summaryrefslogtreecommitdiffstats
path: root/target/linux/ath79
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Huawei AP5030DNMarco von Rosenberg2024-03-316-0/+313
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO enterprise access point with two Gigabit Ethernet ports and PoE support. Hardware highlights: - CPU: QCA9550 SoC at 720MHz - RAM: 256MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi 2.4GHz: QCA9550-internal radio - Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC - Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY - Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY - PoE: input through Ethernet 1 port - Standalone 12V/2A power input - Serial console externally available through RJ45 port - External watchdog: SGM706 (1.6s timeout) Serial console: 9600n8 (9600 baud, no stop bits, no parity, 8 data bits) MAC addresses: Each device has 32 consecutive MAC addresses allocated by the vendor, which don't overlap between devices. This was confirmed with multiple devices with consecutive serial numbers. The MAC address range starts with the address on the label. To be able to distinguish between the interfaces, the following MAC address scheme is used: - eth0 = label MAC - eth1 = label MAC + 1 - radio0 (Wi-Fi 5GHz) = label MAC + 2 - radio1 (Wi-Fi 2.4GHz) = label MAC + 3 Installation: 0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP 1. Power up the AP 2. At prompt "Press f or F to stop Auto-Boot in 3 seconds", do what they say. Log in with default admin password "admin@huawei.com". 3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot". Replace IP address as needed: > setenv serverip 192.168.1.10 > setenv ipaddr 192.168.1.1 > setenv rambootfile openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin > saveenv > run ramboot 4. Optional but recommended as the factory firmware cannot be downloaded publicly: Back up contents of "firmware" partition using the web interface or ssh: $ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin 5. Run sysupgrade using sysupgrade image. OpenWrt shall boot from flash afterwards. Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website): 1. Start a TFTP server in the directory where the firmware upgrade package is located 2. Boot to u-boot as described above 3. Install firmware upgrade package and format the config partitions: > update system FatAP5X30XN_SOMEVERSION.bin > format_fs Return to factory firmware (from previously created backup): 1. Copy over the firmware partition backup to /tmp, for example using scp 2. Use sysupgrade with force to restore the backup: sysupgrade -F huawei_ap5030dn_fw_backup.bin 3. Boot AP to U-Boot as described above Quirks and known issues ----------------------- - On initial power-up, the Huawei-modified bootloader suspends both ethernet PHYs (it sets the "Power Down" bit in the MII control register). Unfortunately, at the time of the initial port, the kernel driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume callback defined which would clear this bit. This makes the PHY unusable since it remains suspended forever. This is why the backported kernel patches in this commit are required which add this callback and for completeness also a suspend callback. - The stock firmware has a semi dual boot concept where the primary kernel uses a squashfs as root partition and the secondary kernel uses an initramfs. This dual boot concept is circumvented on purpose to gain more flash space and since the stock firmware's flash layout isn't compatible with mtdsplit. - The external watchdog's timeout of 1.6s is very hard to satisfy during bootup. This is why the GPIO15 pin connected to the watchdog input is configured directly in the LZMA loader to output the CPU_CLK/4 signal which keeps the watchdog happy until the wdt-gpio kernel driver takes over. Because it would also take too long to read the whole kernel image from flash, the uImage header only includes the loader which then reads the kernel image from flash after GPIO15 is configured. Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de> [fixed 6.6 backport patch naming] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: move D-Link DAP-1720 A1 to tiny sub-targetShiji Yang2024-03-308-46/+43
