summaryrefslogtreecommitdiffstats
path: root/drivers/media/pci/tw68/tw68-core.c
blob: 63f0b64057cbf88146a83091bb8b70ccc1857b72 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
/*
 *  tw68-core.c
 *  Core functions for the Techwell 68xx driver
 *
 *  Much of this code is derived from the cx88 and sa7134 drivers, which
 *  were in turn derived from the bt87x driver.  The original work was by
 *  Gerd Knorr; more recently the code was enhanced by Mauro Carvalho Chehab,
 *  Hans Verkuil, Andy Walls and many others.  Their work is gratefully
 *  acknowledged.  Full credit goes to them - any problems within this code
 *  are mine.
 *
 *  Copyright (C) 2009  William M. Brack
 *
 *  Refactored and updated to the latest v4l core frameworks:
 *
 *  Copyright (C) 2014 Hans Verkuil <hverkuil@xs4all.nl>
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation; either version 2 of the License, or
 *  (at your option) any later version.
 *
 *  This program is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 */

#include <linux/init.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/kmod.h>
#include <linux/sound.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/dma-mapping.h>
#include <linux/pm.h>

#include <media/v4l2-dev.h>
#include "tw68.h"
#include "tw68-reg.h"

MODULE_DESCRIPTION("v4l2 driver module for tw6800 based video capture cards");
MODULE_AUTHOR("William M. Brack");
MODULE_AUTHOR("Hans Verkuil <hverkuil@xs4all.nl>");
MODULE_LICENSE("GPL");

static unsigned int latency = UNSET;
module_param(latency, int, 0444);
MODULE_PARM_DESC(latency, "pci latency timer");

static unsigned int video_nr[] = {[0 ... (TW68_MAXBOARDS - 1)] = UNSET };
module_param_array(video_nr, int, NULL, 0444);
MODULE_PARM_DESC(video_nr, "video device number");

static unsigned int card[] = {[0 ... (TW68_MAXBOARDS - 1)] = UNSET };
module_param_array(card, int, NULL, 0444);
MODULE_PARM_DESC(card, "card type");

static atomic_t tw68_instance = ATOMIC_INIT(0);

/* ------------------------------------------------------------------ */

/*
 * Please add any new PCI IDs to: http://pci-ids.ucw.cz.  This keeps
 * the PCI ID database up to date.  Note that the entries must be
 * added under vendor 0x1797 (Techwell Inc.) as subsystem IDs.
 */
static const struct pci_device_id tw68_pci_tbl[] = {
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6800)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6801)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6804)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6816_1)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6816_2)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6816_3)},
	{PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, PCI_DEVICE_ID_6816_4)},
	{0,}
};

/* ------------------------------------------------------------------ */


/*
 * The device is given a "soft reset". According to the specifications,
 * after this "all register content remain unchanged", so we also write
 * to all specified registers manually as well (mostly to manufacturer's
 * specified reset values)
 */
static int tw68_hw_init1(struct tw68_dev *dev)
{
	/* Assure all interrupts are disabled */
	tw_writel(TW68_INTMASK, 0);		/* 020 */
	/* Clear any pending interrupts */
	tw_writel(TW68_INTSTAT, 0xffffffff);	/* 01C */
	/* Stop risc processor, set default buffer level */
	tw_writel(TW68_DMAC, 0x1600);

	tw_writeb(TW68_ACNTL, 0x80);	/* 218	soft reset */
	msleep(100);

	tw_writeb(TW68_INFORM, 0x40);	/* 208	mux0, 27mhz xtal */
	tw_writeb(TW68_OPFORM, 0x04);	/* 20C	analog line-lock */
	tw_writeb(TW68_HSYNC, 0);	/* 210	color-killer high sens */
	tw_writeb(TW68_ACNTL, 0x42);	/* 218	int vref #2, chroma adc off */

	tw_writeb(TW68_CROP_HI, 0x02);	/* 21C	Hactive m.s. bits */
	tw_writeb(TW68_VDELAY_LO, 0x12);/* 220	Mfg specified reset value */
	tw_writeb(TW68_VACTIVE_LO, 0xf0);
	tw_writeb(TW68_HDELAY_LO, 0x0f);
	tw_writeb(TW68_HACTIVE_LO, 0xd0);

	tw_writeb(TW68_CNTRL1, 0xcd);	/* 230	Wide Chroma BPF B/W
					 *	Secam reduction, Adap comb for
					 *	NTSC, Op Mode 1 */

	tw_writeb(TW68_VSCALE_LO, 0);	/* 234 */
	tw_writeb(TW68_SCALE_HI, 0x11);	/* 238 */
	tw_writeb(TW68_HSCALE_LO, 0);	/* 23c */
	tw_writeb(TW68_BRIGHT, 0);	/* 240 */
	tw_writeb(TW68_CONTRAST, 0x5c);	/* 244 */
	tw_writeb(TW68_SHARPNESS, 0x51);/* 248 */
	tw_writeb(TW68_SAT_U, 0x80);	/* 24C */
	tw_writeb(TW68_SAT_V, 0x80);	/* 250 */
	tw_writeb(TW68_HUE, 0x00);	/* 254 */

