summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
blob: 6ffb09be7a76a2703ed0cc81bf8ca96adbb94f25 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
Amlogic Meson GX DWC3 USB SoC controller

Required properties:
- compatible:	depending on the SoC this should contain one of:
			* amlogic,meson-axg-dwc3
			* amlogic,meson-gxl-dwc3
- clocks:	a handle for the "USB general" clock
- clock-names:	must be "usb_general"
- resets:	a handle for the shared "USB OTG" reset line
- reset-names:	must be "usb_otg"

Required child node:
A child node must exist to represent the core DWC3 IP block. The name of
the node is not important. The content of the node is defined in dwc3.txt.

PHY documentation is provided in the following places:
- Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt
- Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt

Example device nodes:
		usb0: usb@ff500000 {
			compatible = "amlogic,meson-axg-dwc3";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&clkc CLKID_USB>;
			clock-names = "usb_general";
			resets = <&reset RESET_USB_OTG>;
			reset-names = "usb_otg";

			dwc3: dwc3@ff500000 {
				compatible = "snps,dwc3";
				reg = <0x0 0xff500000 0x0 0x100000>;
				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
				dr_mode = "host";
				maximum-speed = "high-speed";
				snps,dis_u2_susphy_quirk;
				phys = <&usb3_phy>, <&usb2_phy0>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

Amlogic Meson G12A DWC3 USB SoC Controller Glue

The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
only.

A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY.

One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP.

The DWC3 Glue controls the PHY routing and power, an interrupt line is
connected to the Glue to serve as OTG ID change detection.

Required properties:
- compatible:	Should be "amlogic,meson-g12a-usb-ctrl"
- clocks:	a handle for the "USB" clock
- resets:	a handle for the shared "USB" reset line
- reg:		The base address and length of the registers
- interrupts:	the interrupt specifier for the OTG detection
- phys: 	handle to used PHYs on the system
	- a <0> phandle can be used if a PHY is not used
- phy-names:	names of the used PHYs on the system :
	- "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used
	- "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used
	- "usb3-phy0" for USB3 PHY if USB3_0 is used
- dr_mode:	should be "host", "peripheral", or "otg" depending on
	the usage and configuration of the OTG Capable port.
	- "host" and "peripheral" means a fixed Host or Device only connection
	- "otg" means the port can be used as both Host or Device and
	  be switched automatically using the OTG ID pin.

Optional properties:
- vbus-supply:	should be a phandle to the regulator controlling the VBUS
		power supply when used in OTG switchable mode

Required child nodes:

A child node must exist to represent the core DWC3 IP block. The name of
the node is not important. The content of the node is defined in dwc3.txt.

A child node must exist to represent the core DWC2 IP block. The name of
the node is not important. The content of the node is defined in dwc2.txt.

PHY documentation is provided in the following places:
- Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml
- Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb3-pcie-phy.yaml

Example device nodes:
	usb: usb@ffe09000 {
			compatible = "amlogic,meson-g12a-usb-ctrl";
			reg = <0x0 0xffe09000 0x0 0xa0>;
			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&clkc CLKID_USB>;
			resets = <&reset RESET_USB>;

			dr_mode = "otg";

			phys = <&usb2_phy0>, <&usb2_phy1>,
			       <&usb3_pcie_phy PHY_TYPE_USB3>;
			phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";

			dwc2: usb@ff400000 {
				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
				reg = <0x0 0xff400000 0x0 0x40000>;
				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
				clock-names = "ddr";
				phys = <&usb2_phy1>;
				dr_mode = "peripheral";
				g-rx-fifo-size = <192>;
				g-np-tx-fifo-size = <128>;
				g-tx-fifo-size = <128 128 16 16 16>;
			};

			dwc3: usb@ff500000 {
				compatible = "snps,dwc3";
				reg = <0x0 0xff500000 0x0 0x100000>;
				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
				dr_mode = "host";
				snps,dis_u2_susphy_quirk;
				snps,quirk-frame-length-adjustment;
			};
	};