1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
|
* Universal Flash Storage (UFS) Host Controller
UFSHC nodes are defined to describe on-chip UFS host controllers.
Each UFS controller instance should have its own node.
Required properties:
- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may
also list one or more of the following:
"qcom,msm8994-ufshc"
"qcom,msm8996-ufshc"
"qcom,ufshc"
- interrupts : <interrupt mapping for UFS host controller IRQ>
- reg : <registers mapping>
Optional properties:
- phys : phandle to UFS PHY node
- phy-names : the string "ufsphy" when is found in a node, along
with "phys" attribute, provides phandle to UFS PHY node
- vdd-hba-supply : phandle to UFS host controller supply regulator node
- vcc-supply : phandle to VCC supply regulator node
- vccq-supply : phandle to VCCQ supply regulator node
- vccq2-supply : phandle to VCCQ2 supply regulator node
- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V
or 2.7-3.6V. This boolean property when set, specifies
to use low voltage range of 1.7-1.95V. Note for external
UFS cards this property is invalid and valid VCC range is
always 2.7-3.6V.
- vcc-max-microamp : specifies max. load that can be drawn from vcc supply
- vccq-max-microamp : specifies max. load that can be drawn from vccq supply
- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply
- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator
- clocks : List of phandle and clock specifier pairs
- clock-names : List of clock input name strings sorted in the same
order as the clocks property.
- freq-table-hz : Array of <min max> operating frequencies stored in the same
order as the clocks property. If this property is not
defined or a value in the array is "0" then it is assumed
that the frequency is set by the parent clock or a
fixed rate clock source.
-lanes-per-direction : number of lanes available per direction - either 1 or 2.
Note that it is assume same number of lanes is used both
directions at once. If not specified, default is 2 lanes per direction.
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
Example:
ufshc@0xfc598000 {
compatible = "jedec,ufs-1.1";
reg = <0xfc598000 0x800>;
interrupts = <0 28 0>;
vdd-hba-supply = <&xxx_reg0>;
vdd-hba-fixed-regulator;
vcc-supply = <&xxx_reg1>;
vcc-supply-1p8;
vccq-supply = <&xxx_reg2>;
vccq2-supply = <&xxx_reg3>;
vcc-max-microamp = 500000;
vccq-max-microamp = 200000;
vccq2-max-microamp = 200000;
clocks = <&core 0>, <&ref 0>, <&iface 0>;
clock-names = "core_clk", "ref_clk", "iface_clk";
freq-table-hz = <100000000 200000000>, <0 0>, <0 0>;
phys = <&ufsphy1>;
phy-names = "ufsphy";
};
|