	/* TODO - Check that none of these are set by control defaults */
	tw_writeb(TW68_SHARP2, 0x53);	/* 258	Mfg specified reset val */
	tw_writeb(TW68_VSHARP, 0x80);	/* 25C	Sharpness Coring val 8 */
	tw_writeb(TW68_CORING, 0x44);	/* 260	CTI and Vert Peak coring */
	tw_writeb(TW68_CNTRL2, 0x00);	/* 268	No power saving enabled */
	tw_writeb(TW68_SDT, 0x07);	/* 270	Enable shadow reg, auto-det */
	tw_writeb(TW68_SDTR, 0x7f);	/* 274	All stds recog, don't start */
	tw_writeb(TW68_CLMPG, 0x50);	/* 280	Clamp end at 40 sys clocks */
	tw_writeb(TW68_IAGC, 0x22);	/* 284	Mfg specified reset val */
	tw_writeb(TW68_AGCGAIN, 0xf0);	/* 288	AGC gain when loop disabled */
	tw_writeb(TW68_PEAKWT, 0xd8);	/* 28C	White peak threshold */
	tw_writeb(TW68_CLMPL, 0x3c);	/* 290	Y channel clamp level */
/*	tw_writeb(TW68_SYNCT, 0x38);*/	/* 294	Sync amplitude */
	tw_writeb(TW68_SYNCT, 0x30);	/* 294	Sync amplitude */
	tw_writeb(TW68_MISSCNT, 0x44);	/* 298	Horiz sync, VCR detect sens */
	tw_writeb(TW68_PCLAMP, 0x28);	/* 29C	Clamp pos from PLL sync */
	/* Bit DETV of VCNTL1 helps sync multi cams/chip board */
	tw_writeb(TW68_VCNTL1, 0x04);	/* 2A0 */
	tw_writeb(TW68_VCNTL2, 0);	/* 2A4 */
	tw_writeb(TW68_CKILL, 0x68);	/* 2A8	Mfg specified reset val */
	tw_writeb(TW68_COMB, 0x44);	/* 2AC	Mfg specified reset val */
	tw_writeb(TW68_LDLY, 0x30);	/* 2B0	Max positive luma delay */
	tw_writeb(TW68_MISC1, 0x14);	/* 2B4	Mfg specified reset val */
	tw_writeb(TW68_LOOP, 0xa5);	/* 2B8	Mfg specified reset val */
	tw_writeb(TW68_MISC2, 0xe0);	/* 2BC	Enable colour killer */
	tw_writeb(TW68_MVSN, 0);	/* 2C0 */
	tw_writeb(TW68_CLMD, 0x05);	/* 2CC	slice level auto, clamp med. */
	tw_writeb(TW68_IDCNTL, 0);	/* 2D0	Writing zero to this register
					 *	selects NTSC ID detection,
					 *	but doesn't change the
					 *	sensitivity (which has a reset
					 *	value of 1E).  Since we are
					 *	not doing auto-detection, it
					 *	has no real effect */
	tw_writeb(TW68_CLCNTL1, 0);	/* 2D4 */
	tw_writel(TW68_VBIC, 0x03);	/* 010 */
	tw_writel(TW68_CAP_CTL, 0x03);	/* 040	Enable both even & odd flds */
	tw_writel(TW68_DMAC, 0x2000);	/* patch set had 0x2080 */
	tw_writel(TW68_TESTREG, 0);	/* 02C */

	/*
	 * Some common boards, especially inexpensive single-chip models,
	 * use the GPIO bits 0-3 to control an on-board video-output mux.
	 * For these boards, we need to set up the GPIO register into
	 * "normal" mode, set bits 0-3 as output, and then set those bits
	 * zero.
	 *
	 * Eventually, it would be nice if we could identify these boards
	 * uniquely, and only do this initialisation if the board has been
	 * identify.  For the moment, however, it shouldn't hurt anything
	 * to do these steps.
	 */
	tw_writel(TW68_GPIOC, 0);	/* Set the GPIO to "normal", no ints */
	tw_writel(TW68_GPOE, 0x0f);	/* Set bits 0-3 to "output" */
	tw_writel(TW68_GPDATA, 0);	/* Set all bits to low state */