| | | | | | | | | | | This device only has 64 MiB RAM and ath10k wireless driver will consume a lot of memory. Let's move it to the tiny sub-target to get extra 7 MiB of free space. In this way, we can extend their lifetime to receive support for the next OpenWrt LTS version. This patch also trims the duplicate "recovery.bin" image as it's the same as the "factory.bin". Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move D-Link DIR-859 and DIR-869 series to tiny sub-targetShiji Yang2024-03-308-56/+72
| | | | | | | | | | These devices only have 64 MiB RAM and ath10k wireless driver will consume a lot of memory. Let's move them to the tiny sub-target to get extra 7 MiB of free space. In this way, we can extend their lifetime to receive support for the next OpenWrt LTS version. This patch also trims the USB package for the non-existent USB port. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: tiny: enable NVMEM u-boot-env driverShiji Yang2024-03-301-0/+2
| | | | | | | | The upcoming D-Link devices to the tiny sub-target require it to parse the u-env MAC address. The kernel size will increase by about 1 KiB. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move seama image recipe to the common MakefileShiji Yang2024-03-302-18/+18
| | | | | | | Move seama image recipe to the common Makefile in order for some tiny sub-target D-Link devices can share it. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: disable building small Flash EnGenius devicesShiji Yang2024-03-301-0/+3
| | | | | | | The buildbot has not successfully built them for a long time due to small Flash size. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: register ttyATH1 as OpenWrt console for ELECOM WAB-I1750-PSINAGAKI Hiroshi2024-03-241-0/+29
| | | | | | | Add a hotplug script and add ttyATH1 on ELECOM WAB-I1750-PS to /etc/inittab while booting for using that console as an OpenWrt console. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: register all ttys as Linux console for ELECOM WAB-I1750-PSINAGAKI Hiroshi2024-03-241-0/+4
| | | | | | | | | Register ttyS0 and ttyATH1 as Linux console on ELECOM WAB-I1750-PS. ttyS0 provides "SERVICE" port and internal pin header for debugging and recoverying by maker, ttyATH1 provides "SERIAL" port for configuration by users. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add missing kernel config symbolsShiji Yang2024-03-131-0/+4
| | | | | | Refresh kernel configs to add the missing symbols. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: remove obsolete 5.15 kernel supportShiji Yang2024-03-1339-3984/+10
| | | | | | | The 5.15 kenel config file, patches and version switches will be removed in this patch. We will introduce kernel 6.6 support soon. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: switch default kernel to 6.1Shiji Yang2024-03-131-2/+1
| | | | | | The 6.1 kernel has been tested for over half a year. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add support for D-Link COVR-C1200 A1Sebastian Schaper2024-03-094-0/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The COVR-C1200 devices are sold as "Whole Home Mesh Wi-Fi" sets in packs of two (COVR-C1202) and three (COVR-C1203). Specifications: * QCA9563, 16 MiB flash, 128 MiB RAM, 2x3:2 802.11n * QCA9886 2x2:2 801.11ac Wave 2 * AR8337, 2 Gigabit ports (1: WAN; 2: LAN) * USB Type-C power connector (5V, 3A) Installation COVR Point A: * In factory reset state: OEM Web UI is at 192.168.0.50 no DHCP, skip wizard by directly accessing: http://192.168.0.50/UpdateFirmware_Simple.html * After completing setup wizard: Web UI is at 192.168.0.1 DHCP enabled, login with empty password * Flash factory.bin * Perform a factory reset to restore OpenWrt UCI defaults Installation COVR Points B: * OEM Web UI is at 192.168.0.50, no DHCP, empty password * Flash factory.bin * Perform a factory reset to restore OpenWrt UCI defaults Recovery: * Keep reset button pressed during power on * Recovery Web UI is at 192.168.0.50, no DHCP * Flash factory.bin used to work best with Chromium-based browsers or curl: curl -F firmware=@factory.bin \ http://192.168.0.50/upgrade.cgi since this fails to work on modern Linux systems, there is also a script dlink_recovery_upload.py Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: split dtsi for D-Link COVR-P2500Sebastian Schaper2024-03-093-166/+177
| | | | | | in preparation of adding COVR-C1200 Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: cleanup and enable uart1 on ELECOM WAB-I1750-PSINAGAKI Hiroshi2024-03-081-23/+8
