls power
to peripherals that are on separate power islands. On MMP2, that's the
GC860 GPU and the SSPA audio interface, while on MMP3 also the camera
interface is on a separate island, along with the pair of GC2000 and GC300
GPUs and the SSPA.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-12-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The clk-of-mmp2 driver pretends that the clock outputs from the PLLs are
constant, but in fact they are configurable.
Add logic for obtaining the actual clock rates on MMP2 as well as MMP3.
There is no documentation for either SoC, but the "systemsetting" drivers
from Marvell GPL code dump provide some clue as far as MPMU registers on
MMP2 [1] and MMP3 [2] go.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp3-dell-ariel.git/tree/drivers/char/mmp2_systemsetting.c
[2] https://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp3-dell-ariel.git/tree/drivers/char/mmp3_systemsetting.c
A separate commit will adjust the clk-of-mmp2 driver.
Tested on a MMP3-based Dell Wyse 3020 as well as MMP2-based OLPC
XO-1.75 laptop.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-5-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Similar to MMP2, which this patch is based on. Known differencies from MMP2
are:
* Two PJ4B cores instead of one PJ4
* Tauros 3 L2 cache controller instead of Tauros 2
* A GIC interrupt controller optionally used instead of the MMP one
* A TWD local timer
* Different USB2 PHY
* A USB3 SS controller
* More interrupt muxes
Hard to tell what else is different, because documentation is not
available.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add initial clock support for Marvell PXA1928. The PXA1928 is a mobile
SOC and is similar to other MMP/PXA series of SOCs, so a lot of the
existing infrastructure is reused here.
Currently the PLLs are just fixed clocks, and not all leaf clocks are
implemented.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
|
|
|
|
|
|
| |
It adds the DT support for mmp2 clock subsystem.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
| |
It adds the DT support for pxa910 clock subsystem.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
| |
It adds the DT support for pxa168 clock subsystem.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
| |
Some clock control regsiter has bit to reset the cotroller.
So before enable the clock, we need deassert the reset pin.
Make use of reset controller framework to export reset interface
for device drivers, then device driver can control the reset action.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
|
| |
In order to support DT for mmp SOC clocks, it defines
some basic APIs which are shared by all mmp SOC clock
units.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some SOCes have this kind of the gate clock
1. There are some bits to control the gate not only one bit.
2. It is not always that "1" is to enable while "0" is to disable
when write register.
So we have to define the "mask", "enable_val", "disable_val" for
this kind of gate clock.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The clock type mix is a kind of clock combines "div" and "mux".
This kind of clock can not allow to change div first then
mux or change mux first or div.
The reason is
1. Some clock has frequency change bit. Each time want to change
the frequency, there are some operations based on this bit, and
these operations are time-cost.
Seperating div and mux change will make the process longer, and
waste more time.
2. Seperting the div and mux may generate middle clock that the
peripharals do not support. It may make the peripharals hang.
There are three kinds of this type of clock in all SOCes.
1. The clock has bit to trigger the frequency change.
2. Same as #1, but the operations for the bit is different
3. Do not have frequency change bit.
So this type of clock has implemented the callbacks
->determine_rate
->set_rate_and_parent
These callbacks can help to change the div and mux together.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
| |
Initialize the clocks for mmp2
Signed-off-by: Chao Xie <xiechao.mail@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
| |
Initialize the clocks for pxa910
Signed-off-by: Chao Xie <xiechao.mail@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
|
|
|
|
|
|
|
| |
Initialize the clocks for pxa168
Signed-off-by: Chao Xie <xiechao.mail@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
add mmp specific clocks including apbc cloks, apmu clocks,
and pll2, fraction clocks
Signed-off-by: Chao Xie <xiechao.mail@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|