	/* Initialize the device control structures */
	mutex_init(&dev->lock);
	spin_lock_init(&dev->slock);

	/* Initialize any subsystems */
	tw68_video_init1(dev);
	return 0;
}

static irqreturn_t tw68_irq(int irq, void *dev_id)
{
	struct tw68_dev *dev = dev_id;
	u32 status, orig;
	int loop;

	status = orig = tw_readl(TW68_INTSTAT) & dev->pci_irqmask;
	/* Check if anything to do */
	if (0 == status)
		return IRQ_NONE;	/* Nope - return */
	for (loop = 0; loop < 10; loop++) {
		if (status & dev->board_virqmask)	/* video interrupt */
			tw68_irq_video_done(dev, status);
		status = tw_readl(TW68_INTSTAT) & dev->pci_irqmask;
		if (0 == status)
			return IRQ_HANDLED;
	}
	dev_dbg(&dev->pci->dev, "%s: **** INTERRUPT NOT HANDLED - clearing mask (orig 0x%08x, cur 0x%08x)",
			dev->name, orig, tw_readl(TW68_INTSTAT));
	dev_dbg(&dev->pci->dev, "%s: pci_irqmask 0x%08x; board_virqmask 0x%08x ****\n",
			dev->name, dev->pci_irqmask, dev->board_virqmask);
	tw_clearl(TW68_INTMASK, dev->pci_irqmask);
	return IRQ_HANDLED;
}

static int tw68_initdev(struct pci_dev *pci_dev,
				     const struct pci_device_id *pci_id)
{
	struct tw68_dev *dev;
	int vidnr = -1;
	int err;

	dev = devm_kzalloc(&pci_dev->dev, sizeof(*dev), GFP_KERNEL);
	if (NULL == dev)
		return -ENOMEM;

	dev->instance = v4l2_device_set_name(&dev->v4l2_dev, "tw68",
						&tw68_instance);

	err = v4l2_device_register(&pci_dev->dev, &dev->v4l2_dev);
	if (err)
		return err;

	/* pci init */
	dev->pci = pci_dev;
	if (pci_enable_device(pci_dev)) {
		err = -EIO;
		goto fail1;
	}

	dev->name = dev->v4l2_dev.name;

	if (UNSET != latency) {
		pr_info("%s: setting pci latency timer to %d\n",
		       dev->name, latency);
		pci_write_config_byte(pci_dev, PCI_LATENCY_TIMER, latency);
	}

	/* print pci info */
	pci_read_config_byte(pci_dev, PCI_CLASS_REVISION, &dev->pci_rev);
	pci_read_config_byte(pci_dev, PCI_LATENCY_TIMER,  &dev->pci_lat);
	pr_info("%s: found at %s, rev: %d, irq: %d, latency: %d, mmio: 0x%llx\n",
		dev->name, pci_name(pci_dev), dev->pci_rev, pci_dev->irq,
		dev->pci_lat, (u64)pci_resource_start(pci_dev, 0));
	pci_set_master(pci_dev);
	if (!pci_dma_supported(pci_dev, DMA_BIT_MASK(32))) {
		pr_info("%s: Oops: no 32bit PCI DMA ???\n", dev->name);
		err = -EIO;
		goto fail1;
	}

	switch (pci_id->device) {
	case PCI_DEVICE_ID_6800:	/* TW6800 */
		dev->vdecoder = TW6800;
		dev->board_virqmask = TW68_VID_INTS;
		break;
	case PCI_DEVICE_ID_6801:	/* Video decoder for TW6802 */
		dev->vdecoder = TW6801;
		dev->board_virqmask = TW68_VID_INTS | TW68_VID_INTSX;
		break;
	case PCI_DEVICE_ID_6804:	/* Video decoder for TW6804 */
		dev->vdecoder = TW6804;
		dev->board_virqmask = TW68_VID_INTS | TW68_VID_INTSX;
		break;
	default:
		dev->vdecoder = TWXXXX;	/* To be announced */
		dev->board_virqmask = TW68_VID_INTS | TW68_VID_INTSX;
		break;
	}

	/* get mmio */
	if (!request_mem_region(pci_resource_start(pci_dev, 0),
				pci_resource_len(pci_dev, 0),
				dev->name)) {
		err = -EBUSY;
		pr_err("%s: can't get MMIO memory @ 0x%llx\n",
			dev->name,
			(unsigned long long)pci_resource_start(pci_dev, 0));
		goto fail1;
	}
	dev->lmmio = ioremap(pci_resource_start(pci_dev, 0),
			     pci_resource_len(pci_dev, 0));
	dev->bmmio = (__u8 __iomem *)dev->lmmio;
	if (NULL == dev->lmmio) {
		err = -EIO;
		pr_err("%s: can't ioremap() MMIO memory\n",
		       dev->name);
		goto fail2;
	}
	/* initialize hardware #1 */
	/* Then do any initialisation wanted before interrupts are on */
	tw68_hw_init1(dev);