| | | | | | | | | | | | Cleanup uart1-related node on ELECOM WAB-I1750-PS and enable it for "SERIAL" port on the case. "SERIAL" port can be used for OpenWrt console by adding the following line to /etc/inittab and rebooting: ttyATH1::askfirst:/usr/libexec/login.sh Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: drop unnecessary &uart node from dtsi of QCA955x devicesINAGAKI Hiroshi2024-03-082-8/+0
| | | | | | &uart (uart0) is already enabled in qca955x.dtsi by default. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add aliases to qca955x.dtsi for uart0/1INAGAKI Hiroshi2024-03-0810-9/+5
| | | | | | | | | | | | | | Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to qca955x.dtsi, to enable uart1 on Linux Kernel. without this: [ 0.342915] ar933x-uart 18500000.uart: unable to get alias id, err=-19 Additionally, remove "serial0 = &uart;" alias from QCA955x device dts/dtsi files. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add HighSpeed UART (uart1) support for QCA955xINAGAKI Hiroshi2024-03-081-0/+12
| | | | | | | Add HighSpeed UART support to QCA955x series SoCs as a secondary UART (uart1). This UART is compatible with qca,ar9330-uart. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: rename label of primary UART on QCA955x to "uart0"INAGAKI Hiroshi2024-03-081-1/+1
| | | | | | | | Rename the DT label of the primary UART on Qualcomm Atheros QCA955x series SoCs to "uart0" from "uart" for the preparation to add HighSpeed UART (uart1) support. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 5.15 to 5.15.149Hauke Mehrtens2024-03-072-4/+5
| | | | | | | | | | | Removed because it is upstream: generic/pending-5.15/540-ksmbd-only-v2-leases-handle-the-directory.patch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=81ea755b8fa57ce186f56f14b709cf491c2a5505 Manually Adapted the following patch: ath79/patches-5.15/900-unaligned_access_hacks.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 6.1 to 6.1.80John Audia2024-03-051-1/+1
| | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.80 Manually rebased: generic/hack-6.1/650-netfilter-add-xt_FLOWOFFLOAD-target.patch[1] All other patches automatically rebased. 1. Acknowledgement to @heheb and @DragonBluep. Upstream commit for ref: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.80&id=9c5662e95a8dcc232c3ef4deb21033badcd260f6 Build system: x86/64 Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3 Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: add support for ELECOM WAB-I1750-PSINAGAKI Hiroshi2024-03-024-0/+80
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point, based on QCA9558. Specification: - SoC : Qualcomm Atheros QCA9558 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 3T3R - 2.4 GHz : Qualcomm Atheros QCA9558 (SoC) - 5 GHz : Qualcomm Atheros QCA9880 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 2x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - "SERIAL" : RS232C (+-12V) - port : ? - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - settings : 115200n8 - note : compatible with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1.04 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-I1750-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - "SERIAL" port is provided by HS UART on QCA9558 SoC that has compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported on Linux Kernel and OpenWrt. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text)) 2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text)) 5GHz : 00:90:FE:xx:xx:0B [original work] Signed-off-by: Yanase Yuki <dev@zpc.st> [update for NVMEM and others] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for ELECOM WAB-S1167-PSINAGAKI Hiroshi2024-03-024-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point, based on QCA9557. Specification: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm Atheros QCA9557 (SoC) - 5 GHz : Qualcomm Atheros QCA9882 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 1x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-S1167-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - The same PCB is used with WAB-S600-PS. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text)) 5GHz : 00:90:FE:xx:xx:05 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for ELECOM WAB-S600-PSINAGAKI Hiroshi2024-03-025-5/+303