	/* get irq */
	err = devm_request_irq(&pci_dev->dev, pci_dev->irq, tw68_irq,
			  IRQF_SHARED, dev->name, dev);
	if (err < 0) {
		pr_err("%s: can't get IRQ %d\n",
		       dev->name, pci_dev->irq);
		goto fail3;
	}

	/*
	 *  Now do remainder of initialisation, first for
	 *  things unique for this card, then for general board
	 */
	if (dev->instance < TW68_MAXBOARDS)
		vidnr = video_nr[dev->instance];
	/* initialise video function first */
	err = tw68_video_init2(dev, vidnr);
	if (err < 0) {
		pr_err("%s: can't register video device\n",
		       dev->name);
		goto fail4;
	}
	tw_setl(TW68_INTMASK, dev->pci_irqmask);

	pr_info("%s: registered device %s\n",
	       dev->name, video_device_node_name(&dev->vdev));

	return 0;

fail4:
	video_unregister_device(&dev->vdev);
fail3:
	iounmap(dev->lmmio);
fail2:
	release_mem_region(pci_resource_start(pci_dev, 0),
			   pci_resource_len(pci_dev, 0));
fail1:
	v4l2_device_unregister(&dev->v4l2_dev);
	return err;
}

static void tw68_finidev(struct pci_dev *pci_dev)
{
	struct v4l2_device *v4l2_dev = pci_get_drvdata(pci_dev);
	struct tw68_dev *dev =
		container_of(v4l2_dev, struct tw68_dev, v4l2_dev);

	/* shutdown subsystems */
	tw_clearl(TW68_DMAC, TW68_DMAP_EN | TW68_FIFO_EN);
	tw_writel(TW68_INTMASK, 0);

	/* unregister */
	video_unregister_device(&dev->vdev);
	v4l2_ctrl_handler_free(&dev->hdl);

	/* release resources */
	iounmap(dev->lmmio);
	release_mem_region(pci_resource_start(pci_dev, 0),
			   pci_resource_len(pci_dev, 0));

	v4l2_device_unregister(&dev->v4l2_dev);
}

#ifdef CONFIG_PM

static int tw68_suspend(struct pci_dev *pci_dev , pm_message_t state)
{
	struct v4l2_device *v4l2_dev = pci_get_drvdata(pci_dev);
	struct tw68_dev *dev = container_of(v4l2_dev,
				struct tw68_dev, v4l2_dev);

	tw_clearl(TW68_DMAC, TW68_DMAP_EN | TW68_FIFO_EN);
	dev->pci_irqmask &= ~TW68_VID_INTS;
	tw_writel(TW68_INTMASK, 0);

	synchronize_irq(pci_dev->irq);

	pci_save_state(pci_dev);
	pci_set_power_state(pci_dev, pci_choose_state(pci_dev, state));
	vb2_discard_done(&dev->vidq);

	return 0;
}

static int tw68_resume(struct pci_dev *pci_dev)
{
	struct v4l2_device *v4l2_dev = pci_get_drvdata(pci_dev);
	struct tw68_dev *dev = container_of(v4l2_dev,
					    struct tw68_dev, v4l2_dev);
	struct tw68_buf *buf;
	unsigned long flags;

	pci_set_power_state(pci_dev, PCI_D0);
	pci_restore_state(pci_dev);

	/* Do things that are done in tw68_initdev ,
		except of initializing memory structures.*/

	msleep(100);

	tw68_set_tvnorm_hw(dev);

	/*resume unfinished buffer(s)*/
	spin_lock_irqsave(&dev->slock, flags);
	buf = container_of(dev->active.next, struct tw68_buf, list);

	tw68_video_start_dma(dev, buf);

	spin_unlock_irqrestore(&dev->slock, flags);

	return 0;
}
#endif

/* ----------------------------------------------------------- */

static struct pci_driver tw68_pci_driver = {
	.name	  = "tw68",
	.id_table = tw68_pci_tbl,
	.probe	  = tw68_initdev,
	.remove	  = tw68_finidev,
#ifdef CONFIG_PM
	.suspend  = tw68_suspend,
	.resume   = tw68_resume
#endif
};

module_pci_driver(tw68_pci_driver);