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based on QCA9557. This device also supports 11ac (Wi-Fi 5) with the another official firmware. Specification: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB (2x Winbond W9751G6KB251) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm Atheros QCA9557 (SoC) - 5 GHz : Qualcomm Atheros QCA9882 - Ethernet : 2x 10/100/1000 Mbps - phy ("PD") : Atheros AR8035 - phy ("PSE") : Atheros AR8033 - LEDs/keys (GPIO) : 3x/3x - UART : 1x RJ-45 port - "SERVICE" : TTL (3.3V) - port : ttyS0 - assignment : 1:3.3V, 2:GND, 3:TX, 4:RX - settings : 115200n8 - note : no compatibility with "Cisco console cable" - Buzzer : 1x GPIO-controlled - USB : 1x USB 2.0 Type-A - Power : DC jack or PoE - DC jack : 12 VDC, 1 A (device only, rating) - PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating) - note : supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE Flash instruction using factory.bin image: 1. Boot WAB-S600-PS without no upstream connection (or PoE connection without DHCP) 2. Access to the WebUI ("http://192.168.3.1") on the device and open firmware update page ("ツールボックス" -> "ファームウェア更新") 3. Select the OpenWrt factory.bin image and click update ("アップデート") button 4. Wait ~120 seconds to complete flashing Revert to OEM firmware: 1. Download the latest OEM firmware 2. Remove 128 bytes(0x80) header from firmware image 3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val) 4. Upload the decoded firmware to the device 5. Flash to "firmware" partition by mtd command 6. Reboot Notes: - To use the "SERVICE" port, the connection of 3.3V line is also required to enable console output. The uart line of "SERVICE" is branched out from the internal pin header with 74HC126D and 3.3V line is connected to OE pin on it. - The same PCB is used with WAB-S1167-PS. - To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC 3.5 A adapter is recommended. (official: WAB-EX-ADP1) MAC addresses: Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text)) 2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text)) 5GHz : BC:5C:4C:xx:xx:7D [original work of common dtsi part for WAB-I1750-PS] Signed-off-by: Yanase Yuki <dev@zpc.st> [adding support for WAB-S600-PS] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: nand: add SUPPORTED_DEVICES for Meraki MR18Samuele Longhi2024-02-291-0/+1
| | | | | | | This adds the board name from ar71xx to support upgrade without -F for the Meraki MR18. Signed-off-by: Samuele Longhi <agave@dracaena.it>
* kernel: bump 6.1 to 6.1.79John Audia2024-02-241-2/+3
| | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.79 Manually rebased: ath79/patches-6.1/900-unaligned_access_hacks.patch All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, flogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, flogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: update WA/XC devices UBNT_VERSION to 8.7.4Martin Garbe2024-02-191-3/+3
| | | | | | | | | | Ubiquiti WA devices with newer hw version (sold 2023) require UBNT_VERSION to be at least 8.7.4, otherwise the image is rejected. For consistency, also increase version number for XC devices. Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
* ath79: generic: fix the alphabetical order in 02_networkFoica David2024-02-161-5/+5
| | | | | | | This commit fixes the alphabetical order in 02_network. The 2 deco devices in ath79_setup_interfaces() were in the wrong place. Signed-off-by: Foica David <superh552@gmail.com>
* kernel: bump 6.1 to 6.1.77John Audia2024-02-081-1/+1
| | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.77 Removed upstreamed: generic/backport-6.1/707-v6.8-01-net-phy-at803x-fix-passing-the-wrong-reference-for-c.patch[1] generic/backport-6.1/796-v6.8-ipmr-fix-kernel-panic-when-forwarding-mcast-packets.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.77&id=7dc0fefd37dd5fb03fdac6e3e01b1c2291148ccb 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.77&id=d2f1b7fe74afd66298dbb3c7b39e7b62e4df1724 Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.76John Audia2024-02-081-1/+1
| | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.76 All patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: convert to new LED color/function format where possibleChristian Marangi2024-02-07287-640/+1663
| | | | | | | | Initial conversion to new LED color/function format and drop label format where possible. The same label is composed at runtime. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath79: drop redundant label with new LED color/function formatChristian Marangi2024-02-0712-24/+0
| | | | | | | | | Drop redundant label with new LED color/function format declared. This was needed previously when the new format wasn't supported by leds.sh functions script. Now that is supported this property can be removed in favor of the new format. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath79: Modify GL.iNer GL-S200 lan wan interfaceWeiping Yang2024-02-021-2/+0
| | | | | | | | | | | | | Specifications: lan: eth0 wan: eth1 Problem Description: The lan wan port is reversed with the current machine. Use eth0 as LAN port and eth1 as WAN port. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ath79: add WAN definition for GL.iNET GL-E750 (Mudi)Jan Fuchs2024-02-021-5/+5
| | | | | | | Add the default WAN interface to use QMI, to have WAN configured right from the start. Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
* ath79: add WWAN serial driver and qmi for GL.iNET GL-E750 (Mudi)Jan Fuchs2024-02-021-1/+2
| | | | | | | | The driver for the cellular modems serial interface and qmi was missing from the default device packages. The driver is required to interact with the modem using AT commands. Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
* kernel: bump 5.15 to 5.15.148John Audia2024-02-011-1/+1
| | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.148 Removed upstreamed: generic/hack-5.15/321-powerpc_crtsavres_prereq.patch[1] Manually rebased: target/linux/octeontx/patches-5.15/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.148&id=0b11a145eb00d51f7ef18cfcae587b93f9adb1e9 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit?h=v5.15.148&id=b67064bd372300a75293efbbc70624996dccffd4 Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 6.1 to 6.1.75John Audia2024-02-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.75 Removed upstreamed: generic/hack-6.1/321-powerpc_crtsavres_prereq.patch[1] generic/pending-6.1/540-ksmbd-only-v2-leases-handle-the-directory.patch[2] Rebased: bcm27xx/patches-6.1/950-0670-fbdev-Don-t-cancel-deferred-work-if-pagelist-empty.patch[3] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.75&id=16b88e68b85d5520c28498bb847358ff6300cb90 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/fs/smb?h=v6.1.75&id=c866866c795296d3637ab0d48a3d8a3ef5d6f4a3 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.75&id=81f444f22816a82ada2cc787a2845cffc8c584a6 Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: convert ath10k calibration data to NVMEM (ASCII MAC)Shiji Yang2024-02-0115-68/+174
| | | | | | | | | This patch converts ath10k calibration data to NVMEM format for wave 1 devices with mtd ASCII MAC address. The "calibration" NVMEM cell size is 0x844. All unportable MAC address settings have been moved to '10_fix_wifi_mac' scripts. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert ath10k calibration data to NVMEM (binary MAC)Shiji Yang2024-02-0138-122/+543
| | | | | | | | This patch converts ath10k calibration data to NVMEM format for wave 1 devices with mtd binary MAC address. The "calibration" NVMEM cell size is 0x844. The MAC addresses are assigned via dts. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert ath10k calibration data to NVMEM (built-in MAC)Shiji Yang2024-02-0122-43/+211
| | | | | | | | This patch converts ath10k calibration data to NVMEM format for wave 1 devices with built-in MAC address. The "calibration" NVMEM cell size is 0x844. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert ath10k pre-calibration data to NVMEM (ASCII MAC)Shiji Yang2024-02-016-21/+71
| | | | | | | | | This patch converts ath10k pre-calibration data to NVMEM format for wave 2 devices with mtd ASCII MAC address. The "pre-calibration" NVMEM cell size is 0x2f20. All unportable MAC address settings have been moved to '10_fix_wifi_mac' scripts. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert ath10k pre-calibration data to NVMEM (binary MAC)Shiji Yang2024-02-0121-80/+342
| | | | | | | | This patch converts ath10k pre-calibration data to NVMEM format for wave 2 devices with mtd binary MAC address. The "pre-calibration" NVMEM cell size is 0x2f20. The MAC addresses are assigned via dts. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert ath10k pre-calibration data to NVMEM (built-in MAC)Shiji Yang2024-02-015-12/+35
| | | | | | | | This patch converts ath10k pre-calibration data to NVMEM format for wave 2 devices with built-in MAC address. The "pre-calibration" NVMEM cell size is 0x2f20. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add back board-2.bin to COMFAST devicesShiji Yang2024-02-011-2/+0
| | | | | | | | The ath10k driver will load both pre-calibration data and board-2.bin if board-2.bin exists. So it's not necessary to remove it. And this change won't increase jffs2 image size. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: add Ubiquiti Rocket M XW as alternate name to Bullet M XWLech Perczak2024-01-251-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional GPS receiver, with two external RP-SMA antenna connections, based on AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable with the same image. Specs: - CPU: Atheros AR9342 MIPS SoC at 535MHz - RAM: 64MB DDR400 - ROM: 8MB SPI-NOR in SO16W package, MX25L6408E - Wi-Fi Atheros AR9342 built-in 2x2:2 radio - Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to magnetics - Power: 24V passive PoE input. Installation: please refer to Ubiquiti Bullet M2HP for documentation. The device runs with exactly same image as the Bullet, and after fixes in preceding commit, is fully functional again. Add the alternative name to the build system. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-bullet-m-xw: fix Ethernet PHY trafficLech Perczak2024-01-251-2/+1
| | | | | | | | | | | | | | | | Since commit 6f2e1b7485f0 ("ath79: disable delays on AT803X config init") Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of outbound traffic on the Ethernet port. This was caused by the fact, the U-boot has set this during boot and it wasn't reset by the PHY driver, and the corresponding setting in device tree was wrong. Set the 'phy-mode = "rgmii-txid"' at the &eth0, and drop this property from PHY node, as it is not parsed there. This causes the device to connect using Ethernet once again. Fixes: db4b6535f837 ("ath79: Add support for Ubiquity Bullet M (XW)") Fixes: 6f2e1b7485f0 ("ath79: disable delays on AT803X config init") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-bullet-m-xw: set PHY max-speed to 100MbpsLech Perczak2024-01-251-0/+1
| | | | | | | | Onboard AR8035 PHY supports 1000Base-T operation, but onboard Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and lower. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: fix mac address on eap2x5-1port devicesNikolay Martynov2024-01-237-36/+12
| | | | | | | | | | | | | | | Commit e816591e226a ("ath79: qca: convert to nvmem-layout") mistakenly switched the source of the mac address from the 'info' to 'art' partition. This patch updates all devices that share same 'parent' device tree file and was tested to fix the problem for eap225-outdoor-v3 - device that I actually own. Fixes: e816591e226a ("ath79: qca: convert to nvmem-layout") Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> [amend commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti ↵Samuele Longhi2024-01-2012-73/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) Add support for Ubiquiti LiteBeam M5 (XW). The device was previously supported in ar71xx. See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577 Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW) Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone. Tested on: - Ubiquiti LiteBeam M5 (XW) - Ubiquiti PowerBeam M5 (XW) This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data Checked that the caldata size in the eeprom partition are actually 0x440 on: - Ubiquiti PowerBeam M5 (XW) - Ubiquiti Nanostation M5 (XW) - Ubiquiti LiteBeam M5 (XW) - Ubiquiti AirGrid M5 HP (XW) Signed-off-by: Samuele Longhi <agave@dracaena.it>
* kernel: bump 6.1 to 6.1.72John Audia2024-01-191-1/+1
| | | | | | | | | | | | | | | Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.72 Manually rebased: generic/hack-6.1/650-netfilter-add-xt_FLOWOFFLOAD-target.patch All other patches automatically rebased. Build system: x86/64 Build-tested: x86/64/AMD Cezanne Run-tested: x86/64/AMD Cezanne Signed-off-by: John Audia <therealgraysky@proton.me>
* ath79: read back reset registerDavid Bauer2024-01-112-0/+66
| | | | | | | | | | | | | | | | | Read back the reset register in order to flush the cache. This fixes spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel DRAM chips. This issue was fixed in the past, but switching to the reset-driver specific implementation removed the cache barrier which was previously implicitly added by reading back the register in question. Link: https://github.com/freifunk-gluon/gluon/issues/2904 Link: https://github.com/openwrt/openwrt/issues/13043 Link: https://dev.archive.openwrt.org/ticket/17839 Link: f8a7bfe1cb2c ("MIPS: ath79: fix system restart") Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-18 00:04:20 +0000